Question about Asko Washing Machines

Open Question

Asko wash F3,after wash, drained water by hose,then put only 4 items thru rinse and spin..hose is fine...then works....help

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

prem mathew

  • 1294 Answers

SOURCE: Rinse water fills the washing machine when the spin cycle starts

Check your outlet filter, most likely it is blocked, preventing the water from draining out. Chk your pump too. Before this disconnect from the wall socket; and also check the pipe coming from the tub to the filter. Siphon out the excess water from inside the machine before you open the pipes.

Posted on May 18, 2007

Ad

Anonymous

  • 1 Answer

SOURCE: LG WD-8013F wont spin

Hi deppgirl,
I checked the lint filter at the front bottom left hand side and it was full of junk.  Once emptied it worked a treat.  Pull the flap down and turn the large knob anti-clockwise and pull to remove.  Good luck.

Posted on Apr 22, 2008

Anonymous

  • 27 Answers

SOURCE: Intuitive eco Iw811 Rinse 1 no water coming thru!

the 1st rinse light is normally set to "spray rinse", this means the machine will pump out the water, spin at medium speed then pulse cold water into the machine, this occurs for about 2 mins, then the machine will spin out, and advance for the final rinse which is a deep rinse.

Posted on Sep 23, 2008

cbrown801

Lisa Brown

  • 3 Answers

SOURCE: washer wil not spin or drain out after cycle completed

sounds like drain is plugged. this is a fairly easy fix,and you actually get paid to do it. unscrew the bottom panel of your washer should be 3 screws on the very bottom then you will see a white plug that is about 2 1/2" unscrew it (make sure you have a bowl under it water will leak ) and pull it out. this is where you get paid you will find all kinds of change and junk just clean it out reinstall and your clothes will be a lot drier after the spin cycle

Posted on Mar 30, 2009

Anonymous

  • 1 Answer

SOURCE: asko 10625 will not spin

it is probably the belt, take off the back of the machine and look at the black rubber belt that spins the cleaning drum. The belts break after about 5 years, you can get a replacement belt at you local Asko dealer, I recall that is was pretty easy to change, like doing a bike chain, Talk to you Asko dealer about how to change it.

Posted on Jul 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore 80 series Model # 110.23832100\r\nthe washer fills up agitates, when finished washing it stops pauses a while then starts to spin, you can hear the water going out put it is like it can't pick up...


Hi

If the washer is not draining then it is due to a clogged drain pump, drain filter or a kinked drain hose. Clean the drain hose, inspect if the drain hose is plugged. Also check the connection to the drain pump and make sure wiring is fine. Check the electrical connections with a multimeter. If it still doesn't work then you would need to replace the drain pump. Hope this helps...please post back for further assistance.

Daniel

Apr 07, 2011 | Kenmore Washing Machines

1 Answer

LED is flashing F3 while load is in the washing machine. It has stopped running. It is full of soapy water. ASCO W6441 Quattro 1400


Hi,

The "F3" for Asko washer`s indicates a problem occurred during pump out or specifically with the pump.

Based on your description of the unit being "full of soapy water" I suspect you have the wrong detergent or too much in the machine. These Asko ( any front load for that matter and some hi efficient top load`s recently ) must be used with lo-sudsing detergent`s only, also known as "H-E" detergent. If the manufacturer`s recommendation to use only "H-E" is not followed the unit will not function properly. ( "H-E" detergent`s do not use nearly as much "soap" as an additive in the detergent thus there should be no or very little suds present with the proper amount, always use half or a third of what is recommended on the detergent container, after all, they are in the business of selling detergent. The more you use is a benefit to them and of little to no consequences...except to you the consumer ) Some symptom`s include not allowing the pump to drain the unit properly, hence creating an error code such as "F3".

You may be able to remedy the error by way of removing the item`s of clothing, add some white vinegar ( this will help neutralize the suds ) and run the washer thru a short wash or rinse cycle. You may need to repeat this procedure to wash away excessive soap buildup in the machine.

You may also need to prewash clothing previously washed with regular detergent or in top load machines to minimize sudsing as well. This is something I suggest to all my customer`s who are new to the front load world.

If this does not remedy the problem and in fact the unit just won`t drain, check the pump for any obstructions in the filter insert/pin trap.

Here`s how to check...

**1. Turn off the power to the machine.

2. Using a flathead screwdriver
or similar item,
gently pry open the
drain pump cover if present on your model.

3. There is always a small amount of water in
the drain pump area. Before you open the drain
cover, place a shallow container, such as a pie pan,
on the floor below the drain to catch the water.

