Question about GE Ovens

Open Question

F2 code and beeping on GE wall oven model JKP13G0P4BG.

Posted by on

Ad

5 Suggested Answers

Powerman

Charlie Popeck

  • 68 Answers

SOURCE: F2 Error code displays with audible beep.

The F2 typically means an overtemperature conditions:
1. over 650 degrees F unlatched or 915 degrees F latched.
2. cooling fan stalled while over above 650 degrees F or an oper thermal switch in the yellow leads.
Check for:
1.Welded relay contacts
2.Cooling fan stalled or blocked air flow to rear of unit.
3.High resitance in over sensor leads/connectors, especially at sensor in rear.

Posted on Nov 04, 2007

Ad

Anonymous

  • 146 Answers

SOURCE: F2 code and consistent beeping with my Maytag Electric Wall Oven model CWE5800 or CWE4800

The F2 code indicates a stuck relay. You will have to replace the relay board. It may be a stand alone board or it may be part of the ERC Electronic Range Control. If you know how to check you won't have to call a tech.

Posted on Dec 21, 2007

Ad

Anonymous

  • 1 Answer

SOURCE: GE self cleaning radiant oven - model JB578GP

I went out to my circuit breakers and turned the circuit off, let the oven cool, and powered it back up after about 2 hours. Fine now.

Posted on May 25, 2008

vitg55

Vitaliy Gins

  • 78 Answers

SOURCE: dacor single oven flashes an F2 error code and won't stop beeping!!!

This is from manufacture service manual:

-F2- Alarm Heating Mode High Temperature
Is activated when the ERC senses a runaway heat condition or when the temperature exceeds
“runaway limits”. The ERC will beep until the cancel or another function is selected. If the alarm
repeats the F2 alarm check the oven sensor and wiring after fi rst checking for a stuck relay. If alarm
goes away verify the oven will complete a clean cycle without any type of failure.
Another words the problem with oven sensor or relay board.

I’m happy to help further over the phone at https://www.6ya.com/expert/vitaliy_f406165329c75ede

Posted on Dec 18, 2008

jyackle5

Jyackle5

  • 8197 Answers

SOURCE: RBD305 Whirlpool wall Oven Beeped

You have a shorted control pad you need to replace it.

Posted on Jan 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

CONVECTION OVEN CONTINUES TO GIVE fault code and doesn't heat


you either have a bad sensor or a bad clock assy. change the sensor first or check it with a meter it should read around 1080 ohms if this is good you have a bad computer board or clock assy. same part.if this a slide in stove with the burners on top there should be a tech sheet on the back,if this is a wall oven there should be a tech sheet below the top panel,slide it out and tilt it forwards enough to remove the top panel and of course kill the power to it first

Nov 03, 2017 | GE Ovens

1 Answer

GE wall oven was in self clean mode and suddenly an F2 error keeps beeping. It also flashes looked door - please help


Those are error codes which are listed in your owners manual. If you do not have the manual go to the GE web site, customer support section.

Mar 06, 2011 | GE Ovens

1 Answer

I'm getting a F2 Error and door locked with flashing and beeping after I ran the self-cleaning mode on my GE Model JTP85 built-in oven.


f 2 code states that your oven temp exceeds 590 w/unlocked door .. the oven tempt sensor will need to be replaced .. hope this helped mm

Dec 04, 2009 | GE JTP85 Electric Double Oven

1 Answer

Error code f2


This usually means the oven detected an over-temperature condition (although F2 meaning varies by model). This can be caused by a faulty temperature sensor or a failed control board. Many of the control boards for the older models have been discontinued. We repair these at www.fixyourboard.com.

Oct 05, 2009 | GE Ovens

1 Answer

Error code F2 keeps beeping! Will not reset. Any


thats the oven sensor , replace the sensor and your good to go

Jun 17, 2009 | GE JKP27 Electric Double Oven

1 Answer

F2 and F3 error codes in GE electric wall oven


Call GE answer center 1-800-626-2000 ask for tech help, Have you Model # off you data plate ready.

May 09, 2009 | GE JRP15 Electric Single Oven

1 Answer

F2 code on GE selfcleaning oven


The F2 fault code generally means the Oven temp exceeds 590 w/ unlocked door High resistance or interference in oven temperature sensor Might want to check the oven sensor for high resistance. Get a ohm reading of the oven sensor at room temperature and tell me what this reading is.

Waiting to hear from you,
Eric Campion

Feb 14, 2009 | GE Ovens

1 Answer

F2 and F3 code appearing along with annoying beeping


i think f3 error code has something to do with the temp probe maybe it is the problem. the temp probe is located if you open the door directly in the back wall. it looks like a prong. should read 1100ohms the f2 error code though usually has something to do with the keypad i would check all the connections maybe they are loose.

Jan 04, 2009 | Kenmore 40494 / 40495 / 40499 Electric...

1 Answer

F2 error code


Intermittents are a real problem. My first guess: look around for a corroded or damaged electrical feed. Could be electrical noise from that. Not sure what No other possiblities other than a bad panel. I don't know what F2 is.

Dec 06, 2007 | GE JGRS14 Gas Single Oven

1 Answer

F2 Error code displays with audible beep.


The F2 typically means an overtemperature conditions:
1. over 650 degrees F unlatched or 915 degrees F latched.
2. cooling fan stalled while over above 650 degrees F or an oper thermal switch in the yellow leads.
Check for:
1.Welded relay contacts
2.Cooling fan stalled or blocked air flow to rear of unit.
3.High resitance in over sensor leads/connectors, especially at sensor in rear.

Nov 03, 2007 | GE JTP20 Electric Single Oven

Not finding what you are looking for?
Ovens Logo

Related Topics:

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Ovens Experts

William Miller
William Miller

Level 3 Expert

9179 Answers

Ekse

Level 3 Expert

13434 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Are you a GE Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...