Question about Asko Washing Machines

Open Question

Asko W6551 front loader, program starts, fills up with a little bit of water, then just stops and sits there, no errors, no nothing. Was totally fine last time I used it, and wake up today and this, is there some button I've accidentally pressed or what? Have been fiddling around trying to figure out the time-delay option button, but it makes literally zero sense, either a clock or an hourglass symbol, having it on EITHER does NOTHING though, so quite pointless. Any ideas?! Thanks!!

Posted by on

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 2 Answers

SOURCE: machine wont stop filling with

Same thing happened to my ASKO W600.  Sounds like the water inlet valve is blocked or broken so therefore can't stop the flow of water coming into machine.  Check it out and replace if necessary.

Posted on Nov 03, 2008

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace drum bearing ... in a ASKO W6551 step by step


you need to remove the drum start at the front remove front panel,four screws 2 under front,1 behind soap drawer and the one near the filter,next take door off 4 spring clips on the next panel plus screw on door lock,remove door lock,then undo clamp band,bolt at bottom and remove counter weight panel (heavy).remove stainless steel inner panel,use a screwdriver to loosen,from the back remove drum pulley.the drum will then pull out.replace vseal and bearings.hope this helps

Jun 05, 2010 | Asko WL6511W Front Load Washer

2 Answers

Drum will not spin


Hi,
I am the new owner of a used Asko Cylinda 10504.
The last owner briefly demonstrated the washer starting a wash cycle and entering the agitation cycle of the wash before stopping and pumping the water out and spinning in a final end cycle. I bought it. I had the machine installed turned it on and cannot get it to go through the wash cycle. After starting at #1 it goes through a perpetual spin cycle of sorts--water and soap soaking the drum and laundry but not enough water to fill up half way or less. It stops at number 4 on the program knob sits on a red dot (next to the #4) and does nothing. I then manually move it to the next cycle and it repeats the spin cycle again until I have advanced the program to the end. No wash cycle no rinse cycle. Nothing. When it advances to the red dot I wait for at least 5 minutes before manually advancing the knob. The instructions say that I should get the water pumped out by turning the program knob to #7 or #9 but in both cases it just spins and does no empty or finish in the end spin cycle of several (9?) minutes. Nothing but banging and spinning. The water seems to get into the drum as well as the detergent but nothing else is happening.
No mater where I start the program it spins and sloshes soapy water, pumping almost nothing out.
Any suggestions short of putting it on the curb or paying a kings ransom to fly a tech out to look at it?

MY GUESS.
It seems that it is repeating the same brief cycle over and over. During the move to my house the electronics re set(??!?!?) and now need to be set to the normal mode after being re connected?
Can you help?
Blessings,
Douglas

May 20, 2009 | Asko Washing Machines

1 Answer

Asko w640 has a water inlet fault


Check the drain line to make sure the water does not siphon out as it enters the machine.

Mar 10, 2009 | Asko W640

1 Answer

Machine wont stop filling with water, it just overflows. Machine is an Asko w6551 front loader


Same thing happened to my ASKO W600.  Sounds like the water inlet valve is blocked or broken so therefore can't stop the flow of water coming into machine.  Check it out and replace if necessary.

Oct 30, 2008 | Asko Washing Machines

2 Answers

ASKO w6011 FRONT LOADER


Try to Open the safety compartment using a screwdriver under the wash machine in the front.
Then open the big white knodb this will cause the wate to drain out which is fine.
Then clean this out. Usually you will find coins and stuff here from years of operations from pockets. clear these out and your problem maybe fixed. worked for us

Jun 09, 2008 | Asko W6021 Front Load Washer

1 Answer

Washer filled with water & then stopped & will not work in any cycle.


could be a bad pressure switch did it fill all the way is it a top loader or front loader any noise or nothing

Dec 31, 2007 | Kenmore 24622 Top Load Washer

1 Answer

Asko W6021 Front Loader Washer Problem


the carbon brushs in the motor need replacing,on the w6021 the fault you get is a clicking sound when you press the start button.

Nov 01, 2007 | Asko W6021 Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Asko Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Joseph Hoffmann

Level 3 Expert

1755 Answers

ROB

Level 3 Expert

858 Answers

Are you an Asko Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...