Question about Coffee Makers & Espresso Machines

Open Question

ESAM 5500 Load Test - what does each button mean? what are the EV1 and EV2 and how do you determine a part is malfuctioning?

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
rgall3285

ray gallant

  • 64733 Answers

SOURCE: Delonghi ESAM 5500 no hot water/milk just says "Heating Up, Please Wait"

Apparently the heating element has gone to that place where they can not be fixed .

Posted on Nov 25, 2015

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a delonghi esam 5500 coffee machine keeps tripping the fuse in the fuse box


check how many machines run on that circuit at one time, add up all the watts (on the bottom of the units) divide by the line voltage, this will be amps used, pull the fuse and check the rating, if higher than the amps used the machine is faulty, if lower the fuse may be updated if the cables are rated to take the extra load.

Dec 03, 2017 | DeLonghi Coffee Makers & Espresso Machines

2 Answers

DELONGHI ESAM 5500 WON'T MAKE CAPPUCCINO SAYS GRINDS TOO FINE, BUT WILL GRIND AND MAKE REGULAR COFFEE


have you tried cleaning it as described in your user manual,, can you hit the button for regular grind? there are alternatives, a coffee grinder if failry cheap at 10 dollars US,,

Jun 07, 2016 | DeLonghi Perfecta ESAM5500 Fully Automatic...

1 Answer

Delonghi ESAM 5500 no hot water/milk just says "Heating Up, Please Wait"


Apparently the heating element has gone to that place where they can not be fixed .

Nov 25, 2015 | DeLonghi Coffee Makers & Espresso Machines

1 Answer

Press clean button error message on delonghi ESAM 5500


Hi Susanah
my deLonghi also wants a clean now and then. In your situation I Would disconnect the machine, wait awhile then connect again and see if she still wants a bath or it is an error .
good luck
kolbrun
ps there is always the troubleshooting page in the manual,

Aug 12, 2015 | DeLonghi ESAM5500

1 Answer

My dryer will spin and then stop spining reading err68 or err4a what can this mean.


E4A = The drying time has exceeded program time for cycle. Press Pause Cancel and SELECT buttons for 6 seconds to exit test modes. Position cycle selector to NORMAL, temperature selector to HIGH HEAT and touch START. Check for any thing that would extend dry times such as: no heat, restricted vent, blower fan blade broken or loose, dryer installed in closetwith solid door, or bad connection in moisture sensor bar cir cuit or dirty bars. If dryer operates normally but code returns, replace electronic control.
68 = One of the keys (buttons) is stuck closed (active). Enter function testmode and perform key (button) test to determine which button is at fault. Carefully free the and perform the test again. If button is free but the key struck code still exists, replace electronic control

Dec 31, 2010 | Frigidaire Affinity ATF7000ES Front Load...

1 Answer

TEST MODE IS ON MY SCREEN WHAT DOES THIS MEAN


What does it mean when test mode.is displayed on bt synergy 5500 phone

Nov 28, 2010 | Nokia 5310 Cellular Phone

1 Answer

What does error code e68 mean


One of the buttons is stuck closed or shorted. Enter the function test mode and perform the button test to determine which button is stuck or shorted. When determined which button, try to free or unstuck the button then perform the test again. Replace the user interface board when the button is freed but the code still exists.

Press and hold the SELECT and CANCEL buttons simultaneously for 6 seconds to reset the control. When resetting is successful, the buzzer will sound and "rES" will be shown briefly in the display, and then immediately rotate the cycle selector knob 5 turns in the counterclockwise direction to the second position from the bottom.

Press and hold the OPTIONS and CANCEL buttons simultaneously for 2 seconds to enter test mode; the buzzer will sound 3 times and all of the LEDs will flash rapidly.

Rotate the cycle selector knob 4 times in the clockwise direction to enter button test. Press the buttons one at a time and observe the LEDs corresponding to that button light up. The LEDs should light up; otherwise the button is stuck.

Press and hold the SELECT and CANCEL buttons simultaneously for 6 seconds to exit test mode.

Apr 04, 2010 | Frigidaire Electric Dryer

1 Answer

Malfunction Indicator Lamp


IT MEANS THAT ONE OR MORE OF ABOUT 200 DIFFERENT FAULTS HAS OCCURED IN THE ELECTRONIC CONTROL SYSTEMS OF YOUR CAR, U WILL NEED TO HAVE A TROUBLE CODE TEST RUN TO DETERMINE WHAT IS CAUSING THE LIGHT TO COME ON

Jul 06, 2009 | 2007 Toyota Corolla

Not finding what you are looking for?
Coffee Makers & Espresso Machines Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Coffee Makers & Espresso Machines Experts

Pierre Laplante

Level 3 Expert

2042 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

graybeard32301

Level 3 Expert

382 Answers

Are you a Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...