Question about Coffee Makers & Espresso Machines

Open Question

Reattaching brew pipe on an aequator Brasil coffee machine

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 25 Answers

SOURCE: Keurig starts & stops without brewing coffee, just descaled

The pic is clogged with coffee or the air bladder is bad. Use the tool on the underside of the tray to clean out pic. If that doesn't work, the bladder will be bad.

Posted on May 14, 2009

Ad

NORMAN ZINK

  • 85 Answers

SOURCE: cuisinart Coffee on Demand?12-Cup Programmable Coffee

Hello crystalmeikl,
This is a really common problem with the cuisinarts. I am most familiar with the DCC-1200, but you may be able to solve the problem. The may be an indication that something is plugged up. Open the top of the unit and in one of the corners you should find a water filter stick or column that is removable. Pull it out and open it up to clean out the clogged up carbon filter in there. (You can later buy a new filter on Amazon.) Clean out the debris from the bottom of the cavity. Replace the stick into the cavity once cleaned. Now it's time to run through a solution of 2 parts water and 1 part vinegar. Do this once or twice with fresh solutions, then with a pot of fresh water. When the filter stick is plugged up the sensor says its time to clean it or shuts the unit down, but most people don't know about this fix. I hope this is helpful to you, crystalm. Positive feedback is appreciated. Good luck. NormanZ

Posted on Jul 11, 2009

Anonymous

  • 13 Answers

SOURCE: The "Brew Pause" feature doesn't work

It's the spring part on the bottom of that black basket. Now that it's broken there's really no fixing it. The only thing to do is call the manufacturer (800-726-0190) to get a new brew basket. They are open on weekends, so you could call them today and see what they can do (brew baskets are covered under the 3 year warranty, btw). Just have your model and serial number and you can probably have a new one ordered in less than 5 minutes. :)

Posted on Aug 29, 2009

Testimonial: "Very helpful suggestion to call the manufacturer. I was told to try the self-cleaning, as calcium deposits could be the problem. worked like a charm."

Anonymous

  • 60 Answers

SOURCE: my coffee machine won't brew

Without opening the item up you would not be able to cure it. Unplug it, take cover off and have a look to see if you can see a blockage or a reset betton for the element.If not you may want to replace it or get your item repair via a engineer.

Posted on Dec 05, 2009

FixyaMarsha

  • 5 Answers

SOURCE: We pour the water into

It sounds like it is clogged.
In the manual it explains how to descale with white vinegar. Another thing to do is to take a straightened paper clip and unclog all openings where water goes through. Taking out the k-cup holder and cleaning is also recommended.
Keurig 866-901-2739 will walk you through these steps. They are very nice and this is what I did when I was having trouble with mine.
Good luck.

Posted on Feb 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Water leaks out under the brew group when brewing coffee


maybe you have to change the small thing which is like a pipe on the brew unit

Oct 21, 2013 | Saeco Magic Comfort Plus Espresso Machine

1 Answer

Gevalia 12 cup coffee maker slow brewing


The pipes are blocked with build up scale or water dirt. You can try to descale the machine by adding in the water half cup of lemon juice and brew it without coffee leave if for 20 min and the clean it by brew it with fresh water these will make a diference then try this again in a week.

May 16, 2012 | Gevalia CM-500 12 Cup Coffee Maker

1 Answer

My machine mark alternativley ventilate and fill water tank. I ventilate and I fill the machine and the message don't dissapear. With this display, I can't make any coffee. My email :...


Hi,
Remove the bottom of the coffee maker, identify two rubber tubes and check to see if one has come loose or is simply not on tight. A simple reattaching of one of the tubes will work.
Another reason could be draining hole getting clogged with coffee grounds. When this happens it is easily fixed by removing the brew group and overflow tray; find the small drain at the back that drains excess water into the overflow tray and opens it up with a pipe cleaner or tooth pick. Flush out any coffee ground behind that hole.

Hope this helps.

Shane

Mar 06, 2011 | Saeco Spidem Trevi Digital Plus Fully...

1 Answer

Saeco Vienna coffee when the machine starts the coffee dispensing


Is it leaking only when brewing coffee ?

