Question about Invicta Watches

Open Question

How do I know what model Invicta men's watch I have?

Posted by on

Ad

5 Suggested Answers

escapement

Arturs Kalnins

  • 2338 Answers

SOURCE: Invicta 2875 wrist watch band too large

You may or may not have arrows inside bracelet.Arrows are pointing the way the pins must come out.
First you have to find out what sort of pins or even screws are used to keep links together.
Examine both bracelet sides and find the side where pin ends have a groove.
Start with a tiny screwdriver and unscrew one of the screws. If it turns, but doesn't come out, that means you have a pins instead.
For removing pins the best would be pin removing tool (approx.5GBP on ebay), but it's possible to do the job without it.
Take a hardened steel needle and blunt the sharp end to the approx. size of pin end diameter using any sharpening stone or sandpaper. Get an old towel and fold it to make a soft base for work (like small cusion). As you don't have a special bracelet holder you will need a pair of helping hands to hold the bracelet steady upright. You will need small hammer and pair of flat nose pliers as well.
NOTE: The pins MUST be driven split end out first, not vice versa. Make sure that the grooved pin ends are facing towel, not the needle and hammer!!!
Now place the watch on the folded towel, take that needle and smallest hammer you have and start driving the pin out using light blows. Do Not hit hard, as you will brake the needle, scratch your watch or even injure yourself. Watchmakers are using 45 gram hammer, so, calculate your strength of blows.
After a few blows check if the split end is coming out and when you see that the end is long enough to grab it with pliers, pull the pin out with pliers. When pulling, do NOT turn pliers, as pins tend to brake when twisted. Use firm grip and your strength to pull the pin without twisting.
After shortening the bracelet or adding extra link(s) make sure that the pins go back EXACTLY the same way as they came out- the blunt end first in the hole and the split (grooved) end last. Before doing that check remaining pins in bracelet to make sure that you put them back from the right side of bracelet.
It is recommended to use plastic hammer to drive pins back in or you will scratch or damage bracelet. If plastic hammer is not available use an old toothbrush handle (or some plastic item) as an absorber. Simply put pin into the hole as deep as you can with your fingers, put the toothbrush handle on split pin end and hit handle, not the pin.
Make sure that pin ends are flush with bracelet. If needed- hit few more times.
Job done!
If you do not want to do it yourself, any jeweler will do it in a matter of few minutes.
Don't forget to rate, please.

Posted on Mar 01, 2009

Ad
escapement

Arturs Kalnins

  • 2338 Answers

SOURCE: need to resize watch braclet on a mens invicta watch

You may or may not have arrows inside bracelet. Arrows are pointing the way the pins must come out.
First you have to find out what sort of pins or even screws are used to keep links together.
Examine both bracelet sides and find the side where pin ends have a groove.
Start with a tiny screwdriver and unscrew one of the screws. If it turns, but doesn't come out, that means you have a pins instead.
For removing pins the best would be pin removing tool (approx.5GBP on ebay), but it's possible to do the job without it.
Take a hardened steel needle and blunt the sharp end to the approx. size of pin end diameter using any sharpening stone or sandpaper. Get an old towel and fold it to make a soft base for work (like small cusion). As you don't have a special bracelet holder you will need a pair of helping hands to hold the bracelet steady upright. You will need small hammer and pair of flat nose pliers as well.
NOTE: The pins MUST be driven split end out first, not vice versa. Make sure that the grooved pin ends are facing towel, not the needle and hammer!!!
Now place the watch on the folded towel, take that needle and smallest hammer you have and start driving the pin out using light blows. Do Not hit hard, as you will brake the needle, scratch your watch or even injure yourself. Watchmakers are using 45 gram hammer, so, calculate your strength of blows.
After a few blows check if the split end is coming out and when you see that the end is long enough to grab it with pliers, pull the pin out with pliers. When pulling, do NOT turn pliers, as pins tend to brake when twisted. Use firm grip and your strength to pull the pin without twisting.
After shortening the bracelet or adding extra link(s) make sure that the pins go back EXACTLY the same way as they came out- the blunt end first in the hole and the split (grooved) end last. Before doing that check remaining pins in bracelet to make sure that you put them back from the right side of bracelet.
It is recommended to use plastic hammer to drive pins back in or you will scratch or damage bracelet. If plastic hammer is not available use an old toothbrush handle (or some plastic item) as an absorber. Simply put pin into the hole as deep as you can with your fingers, put the toothbrush handle on split pin end and hit handle, not the pin. 
Make sure that pin ends are flush with bracelet. If needed- hit few more times.
Job done!
If you do not want to do it yourself, any jeweler will do it in a matter of few minutes.
Don't forget to rate, please. 

