Question about Televison & Video

1 Answer

I need the user manual for the zrc-102 remote control. Trying to download it

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Televison & ... Master
  • 6,046 Answers

Do you mean the Dynex ZRC-102 remote control? This remote was included with the Dynex DX-LCD19-09 and a few other models and is not apparently a universal remote control. The guide to the remote is usually included in the manual for the electronic device that the remote came with. The best source for the manual is ManualsLib, https://www.manualslib.com/manual/41507/Dynex-Dx-Lcd19-09.html#manual . Pages 5-6 describe using the remote: https://www.manualslib.com/manual/41507/Dynex-Dx-Lcd19-09.html?page=5#manual . Unfortunately, the manuals here, https://www.dynexproducts.com/pdp/DX-LCD19-09/8632848 , are not readable by my Windows computer. I don't have a Hex or Octet reader installed.

I hope this helps.

Cindy Wells

Posted on Oct 05, 2019

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

marionbagget

  • 718 Answers

SOURCE: my volume control on remote doesnt work

Try the following first;

Step 1- Pull the batteries out of the remote and leave them out until Step 4.
Step 2- Press and release each and every button one at a time on the remote control until every button has been pressed and released at least once!
Step 3- If your remote has slide switches, you must move the switch to each position then repeat the button pushing in Step 2.
(When you're done, be sure to put the slide switch in the correct position to operate the unit the remote came with!)
Step 4- Put the batteries back into the remote, being very careful to install them correctly.
New batteries should be used if you're not sure about the old ones.

If you are still having problems, you should return the unit to the place of purchase for a replacement.

Posted on Mar 13, 2009

memturbo

mark gardner

  • 234 Answers

SOURCE: Manual Download

here ya go

Posted on May 12, 2009

SuperComputr

  • 19 Answers

SOURCE: i need the code the

Download this PDF for Dynex TV codes, look for the table of common codes, then simply copy it and enter it.

Posted on Jan 11, 2011

E-dude 100

  • 1 Answer

SOURCE: when I click chanel up or down the tv says please

For the Dynex ZRC-102 remote control channel switching.

1. Press the MENU button and select SETUP.

2. Go down the list and select FAVORITE CHANNEL MODE and switch it to OFF.

The +/- CHANNEL buttons will then switch channels when pressed.

Posted on Feb 19, 2011

brian soufane

  • 693 Answers

SOURCE: Need User Manual & Remote Control

I set up this link that will take you to download your When you get scroll down and select there, select download

http://www.manualowl.com/m/Phillips/FW-C579/Manual/163091

Posted on Feb 05, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Reprogram A DYNEX ZRC-102 Remote Control


If your Dynex remote can't control your Dynex TV, you need to try replacing batteries and testing operation. If no success, the remote or the sensor in the TV may have failed.

Aug 16, 2016 | Dynex Televison & Video

1 Answer

How do I troubleshoot a Dynex ZRC_102 remote control


Check the remote control for its infra-red emission. Check it with fresh batteries. Check by pressing all the buttons on it; and see whether all of it generates infrared signal while pressing. If it is found OK, check and replace the infrared sensor inside the TV. If you wish to get some details; check the site linked here. It has details about how to check a remote control; by one among the post. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/ If the remote control is found OK; check and replace the infra-red sensor inside the TV. Contact any service technician

Nov 23, 2014 | Dynex ZRC-102 Remote Control...

1 Answer

Please wait is stuck on screen.


Reboot.
Push and hold the power-on button for about 20 sec. The computer should shut down and allow you to restart.

Apr 13, 2013 | Dynex ZRC-102 Remote Control...

1 Answer

Program my insignia zrc-101 remote


Your Insignia remote already contains the codes. The instructions for your remote will tell you whether there is a code available for the device you want to control (TV, etc).

Dec 02, 2012 | Insignia New Original ZRC101 Remote...

2 Answers

I need the code the to my tv so i can program my zrc-102 remote to my dynex tv


Download this PDF for Dynex TV codes, look for the table of common codes, then simply copy it and enter it.

Jan 11, 2011 | Televison & Video

1 Answer

When I click chanel up or down the tv says please


For the Dynex ZRC-102 remote control channel switching.

1. Press the MENU button and select SETUP.

2. Go down the list and select FAVORITE CHANNEL MODE and switch it to OFF.

The +/- CHANNEL buttons will then switch channels when pressed.

Sep 28, 2009 | Televison & Video

1 Answer

My volume control on remote doesnt work its a dynex zrc-102 remote control how do i get a code or what do i need to do so i can ajust my volume from my remote control


Try the following first;

Step 1- Pull the batteries out of the remote and leave them out until Step 4.
Step 2- Press and release each and every button one at a time on the remote control until every button has been pressed and released at least once!
Step 3- If your remote has slide switches, you must move the switch to each position then repeat the button pushing in Step 2.
(When you're done, be sure to put the slide switch in the correct position to operate the unit the remote came with!)
Step 4- Put the batteries back into the remote, being very careful to install them correctly.
New batteries should be used if you're not sure about the old ones.

If you are still having problems, you should return the unit to the place of purchase for a replacement.

Mar 13, 2009 | Dynex 32 in. LCD Flat-Panel HDTV

2 Answers

NSE URC11C-8 REMOTE


Book Can Be Downloaded Here
http://www.remotecentral.com/cgi-bin/files/rcfiles.cgi?area=other&db=devices&br=nse&dv=universalremote&md=urc11c8&kw=&st=&ar=&dt=&so=&pg=1&file=others/nse/urc11c8-manual.zip

Jan 06, 2008 | Philips PM3S Remote Control

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76171 Answers

Cindy Wells

Level 3 Expert

6046 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...