Question about Measuring Tools & Sensors

Open Question

5in1 acurite will not display the outside temperature and feel like temperatures.

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 7 Answers

SOURCE: OUTDOOR TEMPERATURE

Please check the following website for all the info and faq.

http://skyscan.info/content/index.php?option=com_content&task=view&id=35&Itemid=40

Also,

If you have lost the outside temperature on the clock display after replacing the transmitter battery then do the following:

1. Make sure you have good batteries installed in the remote transmitter
2. Remove the batteries from the main clock and keep them out until the clock display disappers.
3. Re-install the batteries in the clock.
4. Wait until the display returns and includes the outside temperature display as well.
5. Set the clock again for current time/date etc.
6. Bingo. You are in business.

Posted on Dec 19, 2008

Ad

Anonymous

  • 2 Answers

SOURCE: Remote Sensor

make sure your time is set and the atomic clock time is recieved, then leaving the rear cover off of the transmitter, push the "tx" button not the "c/f" that is just for centegrade or ferenhight. you will see the red light on the front of reciever flash in a few seconds. The temp should display on your clock screen. If not, did the red l.e.d. light on transmitter flash. If not, its not sending data to clock. I have to reset and hit transmit every time I replace batteries on transmitter. Had no problems for over 2 years of using outside. If your not getting a reading with transmitter sitting next to clock after hitting "tx" button you may have defective transmitter.

Posted on Jan 18, 2009

johnjohn2

Johnny Brown

  • 5763 Answers

SOURCE: The outside air temperature sensor for the 2003 Camry

the sensor is located in front of radiator if you open hood and look down behind front bumper you should see it, or look from under the frt bumper, it easy to change, also get part from dealer it not $$,hope this helps.

Posted on Nov 28, 2009

Testimonial: "Thanks-- I found it."

Anonymous

  • 1 Answer

SOURCE: acurite 1097-rx will not display outside temp or

I had same problem. Take all batteries out of both units. Put the batteries in the remote sensor FIRST. Then put batteries in the main unit. Within five minutes, they will link up. Problem solved!

Posted on May 11, 2010

satitus

steve titus

  • 277 Answers

SOURCE: Display - outside temperature and compass

The overhead console is quite prone to internal failure. Dim, intermittent, or dead displays are a common symptom of an internal failure. We offer a reasonable repair service with a lifetime guarantee. Check it out: www.autoclockrepair.com

Posted on Aug 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My acurite 00509 has stopped giving me the correct temp reading. I've put another temp gauge next to it and acurite shows 78* and my othergauge shows 72*. Do I need to return it or what ? Thanks


The indoor temperature and humidity and outdoor temperature readings can be calibrated on the display to improve accuracy. Calibration can improve accuracy when sensor placement or environmental factors impact your data accuracy. 1. To access calibration mode, press AND HOLD the "?", "?", and "SET" buttons for at least 5 seconds. 2. Once in calibration mode, the preference you are currently setting will be highlighted on the display. 3. Press the "?" or "?" buttons to calibrate the data value higher or lower from the actual reading. 4. Press the "SET" button to confirm the calibration adjustment. The " " icon will remain illuminated next to calibrated values. 5. The next adjustable data will begin flashing, indicating it is ready to be calibrated. Repeat Steps 1 - 4 to calibrate additional data. The preference set order is as follows: OUTDOOR TEMPERATURE INDOOR TEMPERATURE INDOOR HUMIDITY BAROMETRIC PRESSURE (must be set to MANUAL mode; see page 12) After 20 seconds of inactivity, the display will save the adjustments and exit calibration mode. Note: Calibrations will be erased if the display is reset or if batteries are removed and the power adapter is unplugged.

Oct 02, 2018 | Acu-Rite Acurite Wireless Weather...

1 Answer

Flashing emblem by outside temp on acurite


The symbol probably is indicating that the outside transmitter is sending temperature data.

May 22, 2017 | Measuring Tools & Sensors

2 Answers

Why can't I receive input from the outside sending unit?


Make sure that all the batteries are good!!
This procedure outlines the typical process to pair the sensor and base.
Base Station Battery Installation

·Remove the printed vinyl label from the LCD screen of the base station
·Position the remote sensor near the base station
·Open the battery compartment at the back of the base station and insert (2) AA batteries according to the polarity markings. Replace the battery compartment cover.
·Within a short time the RF signal icon (located to the left of the outdoor temperature channel indicator) will start flashing. This indicates that the base station is ready to pick up the RF outdoor temperature signal from the remote sensor. It will continue to flash for 3 minutes or until the signal from the remote sensor is detected.

Register the Remote Sensor
·Open the battery compartment at the back of the remote sensor and slide the channel selector switch to your desired channel. For the first remote you may select any channel, for additional remotes select any unused channel
·Insert (2) AAA batteries according to the polarity markings. Be sure to install the batteries in the remote within the time that the RF signal icon is flashing on the base station. 1541 WeatherGuide Wireless Weather Forecaster with Barometer

Jan 07, 2016 | Measuring Tools & Sensors

1 Answer

OUTSIDE TEMP SENDING UNIT GOT WET AND WILL NOT CONNECT TO CLOCK. HOW CAN I FIX OR HOW CAN I REPLACE?


[PDF]WS-8117 ATOMIC CLOCK WITH OUTDOOR WIRELESS ...

https://www.lacrossetechnology.com/products/.../misc/8117-manual.pdf
NOTE: Do not set the clock until the outdoor temperature is displayed. .... The unit will still try and receive the signal every day despite it being manually set. ..... sunlight, extreme cold and wet/moist conditions as these will lead to rapid changes ... Beforesending the atomic clock in for repairs, contact La Crosse Technology.

La Crosse Technology Top Solutions

https://www.lacrossetechnology.com/support/top_solutions.php
A: Complete a restart for display with the temperature/humidity sensor: ... to rest for 15 minutes can result in failure to connect with the outdoor sensor or missing ... Products set outside of these time zones will not search for a WWVB signal as it is ... locate the Clock or Weather Display near an outside wall and point the unit in ...

Common issues weather stations: Click Here

www.weather-station-products.co.uk/faqs/common-issues-weather-stations
Under £30 £30-£75 £75-£125 From £125 Birdhouses/Feeders Outdoor Clocks ... I'mnot getting any outdoor readings from my outdoor sensor, what do I do? This willcure 90% of all sensor connection problems, important you must ... is the airtemperature, to get this reading you need to place the unit away from direct sun.

Replacement Temperature Sensor ' AcuRite

www.acurite.com > All products

Dec 16, 2015 | Audio Players & Recorders

1 Answer

I have model 00606TX. I had to replace the batteries on both components but cannot get the outside temperature to register on the display. I checked that the batteries were installed correctly and t


Hi Stephanie!

We would need the model number of the main display unit to give full instructions or you can visit; http://www.acurite.com/kbase
and enter that model number for troubleshooting tips and steps.

Nov 22, 2014 | Measuring Tools & Sensors

1 Answer

Why is the outside temperature not displaying on the base?


After a battery replacement, the outside and inside units have to "talk" to each other before you can get a display. Also, the outside unit's batteries have to be replaced first. You should not press any buttons for 10 minutes until the two units have finished "talking"

Jan 24, 2013 | AcuRite Acu-Rite 00593W Wireless Weather...

1 Answer

How to reset my Acurite 1099rx after replacing battery


http://www.acurite.com/advancedsearch/result/?q=1099RX

There is no reset button, installing new batteries causes the sensor to reset itself.

Try removing and re-installing the batteries.

Good luck,
Steve

Jan 15, 2013 | Measuring Tools & Sensors

Not finding what you are looking for?
Measuring Tools & Sensors Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Measuring Tools & Sensors Experts

Vuk B

Level 3 Expert

717 Answers

Brad Brown

Level 3 Expert

18127 Answers

Tom Chichester

Level 3 Expert

54965 Answers

Are you a Measuring Tool and Sensor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...