Question about OKI Office Equipment & Supplies

Open Question

OkI C5800 error 923. I replaced the black drum and after turning the printer on/off get the same message. Is this a K-ID motor problem?

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 141 Answers

SOURCE: Oki c5800 laser printer

http://www.c5800.co.uk/index.asp?printername=C5800&menumode=0&content=C5800downloads

At the bottom you will see the file C58uEN1.pdf

Go to page 89

Posted on Mar 26, 2008

Ad

Anonymous

  • 449 Answers

SOURCE: OKI C5800 ERROR MESSAGE- DRUM

hi!!!
try to check the drum first!!!
clean it with the dry tissue?
there a lifespan of the drum
i have the same problem with that.
my drum capacity is only 30,000 copies
so then i replaced it! and works fine now

so try to replaced the drum it might on it capacity
or clean it

try to email me ronaldsuboc@gmail.com

Posted on Sep 19, 2008

Anonymous

  • 1 Answer

SOURCE: Have an OKI Printing Solution

Found this at Fixyourownprinter.com

1. Turn machine on while pushing and holding the TWO up/down menu buttons at same time.
2. Menu window will show "OKI USER"
3. Scroll to " Engine Dialog Mode" is indicated. Push Enter button.
4. "Diagnostic Mode xx.xx.xx S-Mode is indicated.
5. Scroll to "NV-Ram initial" is indicated. Push ENTER.
6. Window shows "NV-Ram- Initial Table 1".
7. Push ONLINE and ENTER Buttons simultaneously and HOLD for 10 seconds after you see "Executing Reset" appear in menu window.
8. Restart printer.

All toner, drum, fuser and transfer figures return to 100%.

Worked for me when I had the same error. Hope it helps.

Posted on May 26, 2009

Jeff Hughes

  • 97 Answers

SOURCE: have a oki c9800 ...gives error 923

923: Error - Black Image Drum Lock Error
The K ID unit is not operating
properly.

Check to confirm that Image Drum is seated properly.
Check to confirm that the K ID
unit is in position.
Replace the K ID unit.
Replace the K ID motor.

Posted on Mar 29, 2010

Twix Blitz

  • 5 Answers

SOURCE: My Oki C5800 is not printing any black- toner is

First of all try cleaning the black LED head with an alcohol wipe, next check the connection to the black LED head and make sure there is nothing blocking the light between this head and the top of the image drum. It may also be worth swapping the LED head between colours to see if the problem moves colour or stays with black. If after moving the head the problem still happens with black then it may indicate a problem with the image drum or an electrical problem. If you have another unit you could try swapping the drum and toner between units.

Posted on Nov 10, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Oki C5800 is not printing any black- toner is not out, drum is new. I have restarted computer, turned off/on printer, checked cables- not giving any messages. Help?


First of all try cleaning the black LED head with an alcohol wipe, next check the connection to the black LED head and make sure there is nothing blocking the light between this head and the top of the image drum. It may also be worth swapping the LED head between colours to see if the problem moves colour or stays with black. If after moving the head the problem still happens with black then it may indicate a problem with the image drum or an electrical problem. If you have another unit you could try swapping the drum and toner between units.

Aug 25, 2011 | OKI C5800Ldn Led Printer

2 Answers

FATAL ERROR 923


923 - black image drum lock error

make sure the black drum is in correctly

make sure black toner is locked

reboot machine

Feb 16, 2010 | OKI C5550N Multifunction Printer - Color...

1 Answer

Have a oki c9800 ...gives error 923. have replaced the motor unit for black image drum but it prints some pages and gives the error again


923: Error - Black Image Drum Lock Error
The K ID unit is not operating
properly.

Check to confirm that Image Drum is seated properly.
Check to confirm that the K ID
unit is in position.
Replace the K ID unit.
Replace the K ID motor.

Dec 10, 2009 | OKI C9600hdn Laser Printer

1 Answer

Toner sensor error on an Oki C3520 Laser


Check the little switch/door on the right hand side of the drums.
This has worked successfully for me.

Symptom:
After replacement of a C3530 Image Drum, the message, "Toner Sensor Error" is displayed.

0.10a?openelement&fieldelemformat=gif




Cause:
The plastic shutter in the ID is fully or partially covering the toner sensor window.




Resolution:
Move the cover upward to allow for the sensor to become fully exposed prior to reinstalling the drum.

0.106?openelement&fieldelemformat=gif











moz-screenshot-2.jpg

Oct 18, 2008 | OKI Electric Industry C3520 Laser Printer

1 Answer

OKI C5800 ERROR MESSAGE- DRUM LIFE 10972


hi!!!
try to check the drum first!!!
clean it with the dry tissue?
there a lifespan of the drum
i have the same problem with that.
my drum capacity is only 30,000 copies
so then i replaced it! and works fine now

so try to replaced the drum it might on it capacity
or clean it

try to email me ronaldsuboc@gmail.com

Sep 18, 2008 | OKI Office Equipment & Supplies

1 Answer

Have an OKI Printing Solution C5800 color printer received the following error message: Check Toner cartridge 543K Toner Sensor error - have already changed the Drum and the toner. The error will not go...


Found this at Fixyourownprinter.com

1. Turn machine on while pushing and holding the TWO up/down menu buttons at same time.
2. Menu window will show "OKI USER"
3. Scroll to " Engine Dialog Mode" is indicated. Push Enter button.
4. "Diagnostic Mode xx.xx.xx S-Mode is indicated.
5. Scroll to "NV-Ram initial" is indicated. Push ENTER.
6. Window shows "NV-Ram- Initial Table 1".
7. Push ONLINE and ENTER Buttons simultaneously and HOLD for 10 seconds after you see "Executing Reset" appear in menu window.
8. Restart printer.

All toner, drum, fuser and transfer figures return to 100%.

Worked for me when I had the same error. Hope it helps.

Aug 08, 2008 | OKI Office Equipment & Supplies

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top OKI Office Equipment & Supplies Experts

WTF Chuck.....
WTF Chuck.....

Level 3 Expert

387 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Ekse

Level 3 Expert

13434 Answers

Are you an OKI Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...