Question about Hitachi Heating & Cooling

Open Question

My Hitachi air-condition timer light blinking 4 times

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 68 Answers

SOURCE: air conditioning light blinks, turns off

either the belt is loose or there is a compressor issue (either the clutch or the compressor is most likely shot)

I used these guys for my last one to have it shipped to me. If you haven't done this before it is not an easy DIY job (you need a vaccum pump, and gauges to do it correctly

http://www.discountacparts.com/

Posted on Feb 05, 2009

Ad

Anonymous

  • 218 Answers

SOURCE: AIR BAG LIGHT BLINKING

THAT IS A CODE 44 RIGHT FRONT PRIMARY AIR BAG SENSOR TO PRPERLY MOUNTED TO VEHICLE

Posted on May 01, 2009

rulds2008

Grand Canyon Tech

  • 3866 Answers

SOURCE: tv turns on then off, stand by timer light blinks 4 times

You need to replace the power supply unit on this as it has malfuctioned there about $90 bucks plus labor on that.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edwy_1a56970cf1ea4620

Posted on May 25, 2009

xxxxxx xxx

  • 5013 Answers

SOURCE: Air bag light blinks 4 times then pauses then 4

Common fault on FORD
Usually due to a poor connection in the YELLOW PLASTIC CONNECTOR underneath the passenger seat.


Just push it together properly and it should clear the AirBag fault


Posted on Sep 06, 2009

Anonymous

  • 288 Answers

SOURCE: HI, I have a Fujitsu ASTA18lCC. Fan working but

trying to get the compressor to operate. it could be a bad capacitor and the compressore wont start or maybe the compressor is burned up

Posted on Dec 15, 2009

Testimonial: "Thanks for the advice. It turned out that we had a blackout after the AC had started playing up. The blackout seems to have sorted out the problem.Thx"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

3 time timer light blinking in ogeneral Inverter split


You have to try resetting the system. First turn the breaker off for the condenser and wait about 20 seconds. After you turn it back on the system should reset.If you need any other air conditioning help check out Air Conditioning Repair Tamarac we will be sure to answer any question you have.

Jul 09, 2016 | Inverter Heating & Cooling

1 Answer

Mitsubishi timer light 6 times blinking


Indoor unit indicator
RUN lamp = 6 time flash
TIMER lamp = Comes on
Outdoor unit indicator (LED5) = Stays off
Description of trouble = Indoor fan motor error (2)
Cause = Defective fan motor, Connector poor connection
Conditions of flashing = When air conditioner is operating and indoor fan motor is turned ON, indoor fan motor speed of 400 rpm or under continued for more than 30 seconds. (Air conditioner stops.)

May 29, 2016 | Mitsubishi Heating & Cooling

1 Answer

When i turn on my tv it tries to boot, blue mitsubishi home screen come up, i hear fan then it all shuts off while green light blinks.


Try a reset. Start by unplugging for 1 minute, then plug back in & if still won't restart try the following. If none of the following work, you will need a technician.

Initializing the TV in many cases can remedy a problem.
In the 2006 product line Initialization is now a user function.
Pressing the front panel "INPUT' and "FORMAT"
buttons at the same time activates Initialization. When
complete all user settings will have to be set again. The
table in Figure 4-3 list the User Initialization procedures.
Note: Pressing INPUT and FORMAT is the same as
the Initialization in the Option Menu (MENU-2-4-7-0)
Order Name Procedure Results Notes
1 System Reset Press <System Reset>
on Front Panel
Hardware & TV operating
software reset.
POWER/Timer LED flashes for 60
seconds. No customer settings
are changed.
2 User Initialization
Press <INPUT> &
<FORMAT> on Front
Panel at the same time.
All customer Audio &
Video settings are reset to
factory default.
All customer settings will need to
re-configured.
3 Reset System
Defaults
From the remote, press
<MENU> <1-2-3>
<ENTER>
All customer settings
except V-Chip are reset to
factory default.
Netcommand, Channel Memory,
etc., will need to be re-configured.
SERVICER
PROCEDURE 4 Initialization
From the remote, press
<MENU> <2-4-7-0>*
select "INITIAL" press
<ENTER>
All customer settings are
reset to factory default.
All customer settings will need to
re-configured.
MITSUBISHI RESET / INITIALIZATION CHART
CUSTOMER
PROCEDURES
Figure 4-3
Figure 4-4
LED Indications
The front panel LEDs, refer to Figure 4-4, also assist in
determining the cause of a symptom. Figure 4-5 illustrates
normal LED operation. Figure 4-6 shows the
LEDs response when a problem is detected and indicates
the possible cause.
Power/Timer
Indicator
Status
Indicator
Lamp
Indicator Condition
Off Off Off Off (standby)
Blinking green
fast Off Off Initialization (10 - 65 seconds)
Off Off Blinking
green fast Lamp runs for 1 min after PTV off
Green Off Off Power On
Blinking green Off Off Power On Timer is set
NORMAL LED INDICATIONS
Power LED Status LED Lamp LED Condition
High Temperature - check ventilation air flow.
(Temperature sensor is disconnected.)
Off Off Blinking yellow Lamp cover is open.
Lamp failure (Lamp fails to turn on)
Off Off Red (Lamp turns off after lighting)
Lamp is broken
Off Blinking Red Off Fan Stop
Off Red. Off Circuit failure. (Run Error Code Check)

