Question about Jandy Pool & Spa

Open Question

My Jandy pool pump has a keyboard locked display and wont allow input! we've reset breaker and still no response

Posted by on


6 Suggested Answers


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


albert getty

  • 547 Answers

SOURCE: Pool pump breaker keeps tripping

should be a 60 amp breaker

Posted on Feb 19, 2009



  • 2 Answers

SOURCE: Rule H53sp-24 pool cover pump trips GFI breaker

GFI devices are prone to degrade over time. Also, when used outdoors there are additional moisture issues that may cause sufficient current leakage to trip the breaker.

I had a similar problem this Spring. I was using a 20 amp GFI "master" outlet that protected two additional outlets 'downstream' of it (wired to the 'load' terminals on the GFI outlet- I'd have the check the doc. to see what terminology was used here). The pump was plugged into one of the downstream outlets.

Replacing the GFI seemed to solve the problem. I did ante up $20 for an 'outdoor' model of the 20 amp GFI unit, several bucks more than the standard 'indoor' unit - have no ideal if that represented additional value or not.

Note also, that this is the third such pump I have used for my pool cover. The other two failed to come on at all after about a year's use. The mfg replaced them under warranty (I may have had to send back the old pump - I forget!).


Posted on Apr 19, 2009


  • 16 Answers

SOURCE: Jandy pool pump will not prime it is a Jandy plus HP model PHPM 2.0

make sure pool is full of water
check skimmer weir doors and make sure not stuck in up position
fill pump basket with water and try to prime

if that doesn't work

replace diffuser oring

Posted on Jan 16, 2010


adam hudson

  • 310 Answers

SOURCE: I purchased an Intex 1500

They are so cheap, just buy a new one. Intex filters and pumps are essentially "disposable" products, and typically dont last more than 2 years

Posted on Apr 22, 2011


John Prohaska

  • 1378 Answers

SOURCE: Jandy Lite 2 pool heater

Thank you for posting your question here on

Page 34 and 35 of your manual, found here, describe FL0 as a flow issue most likely caused by dirty filters. Depending on the type of filter you have a good cleaning/backwash will usually remedy that. It is also possible the unit's pressure switch, which senses water flow and therefore reacts to dirty filters when present, may have failed, especially if you winterize the heater in a cold climate and leave water in the switch which can burst the diaphragm inside.

Start with cleaning the filter. If the heater still won't fire jump out the pressure switch while the pump is running to confirm the part is the problem. Assuming it is replacing it with a new pressure switch which should be under $75. The part number can be found in the rear of the manual.

If this answer does not fix your problem, please comment with additional details prior to rating the answer. You may also contact me thru our website at Positive feedback is appreciated once your problem is solved!


Posted on Apr 29, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Jandy Aqualinks not turning on my waterfall or fountain in the pool and 3 out of 4 of my hot tub jets. How do I re-set or repair

Turning off the power and then back on will do a simple reset. Resetting your jandy will probably not fix your issue. The issue seems more like a bad relay or bad pump or the breaker for the pump may be tripped.

Jun 18, 2017 | Jandy Pool & Spa

1 Answer

My jandy control panel is locked. how do I get it unlocked

About 4,480 results (0.49 seconds) Search Results

    [PDF]AquaLink RS All Button and OneTouch ... - Jandy
    Jandy Valve Actuator . .... If power is then interrupted, the controller will lock up. ...process, which can display its current status on the indoor control panel. Use the following steps to get to this "diagnostics" information: ...... lect Device to unlock.

    [PDF]Jandy Legacy WLRZ Control Quick Start Guide
    The Legacy WLRZ will heat the pool or spa only when the filtration system is running and the ... DISPLAY LIGHT: Controller lights can be set ON, OFF, or to ... Make sure the control is in the ON mode ... To unlock, press and hold the up and.

    Clock" Mode; Locking/unlocking The Keypad; Remote ... > ... > LJ > Installation and operation manual
    Jandy LJ Manual Online: Clock'' Mode, Locking/unlocking The Keypad, Remote Control Operation, ... display of the controller will show the time set for the.

    Jandy AQUALINK RS TELELINK KIT Locked - Questions ... > ... > Jandy > Jandy AQUALINK RS TELELINK KIT

Feb 03, 2016 | Jandy Pool & Spa

1 Answer

Reset Jandy PS6, still flashing red and green

turn off heater if ok then replace ignitor if not keep removing auxs until stops blowing breaker

Apr 02, 2014 | Jandy Aqualink Pda Ps6 Wireless Handheld...

1 Answer

How to turn on the jet sprayers on side of our pool?

turn each one of the auxs off one at a time remember which one it is then label it if the pump wont shut off then start turning off breakers until it goes off if you turn the breaker back on and it does the same bad relay

May 12, 2013 | Jandy Pool & Spa

1 Answer

Is there a reset button for a jandy stealth 1.5HP pool pump

it kicks out breaker try turning the motor shaft if still doesnt work need new motor

Jun 27, 2012 | Jandy Stealth 1.5 HP UR Pool Pump SHPM1.5...

1 Answer

Why is my Jandy Lite 2 Pool Heater Tripping the Circuit Breaker

shorted ignitor remove the ignitor leads and see if it still trips if it doesnt trip replace the ignitor

May 17, 2012 | Jandy Laars Lite2 - 125,000 BTU Propane...

1 Answer

I have a Jandy stealth series pump and this morning it was not running. The breaker was tripped and when I reset it and turned it on the motor only hums for a few seconds and then the breaker trips...

This sounds like the motor has seized up. You will most likely need to replace at least the motor and maybe the complete pump assembly.
You can take the pump into a local motor shop and see if they can rebuild the motor for you.

US Parts Center

Aug 21, 2011 | Jandy Stealth 2 HP UR Pool Pump SHPM2.0...

1 Answer

My Jandy rs all button says the pump is off but the pump stays on. This has happened before and it seems to reset its self or after i turn the pump breaker off it resets. What is going on?

Very odd.

I would suspect a bad relay.

Go to the outside power center located at the equipment. Press the mode button until the "Service" light is on. Now press the filter pump button. Turn it off and on several times to make sure the relay is working correctly. If not, replace the relay.

If this is not the problem then I would reset the board at the power center by pressing the recessed "Reset" button with the tip of a pencil or pen.

If this does not work, you could call Jandy and have them flash your board with the newest software.

Apr 16, 2011 | Jandy Aqualink - Rs24 One Touch Pool / Spa...

1 Answer

My Jandy pump is not working. The breaker was thrown and I reset and it's getting power. Is the pump gone or is there another option.

if pops breaker need new pump motor if it doesnt pop breaker check voltage at pumpmotor if voltage bad motor

Feb 13, 2011 | Jandy Pool & Spa

Not finding what you are looking for?
Pool & Spa Logo

Related Topics:

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jandy Pool & Spa Experts

David Spradling
David Spradling

Level 3 Expert

10391 Answers

Bill Jordan

Level 2 Expert

375 Answers

Steve Slater

Level 2 Expert

72 Answers

Are you a Jandy Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides