Question about Hobart Dishwashers

Open Question

Im having a problem with a Hobart Am15 the rinse feeder wire J1-2 is causing a clicking noise on relay and rinse signal not to work. D7 flashes on the control board

Posted by on

Ad

5 Suggested Answers

bigg t

anthony james

  • 640 Answers

SOURCE: what is p3 code on hobart am15 dishwasher

It means that the final rinse thermistor is bad.Your not getting 180 degrees---right?Its located on the booster and costs about $65.I work for hobart.Any ?

Posted on Jan 25, 2009

Ad

Anonymous

  • 90 Answers

SOURCE: clicking flashing relay

sounds like a poor connection in the fuse box, or a bad ground.

Posted on Jan 26, 2009

Ad
Rebgagnon

Mike Gagnon

  • 382 Answers

SOURCE: flashing relay clicking

If your parking lights are flashing also, I would have to guess that the battery has been disconnected recently. If so there is a small, 4" x4" box on drivers side under dash by colomn that has a small red button on it. Push this button for a few secounds and that should fix your problem. Hope this helps and have a good day.

Posted on Jan 31, 2009

luxur4

Ron Jones

  • 92 Answers

SOURCE: hobart handler 140 will not feed wire

A schematic would certainly help, give Hobart a call and ask for a wiring diagram. or manual. Hobart are very helpful and may even give you guidance, you may have to pay the postage, they usually fax these documents so it will not cost you anything.

Posted on Feb 20, 2009

shane covert

  • 225 Answers

SOURCE: relay clicks, but wire feed motor wont operate

check for power to drive motor,if power is there when you pull gun trigger then motor is bad.if no power look for bad wire connections then relay.

Posted on Jul 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi i am getting a P1 error on a HOBART AM15 ELECTRIC DISHWASHER


Most likely sump temperature probe needs replacing.

Oct 17, 2018 | Hobart Dishwashers

1 Answer

Hobart AM15 Rinse signal (chemical) Continuous 480 volt even during wash cycle or when sitting idle.


A constant electric supply normally means the relay that switches the component is faulty. This would normally be the timer or relay board, depending on how it is switched

Jan 09, 2018 | Hobart Dishwashers

1 Answer

Water continues coming


Hobart ' Undercounter Dishwashers, Commercial ...

www.hobartcorp.com/.../commercial.../undercounters...

Hobart CorporationGlasswasher ... The LXe undercounter is ENERGY STAR® qualified, uses only .74 gallons of water per cycle and features new Smart Display technology to eliminate error codes. Loading... Highlights: Hobart undercounter dish machines are the most popular in the industry, keeping reputations spotless all over the world.

Advansys LXe Undercounter ' Hobart

www.hobartcorp.com/.../commercial.../undercounters...

Hobart CorporationGlasswasher ... The Hobart LXe Undercounter Dishwasher is designed to pack best-in-class cleaning power into a compact space, ... The Advansys LXe low-temp model features PuriRinse, a cold-water rinse that removes chemical residue, ...

[PDF]AM15 Technical Manual - Hobart

https://my.hobartcorp.com/kroger/.../AM15%20Technical%20Manual.pd...
Steam Booster, if used based on 20 PSI steam - 20 PSI water flowing. 130°F entering.... DRAIN AND OVERFLOW: Large bell type automatic overflow and drain ...

[PDF]Glass- and dishwashers - Hobart



Dec 08, 2015 | Hobart Undercounter Glasswasher w/Chemical...

1 Answer

Hobart lx30h rinse additive is running all the


The main cause is the "anti flood" device at the bottom of the washer that detects a water leak "hose leak" etc. This device made up of a polystireen float and micro switch is a safety device and when activated puts the washer in pump out mode only. You need to look at the base of the washer and see if water leak has caused this. Rectify the cause "normaly hose or clamp" and this should clear the

Mar 21, 2010 | Hobart 29 in. AM15-1 Free-Standing...

1 Answer

Hobart AM15T ML-130039 with p2 message, what does this code mean


p2 would mean your rinse thermistor is open or shorted. its located on top near the the right side, after the vac. brkr. part# is 328994. remove old, istall new . dont forget to vote,hope this helps , monomoy

Jan 29, 2010 | Hobart 29 in. AM15-1 Free-Standing...

2 Answers

No rinse cycle


If it is new, would you not call Hobart for a warranty call? 1-800-444-4764 to reach the nearest branch in Canada.
Seeing it's new it is most probably not programmed correctly. On the control board is factory jumper J5, short thse two pins and press ON on keyboard. when the display shows ty remove short. pressing select on the CB will change the options, pressing up arrow will incriment the change options. first setting is machine type= AS,second is id, hot/cold or plain AM15 only, select H,C,or P.
3rd is tc,auto temp control. The rest will not affect your condition. Press OFF on keyboard to save and exit.

Jul 03, 2009 | Hobart 29 in. AM15-1 Free-Standing...

2 Answers

What is p3 code on hobart am15 dishwasher


It means that the final rinse thermistor is bad.Your not getting 180 degrees---right?Its located on the booster and costs about $65.I work for hobart.Any ?

Jan 08, 2009 | Hobart 29 in. AM15-1 Free-Standing...

6 Answers

Error code E2 (with a picture of a wrench)


E2 means a problem with the fill. The wrench means to contact Hobart for service

Feb 27, 2008 | Hobart 29 in. AM15-1 Free-Standing...

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hobart Dishwashers Experts

GPEC

Level 1 Expert

12 Answers

Jason

Level 2 Expert

218 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Are you a Hobart Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...