Question about Hardware & Accessories

Open Question

How to set run time on a pope dy997 tap timer

Posted by on


3 Suggested Answers


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017



  • 1 Answer

SOURCE: how to set up a pope easy set automatic tap timer

How to set up Pope auto matic sprinkler system timer. Lost my directions. Need for 6 outlets on odd days

Posted on Feb 15, 2011


Steve Papp

  • 1010 Answers

SOURCE: My pope easy set tap timer has locked after flat batteries now won't turn on

Do you have a reset button?

Posted on Mar 24, 2013

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My gardena water timer won't stop bipping. See the picture. Is it the battery ?

for the Gardena-T-1030-1805 model....
Gardena 1030 1805 Operating Instructions Manual Page 7

11. Battery
11.1 Status indicator
If the battery capacity falls below a certain level, a warning signal sounds every 15 seconds. The programs you have set are not run. The water flow cannot be opened manually. If a valve is open, however, it will be closed.
11.2 Changing the battery
If the battery capacity is too low (the warning signal beeps every 15 seconds), you must change the battery.

To do this, the water timer must be removed from the tap.
Important : Changing the battery deletes the data you have set.
To change the battery :
1. Insert the battery in the battery compartment
2. Set the Run Time control knob
3. Reset the watering data as described in "Setting the watering data".
3 If the Run Time knob is not turned to Reset, 5 seconds after the
battery was inserted the current Run Time shall be accepted. This is confirmed by a double beep.

Note : The time the battery was changed is taken to be the starting time.

To ensure that the water timer works properly we recommend that you insert a new battery at the beginning of every gardening season, or at the latest after a year.
Important ! Please dispose of used batteries properly at the appropriate communal waste disposal site. Only dispose of batteries when flat.

May 28, 2016 | GARDENA Hardware & Accessories

1 Answer

Poping sounds from top of engine while running

Without hearing the noise, popping back thru the intake often indicates incorrect spark timing or badly worn timing components. Double clack is piston pins, single tap may be valves out of adjustment, sticking, tappet noise, etc. Use a section of hose with one end in your ear to listen all over engine to find location of noise. CAUTION--beware of spinning fan blades.

Oct 08, 2015 | Cars & Trucks

1 Answer

Why can I not get past the "set time" on Gardena water timer?

Check if you get water from the tap without water timer.
Look for obstruction in filter washer (rubber washer with screen mesh to keep debris out of timer)
Battery operated water timers are made to last few years, and cannot be exposed to freezing temperatures or hot sunlight


If you need further help, I’m available over the phone at

Jul 29, 2014 | GARDENA Water Timer

1 Answer

How to operate pope tap timer (N1625)

Call Pope 1300 134 880
Pope user guides does not show N1625

If you need further help, I’m available over the phone at

Feb 03, 2013 | Hardware & Accessories

7 Answers

Pope digital set automatic tap timer screen shows "err"

These timers seem to be very robust and one has been operating for several years without any problems. After a period of rain I turned the tap off to prevent the timer turning the water on. The "err " message was there when I next went to turn the tap on. Judging by the intstructions there is an internal battery of some kind which flashes a "OP" message. I took out the main batteries and the "OP" signal started to flash, I then removed the four screws from the back of the timer but could see no obvious way of resetting it. I took a guess which luckily turned out to be correct and briefly bridged two contacts on top of the timer (see picture). The screen went blank and when I re-installed the batteries it had re-set itself to. All buttons are also working.
I imagine that there have been many of these thrown out with the garbage un-necessarily when the solution is quite a simple one. Pope would be doing a service to the planet by fitting these timers with a reset.

Feb 01, 2013 | Washing Machines

1 Answer

When pool pump stops at various times when it should be running and not everyday, but sometimes twice a day, if I tap the Tork timer dial it turns on. Only the timer dial, tapping anything else does not...

Could be loose wiring, or bad clock motor.
Check if wires are connected, and make sure only the copper part of wire and no insulation is under the screw plate.
Make sure all wires are same gauge so that screw plate clamps down on wires.
Open following link to identify timer and then add a comment with model number and voltage for possible help. Tork T1100 series has replacement clock motor.

Jun 29, 2011 | York Hardware & Accessories

1 Answer

How to set up a pope easy set automatic tap timer

How to set up Pope auto matic sprinkler system timer. Lost my directions. Need for 6 outlets on odd days

Oct 05, 2009 | Garden

Not finding what you are looking for?
Hardware & Accessories Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hardware & Accessories Experts

Gene Haynes

Level 3 Expert

5390 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Brad Brown

Level 3 Expert

18110 Answers

Are you a Hardware and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides