Question about Behringer Music

Open Question

I have a Behringer Xenya 1202 FX Mixer the effects will not light up or work, any Ideas to fix the effects.

This is a live studio mixer

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Fred Yearian

  • 5603 Answers

SOURCE: my effects on the behringer djx 700 dj mixer stop working how

This is a wild educated guess.

I repaired a Behringer guitar amp that had a DSP effects in it (BX1200 I believe).

The effects were on a seperate board and the board had its own 5 volt power supply. The filter capacitor for the 5 volt power on the board was UNDERSIZED and it had degraded causing the 5 volts to drop out of regulation, dipping to 4 volts. This caused the DSP effects to fail.

YOUR device MAY use the same DSP OR design.

Check the 5 volt power with an OSCILLOSCOPE to look for dips below the 5 volt operating point that occur at 120 HZ.

Posted on Oct 24, 2009

Ad
joelxb

joelxb

  • 30 Answers

SOURCE: I just purchased A behringer PMP4000. It has built

Check the FX to main level to make sure it is not too high. Also check the main FX fader level. Try turning each of these down and see if that corrects the issue. The FX fader should control the volume level of the FX globally (mon sends as well as main outs), and the FX to main should only affect the mains output. Make sure FX to mon1 and FX to mon2 are turned all the way down.
Also check what FX program your using and that the FX IN button is depressed, try starting w/ #10 (small room) and see how that sounds.

Posted on Feb 28, 2011

Testimonial: "Thanks, I'll give it a try and see how it goes."

Fred Yearian

  • 5603 Answers

SOURCE: Can I use a footswitch

Sorry, the Xenyx1202FX does not have a footswitch input. I would suggest if this function is needed to use an external FX unit which has a footswitch input.

Posted on Apr 26, 2011

Fred Yearian

  • 5603 Answers

SOURCE: have a Behringer 1202 Xenyx

You are running your balanced cable into a windows 7 PC? What interface are you using... not the line input on the PC I hope as it is NOT balanced... it is Stereo input with UNBALANCED input. If you tie the mixer using a balanced to 1/8 inch balanced connector you will get plenty of hiss since you are driving the stereo channels oppositely. For high quality, get a good audio interface that runs on the USB of the PC. If you can tolerate a bit of noise but wire it correctly, then you will need to use two UNBALANCED lines out of the mixer for L and R and merge them to a stereo 1/8 inch plug for the PC.

Posted on Jul 11, 2011

Doomface

Lindsay Miller

  • 87 Answers

SOURCE: I have a Behringer xenyx

Hi,

Sounds very much like the control knob is dirty, needs a good cleaning!

Sometimes just giving the knob a good exercising (turn it up and down quickly a few times) can help it.

Some cleaners can leave behind a residue and make it worse, so ask at an amp repair place what product is best to use.

Hope this helps!

Posted on Jul 14, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Studio master diamond pro 16-3 mixer has noisy output what is the complaint?


You may need a ground wire between the mixer and amp

Oct 19, 2015 | Music

1 Answer

Im Using Acid Music Studio 8.0 With & Xenyx502 Mixer. Every Time I Record It Sounds Fine But When I Play It Back When Im Finished Its Off Beat How Do I Fix This??


check the "buffer" setting - set to the lowest number possible. You can't eliminate the "latency" but you can reduce it a lot. Also 0 try to monitor what you are recording with "live" sound (input instead of output) - also, you may need to download a different driver for your audio card, try ASIO4ALL

Oct 13, 2013 | Lexicon Alpha Personal Recording Studio

1 Answer

I have two. One main and one slave. When I use with live band after 15mins the system frozen. Please help me


Let's cover a few basics... these are in the form of questions for you to check:
1. Are the units linked?
2. Do both mixers have the same revision firmware?
3. Do ALL interconnected pieces of equipment such as amps, recorders, these mixers, etc. ALL get power from ONE receptacle OR power conditioner module? Yes, that means running extension cords between the amps and the mixer and the COMMON point of power source. All the pros know to do this to avoid ground bounce and electrical noise and equipment suddenly going offline..
4. Are ALL of your interconnecting cables BALANCED lines, either XLR or TRS cables?
5. Are there NO mono devices plugged in which are not first fed through a DI box?
6. Are you taking precautions against static discharges like rugs or using Staticide on rugs in the control room?

