Question about Asko Washing Machines

Open Question

I cannot get the pin trap cover back in to my ASKO washing machine. Is there a trick to it?

2003 ASKO W6761 washing machine. Able to remove pintrap cover to remove coins but now cannot get it to go back in

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 3 Answers

SOURCE: Asko W620 washing machine not spinning

Sounds like the motor brushes need to be cleaned or replaced. Take the back off the washer, remove the motor and gently scrape the excess carbon or debris off the brushes with a pocket knife. I did this and it ran well for about 50 loads before building back up. I am ordering new brushes now because when I checked the brushes last week they were obviously worn more than 4 weeks ago.

Posted on Jan 21, 2008

Ad

Ian Greenland

  • 351 Answers

SOURCE: not just your ordinary pintrap drain problem

check to see if there is a small coin in the grey drain hose that joins the pump also see if theres a coin stuck in the black sump hose to the pump.you will have to remove the front panel first.two screws underneath the front a one under the soap drawer.the paddles pull out put small screwdriver in the middle hole and pull hard toward you,they will come out also blow through drain hose to see if somthing stuck coins act like a valve and cause inttermittent draining problems,also check pump impeller isnt damaged it may look ok(white).hope this helps.

Posted on Mar 26, 2008

Ian Greenland

  • 351 Answers

SOURCE: Asko W6761 Front Loader

check the fuse on the back panel if thats ok check to see where theres power it may be a display board fault.

Posted on Aug 27, 2008

Ian Greenland

  • 351 Answers

SOURCE: Asko W6761 washing machine frozen

it looks like the control board needs replacing the part no is on the board and starts 80,but first can you get into the menu option or has it locked you out

Posted on Aug 28, 2008

Anonymous

  • 1 Answer

SOURCE: open coin trap

use side of spanner to open the circular water drain plug on coin trap, remove all water.
use flat screwdriver to lift yellow tab at top of coin trap whiloe turning coin trap anticlockwise.

Posted on Mar 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Asko w6444 front loader drum vibrating quite loudly. Feet are level. Any suggestions.


Check the 3 transit bolts on the backside of the machine. Should be removed. Could also be a problem with the balancing spring on the top of the drum, so the drum tilts a bit forward, and cause noise

Aug 11, 2013 | Asko W6761 Front Load Washer

1 Answer

What size fuse does asko washing machine take


no size given, but here is the part.
http://www.repairclinic.com/PartDetail/Line-Fuse-and-Holder/8801354/1460992?modelNumber=W6761%2FStainlessSteel

Dec 06, 2012 | Asko Washing Machines

2 Answers

Asko washing machine won't drain.


Further on to this F3 problem I had the issue on model W6461. There is a short cut to the fix, instead of taking off the grey pipe from the drain pump (the hose clips are pre crimped in the factory so as stated above are difficult to remove) try this.
Stages as follows:
1) Open drain pump door (bottom left of machine).
2) Remove black pipe and drain residual water.
3) Unscrew coin trap and remove, use a container to hold the water.
4) Leave the container underneath and make sure you have some towels ready (I didn't at the time)
5) Where the washing machine drain hose connects to the outlet or U bend connector remove this and expose the end.
6) Blow into the drain hose as hard as possible......hopefully the blockage will clear through back the coin trap.

Result:
A large lump of sludge, three of my 5 year olds small counter coins and about a litre of water.

Just ran the machine now and fault cleared.


Good luck

Jurgo

Apr 30, 2010 | Asko W660

1 Answer

I have an asko wm200 washing machine. I have an F3 error, which is stopping me from opening the washer. The washer is also still full of water. Just need to know how to get the door to open and the water...


open the little door at the bottom or remove the toe panel... then there is a coin trap... that will let you remove the water there is a black hose with a plug on the end remove plug and drain the water...by turning it and pulling it you can remove the coin trap and you my be able to remove somthing stuck in it... also there is a red string you can pull it and release the door


Hope it helps if NOT let me know more about your problem... and I will help

Jul 08, 2009 | Asko W6761 Front Load Washer

1 Answer

Asko W6761 - seems fine, starts to fill 40 seconds then stops!


Hello, my W6761 becomes the same. When it happens, you can clear the problem by "soft ware reset". Following is the procedure:
1. Power it on
2. Push Start/Stop buttom 5 times
3. Push "Enter", ">", "<", "Menu" buttons (from right to left)
4. Again, push "Enter", ">", "<", "Menu" buttons
5. Wait for 30 seconds that the above soft ware cycle resets the internal status
6. Power it off and on, again
7. You need to execute above "soft ware reset" within 15 seconds

Start washing and check to see if above reset the problem.
If it does not begin to work, repeat above "soft ware reset" cycle until it begins to work.
My W6761 once needed to repeat above cycle 7 times to solve the problem.
This problem happens in mostly in warmer season, so this will be related with high ambient or water temperature.

ASKO technician may replace the controller but even with the replaced controller, this problem often happens.

Tsunett

Mar 16, 2009 | Asko W6761 Front Load Washer

1 Answer

Asko W6761 Front Loader


check the fuse on the back panel if thats ok check to see where theres power it may be a display board fault.

Aug 27, 2008 | Asko W6761 Front Load Washer

2 Answers

Not just your ordinary pintrap drain problem


check to see if there is a small coin in the grey drain hose that joins the pump also see if theres a coin stuck in the black sump hose to the pump.you will have to remove the front panel first.two screws underneath the front a one under the soap drawer.the paddles pull out put small screwdriver in the middle hole and pull hard toward you,they will come out also blow through drain hose to see if somthing stuck coins act like a valve and cause inttermittent draining problems,also check pump impeller isnt damaged it may look ok(white).hope this helps.

Mar 23, 2008 | Asko W6021 Front Load Washer

3 Answers

Asko W620 washing machine not spinning


Sounds like the motor brushes need to be cleaned or replaced. Take the back off the washer, remove the motor and gently scrape the excess carbon or debris off the brushes with a pocket knife. I did this and it ran well for about 50 loads before building back up. I am ordering new brushes now because when I checked the brushes last week they were obviously worn more than 4 weeks ago.

Dec 11, 2007 | Asko W620

1 Answer

Asko w6761 front loader


you can remove the grey drum paddle to get access to the inner drum stick a small screwdriver in the middle hole of the paddle and pull towards you other wise you would be better getting an ako tech to do it because ther are three panels to remove plus a clamp band.if you havent done one before it can be difficult,also check the pin trap it may have gone in ther(filter bottom left corner)

Oct 10, 2007 | Asko W6761 Front Load Washer

1 Answer

Fault Indication - "Over Flow"


Does manual say to clear drain by running high temp water to clear drain; i dont think so. Now you have to unscrew the back to see where the leak comes from - by pouring plain water into the machine (where u put clothes). Unplug all electrical connections, ie disconnect the machine from the wall socket. Pl post back

Apr 18, 2007 | Asko W6761 Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Asko Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Joseph Hoffmann

Level 3 Expert

1755 Answers

ROB

Level 3 Expert

858 Answers

Are you an Asko Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...