Question about Honeywell Heating & Cooling

Open Question

Why my Honeywell 2000w goes in overload without to plug in anything

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Manual for trimtech 2000w chain saw


Try Googling (Trimtech)(2000w)(manual) without parens.

Feb 04, 2018 | Garden

1 Answer

Unplug the compressor light and fan worked has the compression got a fuse


Check the start and overload relay if the compressor isn't doing anything that's the first thing I'd try. Usually the overload goes out. Is the white one plugged in over the start relay. Take them both off and shake them. If they rattle replace both. If only one rattles replace the one only. When it's the compressor there isn't much else you can do if the relay and overload aren't bad you can try a 3 in 1 starter but I wouldn't keep using it. Use it to get the compressor running again then reinstall the relay and overload.

Apr 22, 2016 | Refrigerators

1 Answer

My honeywell HFD-015C air purifier wont turn on


Hello, this is Ava with Think Crucial.

You may check to make sure that the power cord is correctly connected to the outlet. Test the outlet is functioning properly using another appliance or lamp. Also, check the fuse or circuit breaker. The outlet may be overloaded if other appliances are also in use. Establish and correct the cause of the overload. If none of these works, then there is something wrong with your purifier unit and contact the store where you purchase it or Honeywell for replacement. It is advised not attempt to repair the unit yourself.

You can purchase a wide variety of high-quality Honeywell replacement parts for your Honeywell air purifier direct from Think Crucial with free shipping and an exclusive 10% coupon for Fixya.com readers, use code: FIXYA10

https://www.thinkcrucial.com/search?type=product&q=honeywell

I hope this was helpful.

Ava B.
Think Crucial Customer Care
http://www.thinkcrucial.com/

May 31, 2014 | Honeywell 17000 Air Purifier

1 Answer

Honeywell air purifier won't turn on


Hello, this is Ava with Think Crucial.

You may check to make sure that the power cord is correctly connected to the outlet. Test the outlet is functioning properly using another appliance or lamp. Also, check the fuse or circuit breaker. The outlet may be overloaded if other appliances are also in use. Establish and correct the cause of the overload. If none of these works, then there is something wrong with your purifier unit and contact the store where you purchase it or Honeywell for replacement. It is advised not attempt to repair the unit yourself.

You can purchase a wide variety of high-quality Honeywell replacement parts for your Honeywell air purifier direct from Think Crucial with free shipping and an exclusive 10% coupon for Fixya.com readers, use code: FIXYA10

https://www.thinkcrucial.com/search?type=product&q=honeywell

I hope this was helpful.

Ava B.
Think Crucial Customer Care
http://www.thinkcrucial.com/

Apr 23, 2014 | Honeywell UV HEPA Clean Antibacterial Air...

2 Answers

2000 watt cobra inverter keeps saing olp, overload


2000w means is out off rang load 2000w plus then alarm beep have running.

Mar 24, 2009 | Cobra CPI 1000 DC to AC Power Inverter

1 Answer

When i plug the heater in it does not work.


its difficult to make a homeowner an expert in troubleshooting his/her equipment if he/she has no technical background - but - I will try. First check the cord to plug connection. Is it tight? Does it look melted? Next, take the unit apart where the cord goes into the unit. Check the wiring path. Look at each connection. Look for burnt off wires at connections. Most connectors are the push on type and are mechanically fastened to the wires. if they are burned off you'll need replacement spade terminals and a crimping tool. (radio shack) has these. one wire will go through a thermostat and out to an element terminal. one wire may go through a thermodisc overload, then to the thermostat and then to the element. the other wire will definitely go straight to the element. there may be some extra connections for lights etc. if you have to take apart the heater make a diagram of which wires go where. use some masking tape with numbers written on it to make sure the wires go back to the same place you took them off.

Nov 21, 2007 | Honeywell HZ614 QuickHeat Baseboard Heater

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honeywell Heating & Cooling Experts

Bill Long

Level 3 Expert

606 Answers

Paul Carew

Level 3 Expert

3480 Answers

Cindy Wells

Level 3 Expert

6049 Answers

Are you a Honeywell Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...