Question about Dual Car Audio & Video

Open Question

Can I replace a dual capacitor set-up in a ceiling fan with a single capacitor? Same UF but missing white wire connection that was on original two wire cap.

Original had single start cap. With red and white wires. Second has two grey and one each brown and green. New one has two grey W/one each red,green and brown.

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
worldvet

Glenn Rogers

  • 859 Answers

SOURCE: Trying to replace 3 speed ceiling fan switch

Hello,

The black goes to the L connection the others are a guess. You can do this two ways. Connect the colored wires in any sequence and then see what switch sequence give you high and lowest, the other one will be medium. Once you determine that, mark the wires with a piece of masking tape as high, medium and low. Otherwise you connect them, turn power on and use a multimeter to see which color gives you the highest voltage and which gives you lowest. Since you aren't comfortable using live wires and a meter, go with the first option and use the process of elimination to find the wires giving you the speeds you need to find the highest and lowest. Next, you need to determine how your switch sequence works. First pull has to give you highest speed. so you may end up wiring them in reverse if your first attempt is backwards. There is a reason the first pull needs to be highest, it powers up the motor so you can then chose a lower setting. A low setting first will over tax your motor and wear it out eventually as it has to work harder at first.

Let me know if you need further clarification and perhaps this is all you need to get fixed.

Regards,
Worldvet
ps I checked on the Internet of a wiring diagram and I bet you did tok all to no avail.

Posted on May 27, 2008

Ad

Anonymous

  • 254 Answers

SOURCE: HELP!!! Help wiring new motor for CKL60-1

  1. This is what your wiring should look like if you are using two caps. then you should be using a potential relay as well. This is the diagram for using a potential relay. Hope it helps you.
Thank Youe461749.jpeg

Posted on Aug 28, 2008

erpaalai

Eric Duda

  • 999 Answers

SOURCE: wiring a 220v single phase motor and capacitor

Black and white are usually power. an ohmmeter will confirm. Brown are for capacitors. There is almost always a diagram on the motor someplace. Eric

Posted on Jun 17, 2009

christian nielsen

  • 358 Answers

SOURCE: how to wire motor to dual run capacitor

The easiest way to do it is to get a capacitor just for the fan motor (in the motor tag you can read what size cap. you need , maybe 5uf or 7.5 uf) and put the two brown wires on each side of the capacitor and the lines (probably white and black) to the contactor.

Posted on Sep 27, 2009

Zaraki

  • 834 Answers

SOURCE: I purchased a ceiling fan

That is kinda confusing, but it sounds like the blue wire for the light kit should also be connected together with the red supply wire for the fan motor from the ceiling wires, and not the capped black wire. That is if the two wires to the fan motor are the white and red wires from the ceiling. Normally the white wire is a neutral wire and the black is the field wire and they both are alternating current "hot" wires, and the green wires are grounded to earth ground only.

Let me know if I understood that right about the wires from the ceiling, and let me know if you require any further assistance.




See if this diagram is correct

f1d3586.jpg

Posted on Sep 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 3 ton Bryant split unit I'M trying to rewire.


what colors are landed where on the tstat? and does the tstat wire that goes BOTH inside and outside have the same colors. also why are you in this situation, has everything been unhooked?

If you need further help, reach me via phone at https://www.6ya.com/expert/thomas_092728000e6acb79

Feb 09, 2018 | Heating & Cooling

1 Answer

I have a 55/15 uf dual cap that I want to replace with two single caps. One 55 uf and one 15 uf. How do I wire the caps?


You'll need a jumper to connect the common leads to 1 side of both caps. Then put the 55 µf and 15 µf leads on the respective caps. A/C caps have no polarity.

May 12, 2016 | Heating & Cooling

1 Answer

Wiring a d2 eberspacher diesel night heater up


how much it coast black & decker Heater product model no . or07d
thank you

Dec 22, 2013 | Heating & Cooling

1 Answer

I'm trying to hook up a Kenwood kdc x492 to a 96


Battery is yellow
Accessory is white/red
Ground is black
Illumination is red/black
Power antenna is yellow/white
LF speaker +blue/green - grey/black
RF speaker +red/green - brown/black
LR speaker +blue/yellow -grey/white
RR speaker+red/yellow -brown/white

Feb 11, 2013 | Car Audio & Video

1 Answer

Belling cooker d841 top oven


The US National Electrical Code only mandates white (or grey) for the neutral power conductor and bare copper, green, or green with yellow stripes for the protective ground. Power will generally be black or red. 3 phase power will have three colored lines, the first is generally black or brown, the second red or orange, and the third blue or yellow..
i,e,
Yellow/Green is Earth so 'E'. Brown is live so 'L', and Blue is neutral so 'N'.