Apr 08, 2015 | Mitsubishi WD-65731 65-Inch 1080p DLP HDTV

1 Answer

Panasonic air con - when you turn the air con on it runs for about 3 mins and then the timer light flashes. Air con will not work.


• Once abnormality has occurred during operation, the unit
will stop its operation, and Timer LEDs blink.
• Although Timer LED goes off when power supply is turned
off, if the unit is operated under a breakdown condition, the
LED will light up again.
• In operation after breakdown repair, the Timer LED will no
more blink. The last error code (abnormality) will be stored in
IC memory.
• To make a diagnosis:
1. Timer LED start to blink and the unit automatically
stops the operation.
2. Press the CHECK button on the remote controller
continuously for 5 seconds.
3. "- -" will be displayed on the remote controller display.
Note: Display only for "- -". (No transmitting signal, no
receiving sound and no Power LED blinking.)
4. Press the "TIMER" or button on the remote
controller. The code "H00" (no abnormality) will be
displayed and signal will be transmitted to the main
unit.
5. Every press of the button (up or down) will increase
abnormality numbers and transmit abnormality code
signal to the main unit.
6. When the latest abnormality code on the main unit
and code transmitted from the remote controller are
matched, power LED will light up for 30 seconds and
a beep sound (continuously for 4 seconds) will be
heard. If no codes are matched, power LED will light
up for 0.5 seconds and no sound will be heard.
7. The breakdown diagnosis mode will be canceled by
pressing the CHECK button continuously for 5 sec-
onds or without any operation the remote control for
30 seconds.
8. The LED will be off if the unit is turned off or the
RESET button on the main unit is pressed.

When you have the error code, we can work out what to do next.

Mar 27, 2015 | Panasonic Heating & Cooling

1 Answer

LG aircon flashes blinking 8 times and the shifts to timer led flashes blinking light 4 times


What is the make / model of your air conditioner. With out that information i cant help you with your ac repair problem.Air Bulance AC Cleaning Repair Services

Apr 23, 2014 | LG Heating & Cooling

1 Answer

LG aircon operation flashes blinking light 8 times and then shifts to timer light flashes blinking light 4 times


Sounds like a 48 code. (There is no 84 to my knowledge).
Outdoor unit coil outlet (liquid line) thermistor has disconnected or has shorted out.

call a LICENSED hvac repairman

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/chris_e1fb7ef6a5bdb086

Apr 21, 2014 | LG LS-L1210CL Mini Split Air Conditioner

3 Answers

Air conditioner stopped working


Check the breaker in the panel and the fuses in the disconnect at the outside unit. If that doesn't do it. call a heating and air technician instead of an electrician.

Mar 01, 2009 | Hitachi RAS-09UH Air Conditioner

3 Answers

Fujitsu Heat Pump - problems with timer? When starting the heat pump - the operation light, together with the timer light blinks twice, then the operation light blinks another five times. Then the...


I had the same problem. The heater did not work in heating mode. However it was OK in air-conditioning mode. The operation light and the timer light blink twice and then the operation light blinks for 5 times followed by few seconds non blinking, then the cycle repeats again. I have read on the internet that you better unplug the power cord and then plug it again so that the heater re-sets itself. My only problem was that my heater is directly plugged to the power with no visible plug. So I went to the main distribution board and put off the power for about 20 seconds for the whole home. HOORAY!! The heater worked after that.

Jun 24, 2008 | Fujitsu Heating & Cooling

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hitachi Heating & Cooling Experts

Lawrence Oravetz

Level 3 Expert

10543 Answers

jws1013

Level 3 Expert

1660 Answers

bobalix

Level 3 Expert

471 Answers

Are you a Hitachi Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...