When you can answer YES to all the above basics, then let's go further with troubleshooting... The first step would be to swap the units to look for ANY change.

Sep 06, 2011 | PreSonus Audio Electronics PreSonus...

1 Answer

How do you connect behringer sx2442fx eurodesk sttudio mixer on acomputer in studio


WIthout a quality audio interface the answer is you don't... You need to procure an audio interface for the computer. The internal audio systems of computers are too noisy to get decent results. The manual for the mixer will show the typical studio connection with a suggested audio interface.

Aug 06, 2011 | Behringer Sx2442fx Eurodesk 24channel...

1 Answer

When i record thru my mxl genesis mic with the mixer i get like a loud distorton. Im using magix 14 ,and i have downloaded the audio driver off the disc that came with the mixer....Help


It is likely you do not have the levels set correctly and are over driving the mixer. Reduce the trim settings using the PFL buttons and monitor the level indicators to insure you are not clipping.

With a condenser mic you CANNOT have any speaker in the room that the mic can hear of course. These mics are so sensitive. Your mixer and monitor speakers and recording will be in a separate room from the soundproof studio typically.

To monitor the system anywhere in the same room as the mic you MUST use headphones that do NOT leak sound or you will get feedback and distortion.

Mar 14, 2011 | Behringer XENYX 2442FX Mixer

1 Answer

Pls, i will like to know how i can get a pro sound with my beringer b2pro mic with my xenyx 1204usb mixer. i mean mic settings


The mic will give very good sound assuming you put it in a studio environment and have no speakers being driven by it that the mic can "hear" or it will feedback instantly.

Your studio should have proper sound deadening on the walls ceiling and floor. There is a lot of information on the web about setting up a studio. Search for it with google. The more studio-like the environment, the more like pro sound you will get. You will NOT get pro-sound in a bare garage or a room in a house without handling the sound reflections in the room. These mics hear EVERYTHING... they are a high quality mic.

Feb 25, 2011 | Behringer B2PRO Gold-Sputtered Large...

1 Answer

You can not play these drums live the spill of the fold back drum fill bin sets of the snare trigger ive turned down the sens on the red box still doesnt work a big waste of money i need to talk to...


With this kit being acoustic-electric, the only advice I can give is to disconnect your snare trigger and mic the snare. It's either that, or your snare trigger is faulty. A new trigger is going to cost about the same as mics, but mics won't hit your snare, making you sound inexperienced. For miking the snare, you'll want to get two mics, placed on the top and bottom head. Try to position them on the same spot on the rim to avoid voicing problems. Studio drummers do the same thing when recording.

For playing this way live, you'll want to use either the main PA, or run to a separate mixer so you can control the volume of the snare in relation to the rest of the kit.

Hope that helps!

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/cameron_463100ffd54b591d

Feb 11, 2011 | Pearl E-Pro Live Electronic Acoustic Drum...

1 Answer

Can't get any gain without feedback when using my new shure sm81 mic and the xenyx x1240usb fx mixer. keep the speaker way out in front of me. no montiors. using just a hair of reverb and compression. have...


This is a STUDIO mic and CANNOT be used in the presence of speakers that are driven from its output.

There is special hardware processors to cancel feedback but you do NOT want to go there !!!

This condenser mic is to be used in a studio where performers wear earphones and NO monitors are present.

You should use a Shure SM58 or other CLOSE talking cardoids if you have speakers in the area.

Jun 09, 2010 | Behringer Xenyx 1002fx Mixer 10 Input 2...

1 Answer

WDM Driver failed to install is the first of four


Make sure you verify that your computer meets the requirements for the Omega. I have one of these and it installed on an XP with no problem.

Maybe you have Vista instead of XP. OFTEN there are incompatibilities of Vista. If you have that or heaven forbod Windows 7, you may either need a different WDM or have to backstep to the XP operating system.

In short, VERIFY the requirements of teh Omega and its software with the OS and system you are trying to install it on.

A last thing to try is to install it while in "SAFE MODE".

Nov 13, 2009 | Lexicon Omega Desktop Recording Studio

Not finding what you are looking for?
Music Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Behringer Music Experts

Michial Gueffroy

Level 3 Expert

1140 Answers

Chickenwatt

Level 1 Expert

18 Answers

Ric Weide
Ric Weide

Level 1 Expert

10 Answers

Are you a Behringer Music Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...