Question about Timex Watches

Open Question

Timex t45221 analog hands intermittantly stop and digital display and buttons all work and battery replacement

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

SOURCE: not again . . .

Pushing all the buttons at the same time you resets the digital functions. You'll have to reset the time and date, but it will all work again. I don't know why the watch freezes up, but pushing all the buttons at least resets it. I like my watch and this quirk is an annoyance, but it's livable after finding this solution.

Posted on Aug 11, 2007

Ad

Anonymous

  • 2 Answers

SOURCE: analog clock not in sync with digital clock

This problem may be due to your analog hands being improperly zeroed. To find out, try this: 1. Put the watch in chronograph mode by rotating the crowon in its normal position to "chr" 2. Pull out the crown two clicks. This should cause all of the hands to point to zero. If you do this and your minute hand points to 1 o'clock, or five minutes, you will know that this is the problem. If this is the problem, you can can correct it by zeroing the hands as follows: 1. Put the watch in chronograph mode by rotating the crowon in its normal position to "chr" 2. Pull out the crown two clicks. This should cause all of the hands to point to zero, or close to it. You should also notice the letters "HR" in the lefthand digital display. This allows you to move the hour hand by rotating the crown. If the hour hand is not pointing at 12 o'clock, rotate it so that it does. 3. Push the top button once. The letters "MIN" should appear in the lefthand digital display. This allows you to move the minute hand on the large dial, and the minute and hour hands on the small UTC dial. Rotate the crown so that the minute hand points directly to 12 o'clock. 4. Push the top button again. The letters "SEC" should appear in the lefthand digital display. Rotate the crown to point the second hand directly at 12 o'clock. 5. Push the crown back into its normal position. Set the digiatl time and date in your tie zone, and your analog hands should match the digital read-out. If the zeroing of the hands is not the problem, I don't know what is wrong with the watch.

Posted on Sep 27, 2007

Anonymous

  • 14 Answers

SOURCE: Timex Ironman

Please press all pusher at same time, it will restart the ic, it's just like to restart your computer.

Thanks

Tsai

Posted on Jan 27, 2008

Anonymous

  • 3 Answers

SOURCE: Fossil Big Tic Watch - setting the correct time on the digital display

The watch is scrolling through the seconds, and is not something that needs to be set. If there is a bottom it is only there to change the way the seconds are scrolling? There are many different types of these, but most are just standard seconds.

Posted on Apr 06, 2008

escapement

Arturs Kalnins

  • 2338 Answers

SOURCE: Timex IndiGlo Ironman Triathlon - bell stopped working

You have lost the coilspring wich connects the watch mechanics with the speaker integrated in watch caseback. This is why you do not hear any sound but still can see the icon.
Check the area where you made the battery replacement very carefully- you may find that tiny spring. Use the magnet if necessary.
If you can not find it, go to the nearest watchmakers shop and ask to supply the new coilspring.
Do not forget to rate, please.

Posted on Feb 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Back has NO screws. How do I easily remove it to replace the two batteries?


Hi, You may know that this watch runs on two batteries, one for digital display and another for analog hands.
If the analog hands stop working all you need to do is to replace the battery and please replace both at the same time since the band and cover take some effort to remove.
You need to take off the both bands first to access the back side than the back cover with a small knife..
Just in case,if you need the user manual here is the link.
Timex watch: http://www.timex.com/info/Product_Instruction_Guides_Downloads .
Take care..
Regards

Jun 14, 2011 | Timex T56381 42 Lap Ironman Triathlon...

1 Answer

I have a Timex Ironman T563719J. The digital clock is working, but the analog portion has stopped. Any ideas?


There are two batteries in the watch. One for the digital watch and the other for the analog watch. The battery for the analog side probably needs changing but when the back is opened, you might as well change both batteries.

Jan 18, 2011 | Timex Ironman T56371 Wrist Watch

1 Answer

Hello ,,, I changed the battery in my Timex Indiglo and now just the light is working but not the minute hand or time hands. How do I fix this I have tried two batteries already?


Inside the battery compartment, you will see the battery is held down by a clip. Carefully remove the clip and eject the battery. Insert the new battery and replace the clip. If the battery clamp indicates you should do so, quickly press the reset button twice. Then reattach the back of the watch. If the watch display remains off after replacing the battery, press all buttons at the same time to reset the display.

Jul 23, 2010 | Timex 27191 Wristwatch

1 Answer

Analog second hand freezes periodicaly, digital clock works fine


mcdevito75 here, Sounds like the seconds hand is bent and hanging up on the face. See the repair service directory her at fix ya, bottom of the page click on repair service directory the watches.

Jun 24, 2010 | Timex Expedition 84601 Wristwatch

1 Answer

Analog hands don't move to keep time, all digital functions and displays work.


I think you mean that the hands do not indicate the same time as the digital display. If this is the case,then the hands can be adjusted.

You can get instructions on how to do this from the Timex web site "timex.com".

At the bottom of the screen click on "manuals/downloads", then on "product
manual download"

Enter your watch type in the search box and click on "search"

Mar 01, 2010 | Timex Ironman Triathlon Solar Watch T5G691

1 Answer

The hour/minute/second hands on my Timex Ironman not moving


It could have 2 batteries! 1.5 volt for analog and lithium for digital! Take it to a reputable watch repair business and let them check! :-)

Good luck!

Jan 09, 2010 | Timex Ironman Triathlon 50 Lap Digital...

1 Answer

I cant get the hands to move on my iron man 42 lap dual tech watch


This watch has two batteries in it, one for the digital display and one for the analog movement. Chances are you just need to replace the analog battery, which is under the larger digital battery.

Aug 15, 2009 | Timex Ironman Triathlon 42 Lap Combo Dual...

1 Answer

The hands don't work?


Check out if you have two batteries in your watch - one for LED display, another for analog movement.
If there is only one battery, your watch has a mechanical fault and you will need help of a watchmaker.

Rate, please.

Jul 28, 2009 | Timex Expedition 84601 Wristwatch

Not finding what you are looking for?
Watches Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Timex Watches Experts

Janelle Schoonover
Janelle Schoonover

Level 3 Expert

841 Answers

MrFixitSTTL

Level 3 Expert

320 Answers

pacdave

Level 2 Expert

104 Answers

Are you a Timex Watch Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...