Posted on Apr 02, 2009

Ad

Michael Chaffin

  • 183 Answers

SOURCE: how do i set the time on an Invicta Lupah mens

The Lupah has a chronograph so dont worry about the sub dials while your setting the time. Pull the crown out to the first position and set the time. For the date pull out to the second position and set the date.

To set the chronograph sweep arm pull the crown out and press and hold down the start button. The sweep arm will move into position. Stop it on the 12:00 or 0 position.

Posted on Sep 18, 2009

Anonymous

  • 110 Answers

SOURCE: What kind of battery does the Invicta Men's

The correct answer is to examine the battery that is in it and identifying the markings on the old battery. To do this you will need of course to remove the case back. Now if the watch does not have a battery in it then that is another story. Sometimes you will see the battery type marked on the inside cover of the case back. Hope that helps, Best of Luck

Posted on Nov 19, 2009

Anonymous

  • 9 Answers

SOURCE: how do i set the gmt on my Invicta Men's Pro Diver

Set it only at night but not between 8 and 2. Use the johnson rod that came with it.

Posted on Jan 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I want a link for invicta pro diver model 0886


https://www.invictawatch.com/watches/detail/0886-invicta-pro-diver-men-488mm-stainless-steel-stainless-steel-silver-dial-pc32a-quartz

Nov 11, 2016 | Invicta Watches

1 Answer

I would like to know how to remove the back and change the battery.


There appear to be several models in Invicta Signature Watches.
Your best bet is youtube. one is shown below Battery Change Invicta Men 2770 Force Collection super easy

Apr 02, 2016 | Invicta Signature Watches

1 Answer

Invicta model 12983, how to set day on the subdial


View the instruction manuals - Invicta

invictawatch.com/service/view-the-instruction-manuals
Enter your 4 or 5 digit model number to locate your watch. RECEIVE THE NEWSLETTER SOCIAL MEDIA · Terms & Conditions Customer Service Service ...Missing: 12983 ‎subdial

Setting Time Date Invicta Watch Chronograph - SmartBargains

https://www.smartbargains.com/.../Setting-Invicta-Chronograph.html
Know how to set time, day, and date in the Invicta Watch Chronograph. ... Invicta sells several different kinds of chronograph watches, with the two main ... and the Invicta Big Date and Day chronograph - the subdials that measure seconds and ...Missing: 12983

Invicta Reserve 48mm Octane Swiss Made Quartz ...


Jan 16, 2016 | Invicta Reserve Mens Arsenal Swiss Quartz...

1 Answer

Need a replacement band for Invicta Mens 4578


with the model number you should be able to find one easily on ebay or amazon. ask the seller any questions before purchase if unsure.

Mar 24, 2014 | Invicta Mens 4578 Russian Diver Collection...

1 Answer

Invicta 8926A gains about 2 or 3 minutes after winding.


Send in for warranty repair with a description to Invicta

Oct 12, 2012 | Invicta Automatic Pro Diver 8926A Wrist...

2 Answers

Hello, I hope that you can tell me some true info about this watch. It is the Invicta Subaqua Noma III (above). Watch descriptions say that the watch has a unidirectional rotating bezel. Is this true??...


<P>Thank you for contacting FixYa.</P><P>I dont know much about Invicta, however they have a wonderful website where you can download instructions or contact them.</P><P><A href="http://www.invictawatch.com/welcome/manuals/">http://www.invictawatch.com/welcome/manuals/</A></P><P>Best regards.</P>

Aug 27, 2010 | Invicta Subaqua Noma Iii Chronograph men...

1 Answer

I own an Invicta Russan Diver Model #4578 and I nee replacement screws for the rubber strap. Do you know where I can find them ?


mcdevito75 here, I would contact shop NBC for info, here is their contact number, 800-474-6762 They should guide you to Invicta parts.

Aug 13, 2010 | Invicta Russian Diver Quinotaur Ccp...

Not finding what you are looking for?
Watches Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Invicta Watches Experts

Janelle Schoonover
Janelle Schoonover

Level 3 Expert

842 Answers

Kardoc

Level 3 Expert

5488 Answers

Tom Lambert

Level 1 Expert

10 Answers

Are you an Invicta Watch Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...