May 08, 2012 | Belling XOU174 Electric Single Oven

1 Answer

I have a single pole switch that currently controls a bedroom outlet. i am installing a fan and light in the bedroom. i have a new triple switch that i want to control the existing outlet, the fan and the...


Wiring is not fully described: Location of hot wire and neutral wire from breaker box are unknown.
If Hot wire arrives in ceiling box first, the switch box will not have white neutral wires that are twisted together and covered with wire nut. Neutrals will be in ceiling box.

What is known: You are replacing single pole switch attached to one 14-2 wire going to light.
You are replacing light with a fan-light and replacing switch with a 3-pole TM8111 switch.
You have replaced 14-2 wire with 12-3 wire.

TM8111 wiring shows following link:
http://waterheatertimer.org/images/TM8111-switch-wiring-500.jpg
Fan pull-chain wiring shows following link:
http://waterheatertimer.org/images/Fan-motor-1-344.jpg
Assume neutrals in ceiling box.
Assume Hot wire in ceiling box: Connect 12-3 black wire to black Hot wire. Connect 12-3 white wire to black wire on light. Connect 12-3 red to red wire on fan.
White neutral from fan and white neutral form light connect to other white neutral wires and covered with wire nut.
Wiring at switch:
Black Hot wire from ceiling box connects to A COM terminal.
White wire to ceiling light connects to A SP2
Red wire to fan connects to A SP1

Jun 21, 2011 | Pass & Seymour Legrand TM8111 Three Single...

2 Answers

What does the stereo colors stand for on an 1992 crown victoria Red, black, Grey/blue, yellow/black, white/purple, green/black ,blue/red, orange/green, white/green, blue/white, brown/yellow,...


Red = ground
black = ground
Grey/blue = Left rear (+)
yellow/black = ignition 12v
white/purple = right rear (-)
green/black = (could this be green / violet?) than it is 12v constant
blue/red = illumination
orange/green = left front (+)
white/green = right front (-)
blue/white = left front (-)
brown/yellow = left rear (tan / yellow) (-)
green/orange = right front (+)
orange/red = right rear (+)
blue = not used

Nov 10, 2010 | Ford Car Audio & Video

1 Answer

Colour codes for 83 corona, wiring stereo the colours are grey/black grey/red Brown Purple/green Grey Blue/yellow blue white/black any help would be great thanks!


Hello! I'm having a hard time reading your colors...So, I'll give you the 1983 Corona wiring...

POWER

Constant +12= Blue/Yellow Switched +12= Gray
Ground= Brown Antenna= Black/Red
Illumination= Green


SPEAKERS

FR+ Light Green
FR- Blue
FL+ Pink
FL- Purple
RR+ Red
RR- White
RL+ Black
RL- Yellow


Guru...........Saailer


I’m happy to help further over the phone at https://www.6ya.com/expert/david_6df67de3b14de867

May 30, 2010 | Pioneer AVH-P5700DVD Car DVD Player

1 Answer

I have a fairly old panasonic car stereo/cd changer. i just need the wiring diagram for it. what color equals what? i typed in the model number but nothing turns up. . . i had to replace the old system,...


Here is the Colors of the Cars factory harness

Constant 12V+ Red Switched 12V+ Red/White Ground Black Illumination n/a Dimmer Orange/White Antenna Trigger Yellow Antenna Right Front Front Speakers 3 1/2" Dash Left Front (+) Green Left Front (-) Green/Yellow Right Front (+) Purple Right Front (-) Purple/Yellow Rear Speakers 6" x 9" Rear Deck Left Rear (+) Brown Left Rear (-) Brown/Yellow Right Rear (+) Blue/Red Right Rear (-) Blue/White


And Here is the Chart for the radios wiring

Red 12V+ Switched power
Grey Right front speaker +
Grey with black stripe right front-
White left front +
white with black stripe l/f -
Purple R/R +
Purple with black stripe R/R -
Green l/r +
green with stripe l/r -
Black ground
orange illumination
yellow constant power

Apr 07, 2010 | Car Audio & Video

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

231 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dual Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

5013 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8981 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Dual Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...