Question about Hardware & Accessories

Open Question

How to reset timer back to 10 on a z851m because i ran out of the 10 digit pin number.

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I ran out of attempts to unlock the sterio on 2000 astra,what do i do now.any help would be great.

have you tried this?
Common problem. The safe message comes up when someone has input the wrong code.

There is an internal reset timer between each incorrect code input, this only starts to count down when theradio is powered up. Turn the power off before the timer runs down and you have to start again!

After the 3rd incorrect code you wait 10 mins, and then it doubles each time up to 640 mins for the 9th incorrect code!!

Simplest answer is drive around for a while (don't stall it!) until the display changes to 1 number followed by ----

Now simply press the number 1 on the radio until you get the first digit, it cycles round so if you miss the number you want just keep going until it comes round again.
Now use button number 2 for the second number, button 3 for the 3rd and button 4 for the fourth.

When you have the correct code, press and hold the AS button until you hear a bleep. Now it should be working.
Hope this helps.

Apr 30, 2018 | Cars & Trucks

2 Answers

How do I change from a password back to a pin in windows 10?

When you upgrade to Windows 10, it copies over all of your previous settings. So if you were using a PIN at the time of the upgrade, it should ask for a PIN afterwards. If it is asking for a password now, someone changed something. I have a laptop that I just upgraded and the PIN login is still there. If you don't know the password, and don't have a password reset disk, you are in trouble.

Aug 05, 2015 | Computers & Internet

1 Answer

How to wire koyo timer kt-v4s-c-d

Koyo kt-v4s-c-d is a 12-24Volt DC pin timer.
Timer mounts in a pin base, and wires are connected to numbered screw terminals on the base.
Timer has 12 pins, and is installed onto 12 pin base.
The base terminals are labeled 1 2 3 4 5 6 7 8 9 10 11 12
The 12-24V DC input voltage connects to terminals 11 and 12, and powers the timer mechanism. Positive to terminal 11, and negative to terminal 12.
The other terminals are dry, and receive no power when input is connected to 11 and 12, except the illustration seems to show the timer will electrically connect terminal 5 and negative charged terminal 12. Use multimeter to check each terminal after power is applied.

COM terminal is 8. Run jumper wire from one of the input terminals to terminal 8. When timer is OFF, then NC terminal 9 has power output. When timer is ON, then NO terminal 10 has output.
Timer functions are set using 8 dip switches.
Copy following link for some illustrations.
Copy following link for timer manual.

If you need further help, I’m available over the phone at

Jul 12, 2012 | Hardware & Accessories

2 Answers

I forget my password i enter 10 times will it shut down will my phone still work all info remove

Tounlock cell phone Password:Instructions
Enter the last four digits of your phone number on yourcell phone PIN screen. Enter 9999, and if that doesn't work try 1111, and ifthat doesn't work try other 4 digit numbers you may have entered. Shut off your cell phone, take off the back of your phoneand pull out the battery. Record the IMEI number which is under the battery.Re-insert the battery and power on the phone. Enter the last 4 digits of theIMEI number on the PIN entry screen. Callyour service provider and request the unlock PIN. You will have to prove youare a customer by stating your cell phone number, addressand social security number. Turn off your phone. Hold thekeys "3," "*" and "Call" and switch the phone on.Hold the three buttons down until the word "Formatting..." appears onthe screen. This should reset the phone lock code. Read more: How to Unlock a Cell Phone Password ' eHow.com

Dec 31, 2010 | RIM BlackBerry Bold 9000 Smartphone

1 Answer

How do I set the time on the 61048 SUNBEAM DIGITAL TIMER

This is a countdown-type timer, for precise cooking times, etc. Press hour and minute buttons to set time.
Press start button to begin countdown.
Press hour and minute buttons same time to reset timer.
Timer beeps each 5 and 10 minute intervals during countdown.
This timer does not connect to any electrical device, has a magnet on back, and has internal battery operated.

For large image of timer:

Nov 06, 2010 | Sunbeam 6 Robinson Home Digital Timer

1 Answer

I have a holiday living power stake timer, how do i program it?

I have the directions for this item and tried to paste them here, but exceeded the amount of space allowed. Will send in several replies. FIRST:


MODEL #LW28080 ITEM #0050024


NOTE: To set up Timer for the first time, plug in the timer for 10 minutes, then insert a sharp pointed object or opened paper clip into the pin hole marked "RESET" to clear all settings.


1. Press the CLOCK button.

2. Press the DAY button to set the current day of the week.

3. Press the HOUR button to set the current hour. Be sure to take note of AM / PM.

4. Press the MIN button to set the current minute.

5. Press the ENTER button to finish setting the time.

Note: If you do not touch any buttons for 10 seconds, it will automatically save the time.

Continue to Digital Timer Mode or Photocell Timer mode below.

To have your lights turn on and off at specific times throughout the week, choose Digital Timer Mode.

To have your lights turn on every day at dusk and off at dawn or after 1 - 12 hours, choose Photocell Timer Mode.

Nov 21, 2009 | House Brand Hardware & Accessories

4 Answers

Blue Hat Bank

Type in the code 1234 ENTER then enter your child's new pin.

Pax, Moncia

Jan 04, 2009 | Blue Microphones Blue Hat Little Shots...

1 Answer

Cannot reset clock on my electric stove after a power failure!

Unplug the stove for 10 minutes, then plug it back in.
This should resolve your problem...

Nov 20, 2008 | General Electric Stove/Oven/Range Chrome...

5 Answers

Gigaset se568 siemens wireless Security setting

i have a little problem with my siemens gigaset SE568, here all led lights are glowing except the internet, i checked my net connection with another modem and the result was positive but what is the problem here i can't figure out,please help me,rahat

Jul 27, 2008 | Siemens SpeedStream Modem (4100) (SS4100)

2 Answers

Intel PRO/Wireless 2011 LAN Access Point (WEAP2011EU)

Usually there is a paper clip sized hole in the back of the WAP that you insert a pin or paper clip into for 10 seconds.

Jun 09, 2007 | Intel PRO/Wireless 2011 LAN Access Point

Not finding what you are looking for?
Hardware & Accessories Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hardware & Accessories Experts

Gene Haynes

Level 3 Expert

5391 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Brad Brown

Level 3 Expert

18157 Answers

Are you a Hardware and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides