Question about Hobart Food Mixers

Open Question

Hobart CRS66A runs in a second or two then stops

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My Hobart D-300 keep stop after running about 10 minutes and stay idol about 5 minutes then I can push start button to run another 10 minutes, it seam like control unit stop after it getting over heat and...


If your mixer's motor was built by Hobart; there are thermsiters built in to the stator's windings that can cause this problem. Check the amp draw while it is running. Also if your are over loading the mixer or using the wrong speed,, that will cause an over heating problem. You should be able to get on the ITW Food Equipment Group / Hobart web site(s) and get capacity chart.

Mar 01, 2015 | Hobart Food Mixers

1 Answer

Hobart a200 first gear not working


slacken the big acorn nut away from the bottom of the planetary and then tighten the lock nut to the acorn nut. When adjusted and secured, the planetary should have a little vertical play, maybe 1/16".
That will stop the second gear driving from friction from being too tight.

Feb 27, 2014 | Hobart A200 Stand Mixer

1 Answer

My older model Hobart n50 mixer stopped working. The motor is running but three teeth on the fiber gear were broken off from the main gear in the transmission. While removing some of the grease, I found...


The best solution I can give you is to become a member at the Hobart Corp. website and use there schematics to find where the pin goes. It is free to use the parts catologues have a parts blowup.
Follow the link below:
https://feg.hobartcorp.com/CookieAuth.dll?GetLogon?curl=Z2FsalesZ2Fredirect.aspx&reason=2&formdir=2

Thank you for using FixYa, I hope this helps.

Jan 19, 2011 | Hobart N50 Stand Mixer

1 Answer

Hobart Legacy mixer error code oc3 will not run.


Hobart mixer, HL300, stops and flashes as oc3, wounded what is broken?

Dec 08, 2010 | Hobart HL600 Legacy Stand Mixer

1 Answer

Hobart D340 mixer will not hit 3rd gear


Check that the gear on the shaft that the clutch gear engages with does nort have a sheared key.

Feb 12, 2010 | Hobart D340-6007 Mixer

2 Answers

Hobart D300 Mixer, Will not shift from 2nd to 1st gear without coming to full stop, Ideas as to source of problem? It also seems to be making increased noise.


Hobart mixers are NOT designed to change gears while operating. The Hobart planetary gears are like the transmission in your car but, without the clutch. Everytime you change gears while unit is running you are tearing up the brass spacers, gears & seals. Time to call a QUALIFIED service tech to come out & sell you another planetary or rebuild your old one, about $2K, Buy a Varimixer if you want to change gears while unit is running, they use belts. Another planetary premature failur cause, over loading the bowl. Batters & icings- 75% bowl capacity, Dough 65% bowl capacity.

Jul 23, 2009 | Hobart D300 Stand Mixer

2 Answers

Hobart A-200 First Gear is Having Trouble


If the mixers are older the dive key shaft,spring or key are broken,if they are newer the key is sheared.Also check the nuts near the beater shaft and make sure there not too tight.

Nov 13, 2008 | Hobart A200 Stand Mixer

1 Answer

Sound like bearings


Ist check your agitator shaft for looseness. the shaft you put the beater on. wiggle side to side. if tight no play. If in first its quiet but you can here a grumble under load but second gets louder. and third even louder. If the shaft is tight. your gears down there are warn. you can take that all off with the two nuts underneath. and check the grease on the gears but even with new grease on them it most likely stay loud. grease it with hobart grease from your loacal hobart for the A-200 planitary not the transmision they also fve grease for Trans. if you can take the noise run it that way if not decide which arm & leg you want to give hobart for new gears.

Sep 10, 2008 | Hobart A200 Stand Mixer

1 Answer

Second Gear


Sorry so late for the reply.When the product slows down---how slow?can you grab the shaft and stop it from moving?What product are you mixing?

Feb 05, 2008 | Hobart D300-6036 Mixer

Not finding what you are looking for?
Food Mixers Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hobart Food Mixers Experts

Ross Keen

Level 3 Expert

1364 Answers

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Bruce Showalter

Level 2 Expert

133 Answers

Are you a Hobart Food Mixer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...