Question about Home Security

1 Answer

I can not open my digital safe. password do not work, and no sound when I am pressing digital buttons

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Home Security Master
  • 22,486 Answers

Battery dead --notify manufacture or locksmith

Posted on Jun 01, 2019

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
pgh_pa_guy

  • 2992 Answers

SOURCE: My Craftsman 53684 keyless won't work with my Craftsman 53930DM.

I've never seen the first set of steps you mention. You always need to press the "learn" button first so the opener will be in the mode to capture the new code. As far as I know it is not necessary to hold the Enter button on the keypad (at least I never have). While the "learn" LED is lit on the opener, just key in the new code and press Enter.

Maybe you should try clearing the receiver first by pressing the "learn" button and holding it until the LED either goes out or starts flashing (depends on model). Then try reprogramming. Maybe the little computer is confused.

Posted on Dec 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mother just past away,luckily safe was open at time,but dont know combo to keypad or we haven't found a key,how do i reset code to sentry10 gunsafe


To reset the combination on a Sentry safe, open the door of the safe, delete the existing codes, press the PROG or P key and enter the factory code. Finally, enter a new five-digit number as per individual preference, which is the new user combination.
It is always prudent to reset the combination on a Sentry safe when the door is open because it prevents the user from being locked out. To open the Sentry safe door, type the five-digit factory code given in the owner's manual. This factory code cannot be altered.
To delete the existing codes on newer models of the safe as of 2015, press the P button. Then, type the factory code and follow it up by inputting "00000" into the safe. On older models of the Sentry safe, press the PROG button and type the factory code two times.
After deleting the existing codes, press the PROG or P key and then enter the factory code once again. Within five seconds, type a new five-digit number, which is the new user code. To verify if the user code is working, retype it and then close the door of the safe. The user code is the primary code for opening the safe, and users can reset it as often as they want too

Mar 21, 2017 | We Home Security

1 Answer

How do i get the combo for sentry safe


Either sit it on a cushion and thump it with your hand, then quickly turn the open knob (takes practise) or drop it an inch or two onto a hard surface and quickly turn the opening knob.
This will release the locking solendoid for a 1/2 second allowing you to open it if you're quick.
You can then set a new password byu pressing the button inside.
The default password is usually 159 so try that first.

Mar 01, 2015 | Sentry Fireproof Safe

1 Answer

How do i set code for paragon safe


INITIAL BATTERY INSTALLATION
1. Remove the key plate cover, insert the key into the keypad and open the door.
2. Remove the battery cover plate located on the inside of the door.
3. Install 4 AA batteries provided and replace the battery cover.
NOTE
: If both the red and green lights are on while the safe is open, this indicates that the batteries are low and need
to be changed.

TO SET UP OR CHANGE A USER CODE
1. With the door open, locate the red button on the back of the door near the hinge.
2. Press the red button and listen for the beep.
3. Immediately enter your new passcode (3-6 digits long)
4. Immediately after entering your new passcode, press the "A" or "B" button on the keypad. Your new user passcode is now stored.
NOTE:
This safe stores up to 2 passcodes (a user code and a manager code). Entering a third code will erase the
first passcode entered.

SETTING UP OR CHANGING A MANAGER PASSCODE
1. Open your safe with the passcode you wish to change and leave the door ajar.
2. Press the "0" button on the keypad twice. Press the red button, listen for a beep and then enter your new user passcode.
New user passcodes may be 3-6 digits long.
3. Immediately after entering your new code, press the "A" or "B" button on the keypad. Your user code is now changed.
OPENING THE SAFE
1. Input your code and then press the "B" button, the green light will turn on.
2. Turn the knob clockwise within 5 seconds to open the door.
3. Each key pressed will be accompanied by a buzzer and a yellow flashing light. If the entered code is invalid the yellow light will
flash and the buzzer will quickly sound, this indicates the code needs to be re-entered.

CAUTION
: Entering the incorrect passcode 3 times will lock the system for 20 seconds.


More information can be found in the attached document web page.

http://www.paragonlockandsafe.com/manuals/mastermanual.pdf

Aug 29, 2014 | Paragon Electronic Digital Safe Jewelry...

5 Answers

Cannot open my secret safe by justice


Reference: Paisley Electronic Push Code Safe
Item # 5661462
Purchased at Justice. May be one of the following design/colors: 1. Pink and black 2. neon green 3. tye-dye (all in zebra pattern, I believe)

To gain access to safe without code proceed with the following simple instructions:

Use a screw driver to access batteries on the bottom of the safe. Remove all three AA batteries.
WAIT AT LEAST TEN SECONDS before reinserting betteries to functional position. Replace screw. Key in default passcode "0000#" Safe will now be unlocked and upon opening you can reset passcode. Hold down the "*" and when voice prompted to "key in passcode" enter new 4 digit code followed by the # sign... HOLD "*" until completed code with "#" You will hear the voice command, "enter passcode" after each digit entered. [Press & hold "*" (1234) press "#" release "*"] Close safe and new passcode should be set and work properly. If not, enter default "0000#" and try to reset once again.

