Question about Asko Washing Machines

Open Question

I cannot close the door on asko 6324. The stop button with the key icon is blinking

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

prem mathew

  • 1294 Answers

SOURCE: Asko washing machine door not closing

Changing the door lock is one of the easiest things to do in a washing machine. Just note which wires go where & get a new door switch.

Posted on Jun 11, 2007

Ad

Anonymous

  • 1 Answer

SOURCE: Quick Rinsw button blinking

I may have fixed my similar problem- I opened up the machine to get access to the control panel as tech17 advised- then in addition to disconnecting the mylar ribbon, I disconnected all the connections to the control panel.... keep in mind to ensure not to confuse any of the connectors you disconnect. Running a cycle at this time... seems as if working.. can't tell if water is running or just the motor- -- HA! -- i confirmed no water being pumped in.... We then found a float switch (Item 30 on schematic) that got loose from its casing on the front interior right lower side... we put that switch into its proper place and now ALL IS WELL!!!! Yippee!!!

Posted on Feb 04, 2009

Paul Hutchinson

  • 909 Answers

SOURCE: red light next to hazard light button blinks when

If it's a tiny red L.E.D. like a car alarm indicator, then it's to let you know the imobilizer is set, factory fitted and set to work from your key sensor(built into the ignition switch and key)

Posted on Jul 19, 2009

Anonymous

  • 2 Answers

SOURCE: Lights on the Asko D1996 keep blinking

This depends on the blinking pattern. Of the eight lights on the panel, if the four on the left blink on and then the right four lights blink on as the left ones go off, and keep blinking back and forth, that just means the mode has been set and the Start button pressed. After closing the door it should just continue on wherever it is in the cycle. (This is normal operation).
If you hold down the Start button, this resets the dishwasher. If you then close the door, nothing will happen because it thinks it's done.
If the lights are blinking in a different pattern, such as they all blink on and off in unison, that indicates an error condition and needs to be diagnosed. If the pump is not running constantly, then at least it's not because water is leaking out somewhere.

Posted on Sep 18, 2009

Don Maggard

  • 3197 Answers

SOURCE: Access Master 1/3 HP garage door does not close, blinks

Most likely your door sensors are out of alignment. Make sure they are pointed directly at one another.

Posted on Apr 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hazard lights flashing and alarm sounding. How do I stop these?


Every car brand and model has its procedure to stop the flashing light and alarm sounding.
But still the common procedure is Make sure boot and bonnet are closed properly.

It can also be a switch, but check your alarm by locking yourself inside the car, and then press the close button on the key 2 times repeatedly until the lock control on the door doesn't make anything. Then open the door by pushing the lever or open the hood . If the horn sounds and the lights blink your alarm is ok , if only the lights blink you should take it to dealer. You can stop the hazard lights and horn sound by pressing the unlock button on the key.

May 12, 2016 | Cars & Trucks

1 Answer

I'm trying to start the asko washer for the first time and I can't get the door to lock. the start button is blinking??


HI there, the door on my front loader was very hard to close, but the service people told me to close it really hard - slam it! and it has been fine ever since.

Jan 02, 2011 | Asko W6021 Front Load Washer

1 Answer

My wired key pad in the garage opens and closes the door but the buttom keeps blinking fast. My two car remotes stopped working. My remote key pad on the house works. Whats with the fast blinking and...


Press and hold for 3 seconds the button on the wall control that has an icon of a lock. The light should quit blinking and your remotes will once again work. Holding that button for 3 seconds toggles your openers vacation mode.

Nov 23, 2009 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

HI, the wall remote for my 976LM light is blinking but if I push the open/close button it does open the door although the car remote won't open it, i've replaced batteries but it doesn't help. Any advice?


One of the buttons on your wall control has an icon of a lock. Press and hold this for 3 seconds and release. The blinking should stop and your remote should work.

Jun 29, 2009 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

Sear garage door wall mount contol light keeps blinking


Hold the button with the lock icon in for 3 seconds. This should toggle the unit off vacation mode and your remotes will work.

May 31, 2009 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

Asko D3250 not working


If the first start button is blinking then there is a door error...the door switch is not closing... to repair

1) turn off the power at the breaker...
2 ) remove screws in the door T20
3) remove contol panel (slide up)
4) place wire tie behind micro switch on door latch...
5) replace door latch and door.

Hope it helps....If NOT let me know more about your problem ... I will Help

Nov 25, 2008 | Asko 24 in. D3250 Built-in Dishwasher

1 Answer

Lights on the Asko D1996 keep blinking


This depends on the blinking pattern. Of the eight lights on the panel, if the four on the left blink on and then the right four lights blink on as the left ones go off, and keep blinking back and forth, that just means the mode has been set and the Start button pressed. After closing the door it should just continue on wherever it is in the cycle. (This is normal operation).
If you hold down the Start button, this resets the dishwasher. If you then close the door, nothing will happen because it thinks it's done.
If the lights are blinking in a different pattern, such as they all blink on and off in unison, that indicates an error condition and needs to be diagnosed. If the pump is not running constantly, then at least it's not because water is leaking out somewhere.

Sep 23, 2008 | Asko D1996SS Built-in Dishwasher

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Asko Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Joseph Hoffmann

Level 3 Expert

1755 Answers

ROB

Level 3 Expert

858 Answers

Are you an Asko Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...