4. Pull the small black drain
hose loose from its position
on the door cover and let
the water drain into the pan.

5. Twist the pin trap cover
counterclockwise and lift it
out.

6. You can now clean out
any grit or small
objects. You should
also clean the pump
rotor at the back of the
pump housing.

7. Replace the drain cover and return the drain hose
to its position on the door.**

These are common issue`s to look for with Asko, or as I alluded to prior any front load machine. You may want to consider calling in an authorized Asko servicer if you are not completely comfortable with any of these suggestions or performing these procedures.

( I don`t know why my font changed nor how to change it back ,sorry not my computer right now it`s a netbook lol )

Hope this help`s solve your problem. If so please take a moment to rate the info I provided. If not let me know if I can assist you further.

Thank you for visiting "fixya" for you Asko inquiries.

Good luck.

macmarkus :)

Mar 23, 2010 | Asko Washing Machines

2 Answers

Water doesn't drain


you could have a bad drain pump.
have you checked the hoses that come from the bottom of the tub to the drain pump for anything that might be stuck in there,also check the hose that comes off the drain pump to the wall and look for an obstruction.

Jan 31, 2010 | Asko W6021 Front Load Washer

1 Answer

I have an asko 11505 clothes washer. For some reason, it is not going through all of the spinning cycle, it spins for a short time, then stops abrutely. I cleaned the coin stop, cleaned out all water...


My Asko 11505 washer fills only a little water then shuts off. If I drain the washer with the drain hose from under the machine, then the machine will start up and fill enough water to fill the hose again, then shut off.

Oct 19, 2009 | Asko Washing Machines

1 Answer

The washing machine stopped on the rinse (6) with an F-3. Now what do I do?


Hi,

"F3" on Asko means the machine detected an interuption in the drain sequence. could be as simple as a coin or some other debris causing the fault, but it may be the pump is faulty as well. first things first.

**UNPLUG the unit from the dryer, or from the wall, which ever applies to your set-up**

in the lower left corner on the front of your washer is a "pin catcher/lint filter" for the pump (a pump insert asko calls it). unscrew this insert, clean out whatever is obstructing the pump and you should be fine to continue. unless the pump itself is at fault. **you will need to drain whatever water is in the unit into a drain, or pan thru the little drain line from the pump (refer to your manual if you have access to it).

hope that helps,

good luck

Sep 28, 2009 | Asko W6021 Front Load Washer

1 Answer

My Asko W6441 front load washer F3 message


Hello. You said that you checked the drain line for obstructions, but did you check the pump? I would remove the hoses from the pump and using a flashlight, look into the suction port on the pump. Check the pump for any obstructions (like the occasional stray sock) and check the pump impellers. Look for broken/missing blades and ensure that the impeller spins freely. If there are missing/broken blades or if you cannot get the impeller to spin freely, the pump is defective. You may have already done this, and if so I apologize. Anyway, hope this helped and best wishes.

Aug 28, 2009 | Asko W6441 Front Load Washer

2 Answers

Washers fine but doesnt drain water and go to rinse cycle


Check the drain hose may be kinked. Washers have been known to eat socks, they go in to the the tub during the spin cycle and down in the pump. If you are so inclined to look dome pumps are clear and you can see the sock. There is a hose clamp to remove and you may be able to remove the sock. Reassemble and test. Remember as always to unplug the washer first before doing any work. This exploded view has a washer and if you hover over the bottom right it will show what the pump looks like.
http://www.repairclinic.com/Washing-Machine-Top-Load-Maytag-Style-Appliance-Diagram Good luck

Aug 21, 2009 | Kenmore 22422 Top Load Washer

1 Answer

Washing machine will not drain


TAKE THE HOSE OFF ON THE BACK {DISCHARGE HOSE} IF THE WATER FLOWS OUT IT IS THE PUMP MOTOR IF IT DOESN'T THERE IS SOMETHING BLOCKING THE OUTLET, SMALL CLOTHING ITEM

May 29, 2009 | Indesit W 123 Front Load Washer

3 Answers

LG Top loader not draining water to rinse and spin


YOU NEED TO CHECK THE WATER PUMP,SO LAY THE MACHINE ALL THE WAY DOWN ON ITS FRONT,NOW YOU HAVE ACCESS TO THE PUMP.Remove any debris that may be lodged inside of it.

Jun 09, 2008 | LG WFT1071TP Top Load Washer

1 Answer

Spin/rinse cycle


find tech sheet at bottom of washer and follow instructions for checking motor controller (at bottom rear)

Apr 13, 2008 | Frigidaire Affinity ATF7000E Front Load...

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Asko Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Joseph Hoffmann

Level 3 Expert

1755 Answers

ROB

Level 3 Expert

858 Answers

Are you an Asko Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...