Feb 03, 2014 | Toys

1 Answer

I need to change the code on the safe and I no longer have a manual for my LS405 Sandelford Electronic Safe. It has a number N15115 on the front of the safe I cannot remember how to do this


This may work:

1. With the safe open press the red button on the hinge near the back of the door.
2. Release the red button 2 beeps will sound, followed by illumination of the yellow light.
3. Enter the predetermined 3 to 8 digit code.
4. Confirm the code by pressing the letter B.
If the code or confirmation is not complete in 15 seconds begin again at step one.

NB. Make sure the batteries are fresh.

May 30, 2011 | Office Equipment & Supplies

2 Answers

My son has a discovery kids safe....we lost passcode. Can it be reset? Numbers/letters on bottom of safe are: YLBSD-NI 2006 07 12330


The Discovery Kids Safe works slightly differently. When you press the reset button on the bottom of the safe, the code defaults to "1234". To set a new code, Press *, then your four-digit code, then * again.
Emergency Open: In case of malfunction, hold down "WIRE" button and push on the drawer.

Feb 15, 2011 | Discovery Kids Toys

1 Answer

Just put new batterys in safe . but safe will not stop bleeping what is the problem


Please follow these steps
Programming a user code
There are two ways to program a user code.
A 1. Press the Program key.
2. Enter the Factory Code. The green LED remains ON
while you enter the 5-digit user code of your choice.
After 5 digits are entered the green LED turns OFF.
(To enter a new User Code, repeat these steps.)
B 1. Press the red button inside the safe. The lock will
beep and the green LED will come on.
2. Enter a 5-digit user code.
(To enter a new User Code, repeat these steps.)
Keep your new user code secure.
For your records, please copy it here:
____ ____ ____ ____ ____
Programming a password
1. Press the Program key.
2. Press it a second time.
3. Enter your 5-digit User Code. The green LED remains ON.
4. Enter the 5-digit Password of your choice (any combination
except 00000.) After 5 digits are entered, the green LED
turns OFF.
(To enter a new Password, repeat these steps. To erase the
Password, press Program twice, enter your User Code and then
enter 00000.)

Battery replacement
Below When old batteries are removed for replacement, your Password will be voided; only Factory and User Codes will work. To
reestablish your Password, follow the directions above under
Programming a Password.
Key override
If your electronic lock fails or you do not have any codes
available, you may use a key override to access this unit.
1. Remove the battery cover, disconnect and remove the
battery holder.
2. Insert the skeleton key (second set of keys provided)
into the key hole inside the opening for the battery.
3. Turn the key to the right.
4. Turn the four bit key to the right.
5. Open the door.
Signals
Your electronic-lock safe communicates by means of several
audio/visual signals.
Red (Error) LED + three beeps indicates
one of the following:
1. You have pressed Program key out of sequence
2. You have entered an invalid code or password.
3. You have let 5 seconds or more elapse between key entries.
Green (Proceed) LED + single beep occurs
1. After entering each digit of Factory or User Code, or
Password
2. After pressing Clear key
3. After pressing Program key
Green LED only
1. Comes on after you enter a valid code/password and
remains lit during the 4-second period in which the safe
can be opened.
2. Comes ON in the Program User Code mode after you enter
the Factory Code and remains lit until you have finished
entering a 5-digit User Code.
3. Comes ON in the Program Password mode after you have
entered your User Code and remains ON until you have
entered a 5-digit password.
Yellow LED
Indicates low battery and will typically not turn ON until
battery has been in use approximately two years or longer.
Your electronic lock automatically performs a low battery test
during each lock use.
If a �low battery� condition is detected the Yellow LED will
come ON and remain ON during each subsequent lock
operation. (The lock will continue to function in a Low Battery
state, until battery failure.) The Yellow LED will turn OFF only
after three consecutive Good Battery readings or after the low
batteries are replaced. (Note: If the new batteries are installed
in less than 60 seconds the Yellow LED may come ON and stay
ON during the first lock operation before it returns to OFF.)
NOTE: It is recommended you replace the batteries after two
years, or when the yellow LED remains on.

Jan 09, 2011 | Safe International Electronic Digital Safe...

1 Answer

How do i reset an averatec 3200


try to open your your system in safe mode from there you can change your password.
for opening in safe mode press F8 when BIOS screen appears and select open in safe mode.

Apr 22, 2009 | Averatec 3200 Notebook

10 Answers

Forgot pin code to unlock my hardline digital safe


I have pin code but batteries went flat while I was on holiday, how do I unlock my Hardline digital safe? I do not have override key

Dec 09, 2008 | Safe International Digital Electronic Safe...

10 Answers

Nutool SF10 electronic digital safe


Open the safe door and press the s key press the I key twice then press the red button on the inside of door near the hinges. you will hear 2 long beeps. press the s key and then the red button and you will hear a beep enter your combination up to 12 numbers then press the E key your combination is now set. Best of luck

Sep 05, 2008 | Computers & Internet

Not finding what you are looking for?
Home Security Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Home Security Experts

Brad Brown

Level 3 Expert

18157 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Lawrence Oravetz

Level 3 Expert

10543 Answers

Are you a Home Security Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...