Question about HP Boating

1 Answer

2009 evinrude etec 30 hp will start then stall after a few seconds

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 431 Answers

Clean the float bowl.. Even the efi systems have a float bowl which are prone to sticking from bad fuel. Ps. Use supreme gas only with zero ethanol . Ethanol eats your gas lines and will End black specks into your fuel filter. The higher the percentage the worse it is. And add stabilizer like seafoam. Check your fuel filter, and for crushed fuek line, and failed primer bulbs... these are all common issues.

Posted on Apr 24, 2018

Ad

5 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
miket756

Michael Thorpe

  • 2702 Answers

SOURCE: Runs for 30 sec then stalls

go to ebay and fine yourself a cheep fule computer there about £30 second hand i think yours has just packed up and its making the bike run very very ritch

Posted on Jun 02, 2010

Ted Maxwell

  • 3519 Answers

SOURCE: Why is it hard to steer a 2009 25 HP evinrude etec?

Hi Pablo:

I'd be looking for corrosion at the rotating bushing. There should be grease nipples to get lube into it. Grease, and lots of moving it should loosen it up.

Posted on Mar 06, 2015

glennsmart

Glenn Smart

  • 828 Answers

SOURCE: I have a 2013 evinrude etec 25 hp. It has only had less than 2 tanks of fuel ran through it. I took it out today and it would start but wouldn't stay running.

This is a 2 stroke engine - an outboard motor?

Two strokes are quite robust. The usual mistake people make with these engines (think of chainsaws, lawn mowers and hedge strimmers..) is to use car engine oil instead of the correct two stroke oil. Motor oil is completely incorrect and fouls the spark plug.

The other fault is to mix fuel and two stroke oil in the wrong ratio. Most chainsaws etc .. use a mix of 25:1 Too much oil causes oiling and misfiring of the plug. Too little oil causes excessive and fast wear.

Your engine starts up. That tends to suggest that everything is working ok up to a point.

However, look on the following link which deals with an overheating problem for that engine:

http://www.etecownersgroup.com/post/25hp-etec-problem-6107593

Posted on May 21, 2016

rgall3285

ray gallant

  • 64733 Answers

SOURCE: good day, i am looking for a pinion gear for a evinrude etec 250 HO, 2009 model? can you guys please assist?

we can not I would go to a dealer

Posted on Aug 10, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Engine wont rev when in neutral


take it to a service shop
I suspect that you put the new motor onto old fuel lines and the rubber on the insides of the primer and hoses has not broken down and is blocking the high speed jets or affecting the fuel pump valves
if it is fuel injected , the shop will be able to read the fault codes to find the faulty sensor

Aug 09, 2018 | Clymer Evinrude/Johnson 5-70 Hp...

1 Answer

Evinrude etec runs for a few min wot then Boggs down I changed the filters an plugs but still doing it runs fine at about 1500 rpm 150 evinrude


Check and see if one of the carbs are leaking. I also always recommend a can or two of dry gas in the tank. As water collects over time. also a can of sta-bil can remove gelling and clean out the jets.

Jul 01, 2018 | Boating

1 Answer

What is the idle timing for 1993 90hp evinrude


90 hp 1993 evinrude idle speed - MarineEngine

www.marineengine.com > ... > Johnson Evinrude Outboard Archive

Aug 3, 2008 - 2 posts - ‎2 authors
"How many rpm should the engine idle at,and where and how do you adjust it Thanks" 50 hp evinrude no idle and no top speed need assistance ...
2 posts
Jul 6, 2013
1993 50 HP 2 cyl Evinrude stalls, runs at idle when ...
22 posts
May 7, 2012
adjust carburators and idle speed 1993 48hp
2 posts
Jul 29, 2010
90 hp stalls when going in gear
9 posts
May 21, 2010
More results from www.marineengine.com

1993 Johnson 90-HP Runs Only At Idle Speed On Spring Start-Up

Johnson 1993 115 xflow Link and Sync - YouTube? 4:55https://www.youtube.com/watch?v=ReeuaVh8uZQNov 25, 2012 - Uploaded by Brian O'DellJohnson 1993 115 xflow Link and Sync. Brian O' ... Also if you can give me some details on how you got the ...DOWNLOAD Evinrude 90HP (90 HP) Repair Manual

Dec 14, 2015 | Boating

1 Answer

Why is it hard to steer a 2009 25 HP evinrude etec?


Hi Pablo:

I'd be looking for corrosion at the rotating bushing. There should be grease nipples to get lube into it. Grease, and lots of moving it should loosen it up.

Mar 06, 2015 | Boating

1 Answer

Evinrude etec 45


what is evinrude etec 45?????????????

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Apr 14, 2014 | Konica Minolta Office Equipment & Supplies

1 Answer

Evinrude will not start


Bad gas is one thing, 2nd may be dirt in carbs, 3rd fuel filter etc. May cracks in prime bulb. Lot of little things happen when set for some time w/o running. good luck

Dec 07, 2017 | Boating

Not finding what you are looking for?
Boating Logo

Related Topics:

488 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Boating Experts

vince

Level 3 Expert

1234 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Douglas Thorburn

Level 2 Expert

36 Answers

Are you a HP Boating Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...