Question about Behringer Music

Open Question

FX channels on Behringer PMP 1680S not working--only producing a rapid, repetitive clicking noise

Posted by on

Ad

3 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
hmerchant110

AliTech110

  • 7191 Answers

SOURCE: I need an owner manualfor a Behringer pmp 3000 16 channel mixer

Hi,

You can download the manual by clicking this link

You'll require Adobe PDF Reader installed on your PC to view this manual. If it is not already installed on your PC, download it free from:

http://get.adobe.com/reader/

Hope this solves your problem. Thanks for using FixYa

Posted on Jan 15, 2010

Ad

Fred Yearian

  • 5603 Answers

SOURCE: I have Behringer PMP 3000 2 channels not working

Fan speed depends on temp sensors. If doesn't run at all when unit is loaded, take in for repair immediately.

If FX window changes with the control, chances are you have not set the controls properly. You need to havew THREE places turned up for effects: The FX knob in the desired channel(s), The FX slider and finally the knob to send the FX to the mains and/or monitors.

OFTEN the stereo channels aopear to not be working because of the A/B switch between the RCA and 1/4 inch jacks.

You did not give me enough info regarding which channels appear to not work.

Posted on Sep 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Monitors not audible with Behringer 1680S


Assuming you're trying to power the monitors from this unit as well as the mains.....Confirm that the amp switch is in the middle position which splits the internal amps....one for main and one for monitors. Output A would power the monitors.... B would power the mains.

Aug 26, 2012 | Behringer PMP1680S Europower 10-Channel...

1 Answer

I have a behringer eurorack ub1204fx hooked up to a bose L1. I can't seem to get the reverb to work


you have to set three gain controls to pass the FX into the mix. The FX send gain for each input channel, the FX fader which sends the FX mix to the effects unit, and finaly the gain that sends the FX output to the mix. Depending on which effect you choose, some are very subtle.

Aug 06, 2011 | Behringer Pmp3000 16 Channel Audio Mixer

2 Answers

When i have my FX on and sending to main they make a horrible clicking (shorting out) sound. if I push the main mix button it shuts off the effects and the noise goes away...bad side...then I have no...


Check the 5 volts to the FX unit, If the voltage is low, the FX processor will keep reseting generating clicks, In a different product, the 5 volt filter cap was degraded and voltage dipped down to 4.5 volts causing resets.

May 31, 2011 | Behringer EURORACK UB2442FX PRO Mixer

1 Answer

I have a pmp 3000 and a pmp 6000. what is the best wast to run out of the boards to the speakers? and is it better to run in mono?


No preference, just use mode that fits your venue. As far as system safety I would run in Stereo A/B rather than bridged mode.

Now please read my tip about PMP units on Fixya regarding a hazard if you convert the Speakon outputs at some point to 1/4 inch plugs. If you do this, please note that the SLEEVE, not the tip on channel A is HOT to ground and shorting this to ground will often fry channel A. Channel "B" the tip is the hot speaker lead. Thsi is done by Behringer to facilitate switching to bridged mode.

Mar 06, 2011 | Behringer Pmp3000 16 Channel Audio Mixer

1 Answer

I have a behringer PMP 3000 mixer, on e of the channel is gone, it is not under warranty, can you tell me who can repair it ? what causes the channel to blow.


Often the A channel power output blows. CEASE using the unit immediately until repaired as continued use can have additional damage to power supply.

Any problem with speakers can blow the channel as there is real weak insulation on a multi-layer circuit board in the rear most amp (channel A). It burns and takes out three transistors on the HCA2400 module inside.

ALSO read my tip on here regarding a hazard of Behringer PMP units due to the channel A connection when using Speakon to 1/4 inch plugs or adapters having the BARREL being the hot lead instead of the TIP of the 1/4 inch plug. Short that barrel to ANY ground and goodbye channel A.

Jan 06, 2011 | Behringer Pmp3000 16 Channel Audio Mixer

1 Answer

I have Berhinger 1680s powered mixer I have 2 Mackie 350 V powered speakers Can I hook them up? How do I?


Thought I answered this. Using balanced TRS cables, connect the powered speakers to the Main L and R 1/4 inch jacks on the top of the unit.

Nov 27, 2010 | Behringer Pmp3000 16 Channel Audio Mixer

1 Answer

I have Behringer PMP 3000 2 channels not working fx not working and fan not working but unit turns on ok


Fan speed depends on temp sensors. If doesn't run at all when unit is loaded, take in for repair immediately.

If FX window changes with the control, chances are you have not set the controls properly. You need to havew THREE places turned up for effects: The FX knob in the desired channel(s), The FX slider and finally the knob to send the FX to the mains and/or monitors.

OFTEN the stereo channels aopear to not be working because of the A/B switch between the RCA and 1/4 inch jacks.

You did not give me enough info regarding which channels appear to not work.

Sep 26, 2010 | Behringer Pmp3000 16 Channel Audio Mixer

2 Answers

I need an owner manualfor a Behringer pmp 3000 16 channel mixer


Hi,

You can download the manual by clicking this link

You'll require Adobe PDF Reader installed on your PC to view this manual. If it is not already installed on your PC, download it free from:

http://get.adobe.com/reader/

Hope this solves your problem. Thanks for using FixYa

Jan 15, 2010 | Behringer Pmp3000 16 Channel Audio Mixer

Not finding what you are looking for?
Music Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Behringer Music Experts

Michial Gueffroy

Level 3 Expert

1140 Answers

Chickenwatt

Level 1 Expert

18 Answers

Ric Weide
Ric Weide

Level 1 Expert

10 Answers

Are you a Behringer Music Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...