Question about KitchenAid Food Processors

1 Answer

How to use the dough blade with my kitchenaid food processor

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • KitchenAid Master
  • 8,546 Answers
Ad

5 Suggested Answers

Anonymous

  • 1 Answer

SOURCE: stuck dough blade

On the DLC 7 Pro cuisinart the blade was removed by removing
the plastic bottom. Make sure the unit is unplugged. Remove the four rubber pads on the bottom. This was the hardest part because the pads are glued so securely that the inner rubber surface tears as it's removed. I used two flat blade screwdrivers and worked carefully, back and forth. Using a #2 philips, remove the four screws. Place the unit on its side and while inserting a screwdriver between a spoke and the motor frame gently turn the blade counter clockwise. Be careful not to put pressure against the cooling fins. Very little pressure was needed and the blade came right out. I might have been able to hold the shaft from turning without removing the bottom, by going through the vent slots in the bottom, but I was concerned with cracking the plastic. To replace the rubber pads I matched the design of the torn rubber pad with the shape (design) of the surface glued rubber and used thin two-sided tape.

Posted on Apr 05, 2008

Ad

QuietRiot

  • 145 Answers

SOURCE: Need to clean inside of handle on KitchenAid food processor

The plastic for the work bowl / handle is molded and one piece and cannot be disassembled. My best recommendation is to call Kitchenaid customer service to see what recommendations they have. Within one year warranty, they may replace the work bowl at no cost.

Their toll-free number is: 1-800-541-6390.

Posted on Jul 07, 2009

Anonymous

  • 72 Answers

SOURCE: My 12 cup kitchen aid food processor dough blade

Dough is normally water soluble. Try soaking it in water for a several days up to a week. Then try prying it loose.

Posted on Sep 17, 2009

Anonymous

  • 89 Answers

SOURCE: Need owners manual for kitchenaid food processor model # KFP740CR

http://www.kitchenaid.com/flash.cmd?/#/page/home
this site should help you out.
one thing, you can chop onions without crying.

Posted on Nov 08, 2009

angeloioc

  • 1 Answer

SOURCE: attachment stuck on shaft of food processor

put the mixing bowl up as much as possible. spray some wd40 into the groove between the attachement and the motor shaft. Wait for several minutes, then with a hammer and a piece of wood, give the bowl a good wack. With a few goes, it will gradually come off. I will be putting some butter inside the attachement from now on to keep it lubricated

Posted on Mar 09, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get a dough blade for kitchenAid food processor Model 4KFP 600 WH


Kitchen Aid list them, it's on this page called blade, dough

http://www.kitchenaidpartsonline.com/modellookup/index/thirdstep/keyword/KFP600/model_no/KFP600WH/model_id/398686/diagram_id/10083552

Feb 24, 2015 | KitchenAid Food Processors

1 Answer

Haw can i use ?


My food processor is one of my most-used appliances. I just got a new Cuisinart (at Costco - with an extra workbowl!) and use it at least twice a week. I grate cheeses like cheddar or swiss, pulverize parmesan, make bread crumbs, hummus, pesto, salsa... I make pasta dough in it before rolling out in my Kitchenaid pasta attachment. Pie crusts come together in a flash. And it's great during the holidays for chopping nuts and certain cookie doughs. I've chopped my own beef for burgers, etc, etc. I keep it in a cabinet but it's easy to pull out whenever I need it. And there are only 2 of us at home.

By the way, the blades are so sharp in the new machine that I cut my finger trying to clear something from the blade. I'll use a spatula next time!














ford performance chips.

May 25, 2012 | Food Processors

1 Answer

Attachment stuck on shaft of food processor


put the mixing bowl up as much as possible. spray some wd40 into the groove between the attachement and the motor shaft. Wait for several minutes, then with a hammer and a piece of wood, give the bowl a good wack. With a few goes, it will gradually come off. I will be putting some butter inside the attachement from now on to keep it lubricated

Jan 11, 2010 | KitchenAid KFP750 Food Processor

1 Answer

My 12 cup kitchen aid food processor dough blade is seriously stuck inside the bowl after I made some dough. How do I get it out?


Dough is normally water soluble. Try soaking it in water for a several days up to a week. Then try prying it loose.

Sep 17, 2009 | KitchenAid Food Processors

1 Answer

Magimix blade is stuck


You need to replace the spindle i'm afraid which gets worn after a time. There a UK company that sells replacements and tells you how to replace it. Not a big job though a bit tricky. magimixspares.com

Jun 28, 2009 | Magimix 5100 Cuisine Systeme Food...

2 Answers

Blade holding disc for Breville Food Processor Model No. FP7/FP8 Replacement required. Phone numbers required for contact.


Hi. I'm a Breville Service Centre.

No new parts for FP7 or FP8 are available, your best bet is to check out garage sales or you local Salvos/St Vinnies etc as people may sell their odd pieces once their motor dies. Which is rare because they were good machines!

Good luck!

Mar 18, 2009 | Food Processors

1 Answer

Kneading blade stuck


plz contact 022-23051554 /23095757

Feb 02, 2009 | KitchenAid KFP750 Food Processor

1 Answer

We can`t disasemble it with the dough blade in, any tips?


All of the blades "lock" (rest in a groove) when rotated clockwise. This is so they'll stay put when in operation. When you take the bowl out with a blade in, you're moving the pair in a clockwise direction. So, you lock the blade in, thus locking the bowl down. Either remove the blade first by rotating it counter clockwise, then up or move the blade back 1/10th of a turn after rotating the bowl as far as it will go clockwise.

Jan 02, 2009 | KitchenAid KFP750 Food Processor

Not finding what you are looking for?
Food Processors Logo

Related Topics:

185 people viewed this question

Ask a Question

Usually answered in minutes!

Top KitchenAid Food Processors Experts

ThaMp3Doctor
ThaMp3Doctor

Level 3 Expert

8597 Answers

ismash55

Level 2 Expert

138 Answers

john h

Level 3 Expert

22486 Answers

Are you a KitchenAid Food Processor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...