Question about Hobart Food Mixers

1 Answer

My Hobart A200 lift arm seems frozen. Sat in garage covered.....won’t lift.

Posted by on

  • Jamie Smith
    Jamie Smith May 17, 2018

    Got it. All fixed.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 250 Answers

There are a few retaining screws in the guide's that you can undo to clean the runners. They get gummed up with flour over time. This should help

Posted on May 27, 2018

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 1 Answer

SOURCE: Manual for Hobart Mixer A200

You can go to hobartcorp.com and register for free then you can print or download a parts
manual to help you to do repair. Hobart provide service manual to their technician only.

Posted on Jan 17, 2009

Anonymous

  • 135 Answers

SOURCE: speed reduction of Hobart A200 mixer

Hi Don. If your mixer is hurling honey, you must be very popular in the ant world...Sorry!

The Hobart electric motor on your mixer was designed and engineered to operate on 115-120 volt current and is the most dependable, and capable commercial mixer out there Is it possible for you to use a commercial Imerssion Blender for the first part of your mixing operation. Once your honey thickens a bit perhaps the a200 wouldn't hurl honey. Another consideration would be to either try a different beater or modify the one you have by removing surface area from the beater. If you remove metal, be sure to do it in a balanced fashion to avoid unwanted vibration in the beater. If you're not up to removing metal, take it to a machine shop and they'll do it for you. It probably won't take long, or cost much, and they have the expertise and the equipment to do it properly. If you found this solution helpful, please rate it. Good luck! ricardok45.

Posted on Feb 04, 2009

bigg t

anthony james

  • 640 Answers

SOURCE: on and off switch for hobart stand up mixer a200

I'm a hobart tech---what is the ml number on the data plate?

Posted on Feb 24, 2009

Anonymous

  • 11 Answers

SOURCE: hobart A200 mixer is for our church kitchen. when

Are you still under warranty? If you take the machine apart you could ruin the warranty. First try calling them and telling them it is for a church and a non profit and you had to raise money to purchase what you thought was the best. I would also try cutting the mixture in half because you can always knead the dough slightly. If this is the case then you don't have a powerful enough mixture. If you call them it may make a huge difference.

Posted on Nov 06, 2009

Anonymous

  • 1 Answer

SOURCE: Hobart mixer A200 Rotation

I have a hobart a200 20qt mixer. the flat bitter is scraping the botttom of the bowl. The shaft looks little bend and i think it is and that is what's scraping the bowl at the bottom on one side only. the whole bowl is not being scraped. it used to work like that and now it does not work at all. the motore is running but the gears are not turing the mixer. Before the first geard stoped working but the other two were okay, now none of them work, but the motore is working.

Posted on Nov 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dc-sm168


Hello, Go here for beaters for your mixer: Hobart Mixer Parts Hobart Mixer A200

Jun 02, 2014 | Hobart A200 Stand Mixer

1 Answer

Was just givin a hobart a200 was in a school warehouse for at least 1o years attach.shaft and seals replaced by hobart 6 month before put in storage runs great smooth no gear noise BUT fromm sitting bowel...


Ogrin56,

The problem is in your lift handle cams, you need to take the pedistal apart and clean and grease all the cams. I take them apart and wire brush them and use white lithium grease to keep them from freezing up.

Feb 26, 2011 | Hobart A200 Stand Mixer

1 Answer

Hi, I have a used Hobart A200T and the bowl yoke piece moves up and down slightly, even under a light load. It makes an annoying clanking noise. It's as if a spring somewhere is looser than it should be....


You may be correct about a loose spring. Check this:

Carefully lay the mixer on its back side to access the bottom of the mixer. Remove the cover screen covering the opening in the bottom of the mixer. Using an extension and appropriate socket, be sure the nut of the bowl lift rod is snug, slightly compressing the spring of the bowl lift rod.

Jan 26, 2011 | Hobart A200 Stand Mixer

2 Answers

Loose gear


Lock out-Tagout the machine. Remove the top cover, hold the beater shaft while removing the center shaft nut. Then remove the 4 bolts and and hardware on top of the first(worm) shaft and the second(clutch)shaft. you can gently tap the top cover up with a cold chisel on the upper parts of the housing. It's just a friction fit , aligned on two dowels. Once the cover is off, scoop out the grease, remove the side panel and selector assembly. Try and lift all of the first gear assembly together. the newer ones have a series of rollers and springs, which can be easily reassembled, if you see which way everything was. As you rmove parts, lay them on a clean surface in a row in the position they came out. The selector sleeve is marked TOP, but looking at the 4 drive teeth each side, you will see how it drives 2nd and 3rd gears. The clutch and worm shafts lift out together from slip fit bearings in the housing base.

When reassembling, coat everything with new grease, and run before loading all the grease. If you need to remove anything , you won't be up to your wrists in grease doing it. Once all is good, load the grease in the top hole nearest the motor with it running. The gears will feed the grease as you load the 35 OZ.
If you removed the planetary to remove the center shaft, don't tighten the half nut tight. back it off a half turn and lock it with the acorn nut. Otherwise you will loose first gear from pinch friction.

Sep 14, 2009 | Hobart A200 Stand Mixer

2 Answers

Hobart model a200t not working propery. Just hums when turned on


take top front cover off see if motor is spinning when turned on? hum can come when motor is running or transmision jammed or motor has issue like capsitor bad or start switch inside motor bad.

Jan 03, 2009 | Hobart A200 Stand Mixer

2 Answers

Hobart A200 transmission issues


does not sound good it need to be torn down and checked from here thats more then can be figured out sorry

Nov 26, 2008 | Hobart A200 Stand Mixer

1 Answer

Hobart A200 diagnosis


the first A-200's have a worm gear drive that will slip when old but also when mixing dough somtimes the dough will push the mixer aherad of its self and look like its slowing but its just catching up. if you have a old worm shaft it will have a spring on it is how to tell. it is replaced with a shaft that is all keyed and has no slip or give unless a key shears.
Michael

Nov 25, 2008 | Hobart A200 Stand Mixer

1 Answer

Hobart A200 oil leak


grease coming out the planitary on bottom normally means it needs taken apart completley cleaned out of old grease and new seal and newer stile spacer seal goes around with the O-ring on it. and factory grease. the noise impossble from here to tell.

Sep 10, 2008 | Hobart A200 Stand Mixer

3 Answers

Hobart A 200 Mixer - Lube


HI Joe
I have the wrong greace in my A200 standmixer i need to know what kind and how much to put in gear cace. thank you

Jul 17, 2008 | Hobart A200 Stand Mixer

Not finding what you are looking for?
Food Mixers Logo

Related Topics:

306 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hobart Food Mixers Experts

Ross Keen

Level 3 Expert

1364 Answers

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Bruce Showalter

Level 2 Expert

133 Answers

Are you a Hobart Food Mixer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...