If not I would check the seal under the water tank (Part #NM05.006)

If so, I would check the following:

1- The water input port on the back of the brew unit (looks like a smoke pipe) might be clogged

2- The o-ring of the water tubes coming in and out of the boiler.

Jul 30, 2010 | Saeco Vienna SuperAutomatica Coffee...

2 Answers

The liquid coffee isn't coming through. I get wet pellets in the disposal container. The steamer seems to work OK.


Hi Brew head cleaning Vienna/ Master Remove the brew unit. Holding the handle, the top left side is the brew head. There is an outlet pipe that exits the front side towards the door (looks like a long "L" pipe). 2screws hold it to the top. Remove the 2 screws while holding the manifold ("L" pipe assembly). Once they are removed, lift the l assembly off (be careful, there is an O-ring, spring and at the end a black rubber disk. Now remove the brew screen, by holding the screen with your finger and twisting the thumbscrew (remember, thumbscrew), DON'T use the key to install the screen, use your fingers. Once the screen is out look at where the screen was. There are 2 holes. A big one in the center and a small one to the side. With the brew unit upside down over the towel, insert a paperclip into the small hole and force anything out the other side. I have gotten worms almost a 1" long from this passage. The paper clip has to go from this side to prevent damage to the seat on the other side. Clean then reassemble. Brew unit on towel right side up. Drop the crystal ball in first. Then the spring small end first on the crystal ball. Now the O-ring over the spring, then place the manifold on top of that with the pipe towards the machine. Insert your screws (I turn them backwards a little with a little downward pressure until they feel like they drop into the threads. They should turn down easily, if not back them up a little more ( we are trying to find the old threads) and tighten. Install screen, and tighten with your fingers. The screen just needs to be flush with the bottom of the brew head. That should do it.

Feb 12, 2010 | Saeco Vienna SuperAutomatica Coffee...

1 Answer

Saeco Odea Giro Plus spare parts needed


The coffee dispensing valve is available at your saeco dealer 1-2 hr job to change...

Sep 27, 2009 | Saeco Odea Giro Plus Coffee Maker

3 Answers

Reads decalcify, brew unit missing- and wont make coffee!


Hi
Open you door on the right. Push on the upper left side of your brew unit and see if it will click. You have to push fairly hard towards the center of the machine. If it clicks the outlet pipe needs to be lubricated. The outlet pipe is the angled pipe on the top left side of the brew unit in the back. Lube the end of the pipe with food grade not food based lube.

Apr 27, 2009 | Saeco Royal Digital Plus Coffee...

2 Answers

Coffee not coming out of the front taps, coffee & waste beans both ending up in the waste tray, can you please advise thankyou. model type 889


I had the same problem. The pipe that delivers the coffee brew is plugged, therefore, the brew leaks back in the waste tray. You need to take the top cover only. Then you will see a silicone hose. You need to pull the hose out of the head pipe. You can remove easily the head pipe as it snaps on the pipe that delivers the brew. What I did was to run the descaling program. Then inserted a thin stiff wire during the cleaning process and gently pushed the wire a few times to remove the obstruction. You have to be careful. Once the obstruction is cleared steam or liquid will come out of the pipe with some pressure. Then stop the cycle and run it again once the head pipe and top cover are replaced. Although there are no electrical wires visible when you take the top cover you need to be careful and wear rubber gloves and goggles. This worked for me and it was probably due that the machine was not used for sometime and the coffe brew plugged the delivery pipe. Good luck

Mar 01, 2009 | Krups Orchestro 889 Espresso Machine

1 Answer

No coffee


Hi,

Make sure the water pipe not is broken.
If you take out the brewing unit and look at the chassis on the machine, you can see a hole, there should be a little plastic pipe comming from the machine down to the hole. If this is broken then the water will go to the driptray.

/Mirran

Aug 14, 2008 | Saeco Vienna De Luxe Espresso Machine

Not finding what you are looking for?
Coffee Makers & Espresso Machines Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Coffee Makers & Espresso Machines Experts

ThaMp3Doctor
ThaMp3Doctor

Level 3 Expert

8597 Answers

Pierre Laplante

Level 3 Expert

2042 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

Are you a Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...