Question about Bissell Vacuums

1 Answer

Hi my Bissell Pro heat x2 revolution is leaving black marks on the carpet and noisy the rubber belt is is hot and smell like it’s burning can you help

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Bissell Master
  • 53,755 Answers

Roller brush jammed yp with lint , cords and rubbish
clean and replace the belt
take it to a vacuum repair shop

Posted on Apr 14, 2018

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

SOURCE: bissell revolution roller won't turn

these things are VERY sensitive to the roller being perfectly free of any haor or stuff. Clean the roller completely, put a new belt on, and make sure it is all turning perfectly before you plug it in...

Posted on Aug 30, 2008

Anonymous

  • 1 Answer

SOURCE: Vacuum smells like burning rubber

Usually when my vacuum smells like burning rubber, the belt needs to be changed and that is very easy to do. You just need to remove the the screws that hold in the rotator and put in a new belt. When the belt needs to be changed the vacuum will not pick up anything and this could make it seem like there is no suction. I hope this helps!

Posted on Nov 25, 2008

defrankond

CJ C

  • 66 Answers

SOURCE: not working

The bissell shampooers use belts t run the pump and the beater bar. if the master beltbroke which is the one that controls the pump and beater bar then yes the machine will not dispense water or turn the beater bar. it will have to be replaced *the belt that is*

Posted on Dec 02, 2008

Anonymous

  • 5 Answers

SOURCE: Replacing the little black rubber belt

bissell.com has videos on how to replace belts.

Posted on May 30, 2009

gon2oahu

  • 25 Answers

SOURCE: BISSELL PRO HEAT X2 CLEAN SHOT

Try checking the lint filter. It is located in the top clear plastic section (the one with the dial to switch from floor to tool use) and is on the underside. It is a small (1 inch square) red plastic filter with a little door on it. Open the door and you will probably find it is clogged with hair, carpet fibre., etc.. Clean this out and you will hopefully have suction again.

Posted on Sep 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bissell quickwash 1970E for carpets/hard floors won't come on


If the burning smell was like rubber burning it is probably the belt. If you only used it a few times I suggest bringing it back to place of purchase. A belt should not go after just a few times of use. Besides if anything is burning after just a few uses I would return it.

Mar 28, 2014 | Bissell Vacuums

1 Answer

Bissell lift off bagless making high pitched noise, fan seems to run for 30 seconds after shutting off, and a burning rubber smell, is it the belt, and how easy are they to change


The burning rubber smell is usually the belt. Be careful not to use it on your carpet as the rubber belt can get hot and liquify and really mess up your carpet (if you have one). Here's a link to some instructions for replacing the belt.

http://www.ehow.com/how_4550054_replace-drive-belt-bissell-powerforce.html

Good luck!

Mar 15, 2010 | Vacuums

1 Answer

My liftoff revolution smell like it is burning after I use it


That means that the belt is worn and is starting to slip. You need to replace the belt. Here is the belt you need and a manual you can view with instructions:

Bissell Lift-Off Revolution Belt and Manual

Mar 13, 2010 | Bissell LiftOff Revolution Pet Vac 37602...

1 Answer

Last time I used my Bissell Pet Hair Remover vacuum it smelled like something was burning and it left a black mark on the carpet. What should I do?


When you smell burning like that it usually indicates that the belt is worn and slipping on the motor shaft. You probably need to change the belt. You can get the belts for your model here:

Bissell Pet Hair Eraser Belts

Nov 11, 2009 | Bissell Upright Vacuum - The Pet Hair...

1 Answer

Replacing the little black rubber belt


bissell.com has videos on how to replace belts.

May 04, 2009 | Bissell 7920 ProHeat Pro-Tech Upright...

2 Answers

Vacuum smells like burning rubber when on, no suction, leaving black marks on carpet


Usually when my vacuum smells like burning rubber, the belt needs to be changed and that is very easy to do. You just need to remove the the screws that hold in the rotator and put in a new belt. When the belt needs to be changed the vacuum will not pick up anything and this could make it seem like there is no suction. I hope this helps!

Nov 25, 2008 | Hoover U6437-900 / U6439-900 Windtunnel...

1 Answer

Not working


The bissell shampooers use belts t run the pump and the beater bar. if the master beltbroke which is the one that controls the pump and beater bar then yes the machine will not dispense water or turn the beater bar. it will have to be replaced *the belt that is*

Nov 13, 2008 | Bissell 1697-7 Powersteamer Pro Deluxe...

Not finding what you are looking for?
Vacuums Logo

Related Topics:

250 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bissell Vacuums Experts

Brad Brown

Level 3 Expert

18127 Answers

CJ C
CJ C

Level 2 Expert

66 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Are you a Bissell Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...