Question about Pool & Spa

1 Answer

My hot tub spa has power on all three terminals even when not turned on

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Pool & Spa Master
  • 10,790 Answers

Possible relay stuck on

Posted on Oct 19, 2019

Ad

5 Suggested Answers

Anonymous

  • 11 Answers

SOURCE: how to turn on hot tub

Check at the plug in if it has a normal plug like in your home first. Should be a set of buttons there, called a GFI. One is test, and the other reset.Push reset to see if spa comes on. Most spas dont have an actual on button. Check breaker box for popped breaker also, maybe tub is having problems, and needs a service call. Also larger tubs ussually jave a gfi or fuse box outside, close to tub. Kirk

Posted on Feb 17, 2009

Ad

Anonymous

  • 1 Answer

SOURCE: Wiring diagram for Ramsond 18000 BTU Ductless

See link below for detailed wiring. I found it very helpful



http://www.ramsond.com/minisplit/wiring/detailedwire5170.pdf

Posted on Oct 02, 2009

Kieran Ruppert

  • 990 Answers

SOURCE: Heeeelp! How to hook up hoses on Sundance spa

There is a skimmer in the side of your tub( the part that skimms water off the top ) and what is called a main drain or a better tearm is deep suction that pulls water from the bottom of the tub and helps collect heavy dirt from in the tub these two lines ( three if there is more than one main drain) These will all come together and then hook to the front of the pump. If your filter is under the skimmer basket the top of the pump will go to the heater and then back to the spa. If your filter in not under the skimmre basket then it will come after the pump then on to the heater. So in answer to your second question, the front of the pump draws the water in and the top pushes the water out. But make sure that your heater is last in line so it only deals with clean water and it will not run on the suction side of the pump as it need water pressure in it to start and contious flow to keep it from over heating. Hope this helps.

Posted on Oct 03, 2009

Anonymous

  • 1 Answer

SOURCE: Hot tub maintenance

DRAINING AND REFILLING BALBOA HOT TUB

Posted on Oct 24, 2009

Dale Cobb

  • 366 Answers

SOURCE: How do you replace a flow switch in a spa, or hot tub

turn off the power to the spa. remove the cabinet under the topside remote to expose the equipment compartment. You should see the flow switch, it's usually a threaded 3/4" plug with a single grey wire coming out of it. Most of them are threaded into a tee or a special transparent fitting. If the water level in the spa is above the flow switch, you may have to drain the spa down unless you're very fast about getting the new switch in. Unthread the old switch and thread the new one in. Follow the wire on the old one to the spa pack. You'll have to remove the screws on the cover to expose the circuit board. Follow that wire into the spa pack to see where on the circuit board that it is plugged in. It may be good to run the new wire to have in place as soon as you unplug the old one you can install the new one with no question as to where it plugs in.

Reinstall the cover on the spa-pack and turn the main power back on. Make sure that the arrows on the new flow switch are facing the correct direction (direction of flow). Once you have the spa on and it starts back up, run everything to check for leaks and proper operation. If the flow switch was the only problem, all your faults should be cleared and you should be in good shape. If there are no leaks, you can reinstall the cabinet panel.

The new switch should already have teflon tape on the threads, if not, use teflon tape, apply the tape in the direction as if you were threading a nut onto the threads. You only need a few wraps of teflon tape, too much can crack the fitting you threat the new flow switch in to.

Posted on Nov 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

I need to find a service man in the Seattle area to get my tub working. It has power but won't come on.


then look in a phone book for a plumber . I am sure there are more than 1

Feb 11, 2016 | Home

1 Answer

Why won't the spa turn on?


The best way to detect where your problem may be is by testing each unit associated with your hot tub. Start by turning off the main power, now unplug all the accessories on your power pak
  • pumps
  • blowers
  • lights
  • ozonators
  • radio
something is tripping your power pak and this is the quickest way to find out. Turn the main power back on. Plug in each accessory pausing between, when the pak trips you know you have found your issue. It could be as easy as a fuse or a ceased pump.

Once you find out what needs to be repaired you may want to call out a hot tub service professional to repair the unit. Hot Tub Power Pak Repair

Jul 27, 2015 | Pool & Spa

3 Answers

Morgan hot tub


if no drain at bottom usually with hose connection on it use a sump pump or syphon make sure power is off until fully refilled

Jun 30, 2014 | Pool & Spa

2 Answers

My hot tub doesn't heat up all the way even though it says it's ready


If a floating thermometer is more than 3-4 Degrees F off what the control panel display temperature then the temperature sensor has likely failed.

Jul 17, 2012 | Pool & Spa

3 Answers

Spa thermal overheating


Turn off all power to the hot tub as soon as you realize it is overheating. The spa should have an automatic shut off when the water temperature reaches about 112 degrees fahrenheit. Call your hot tub dealer or manufacturer for service options. There are a variety of conditions that could lead to the overheating of your hot tub, but may differ in various hot tub models and brands. Check the water level of the hot tub. Low water levels could be the culprit for the over heating, so you may just need to add more water to the hot tub.
Check the shut-off valves in the hot tub. If they are closed while the hot tub heater is on, it could cause the water to reach unsafe temperatures.
Clean the hot tub filter. A dirty filter could be blocking the flow of water, causing the water to sit in the hot tub and overheat.
Turn the power back on after finding the problem and talking to the hot tub dealer. The hot tub will probably not start back up until the water reaches a safe temperature

Jan 06, 2012 | Endless Summer Pool & Spa

1 Answer

One of the hot tub motors turns on and off when powered up


It would commonly be the spa pack. A technician would be needed to diagnose this issue.

Dec 22, 2009 | Dream Maker Spas Dream Maker Ez Spa Hot...

5 Answers

Hot tub has power but nothing else works


MY control panel was replaced ,it cycles but, no lights ,no jets,no heat works..What's the problem .

Oct 01, 2009 | Dream Maker Spas Dream Maker Ez Spa Hot...

1 Answer

How to turn on hot tub


Hot tubs do not have an "on" button. They are preset to heat up to 100 as soon as the breaker is turned on.

May 31, 2009 | Qca Spas Paradise Hot Tub

2 Answers

Hot tub wont stay hot


Contact Maryland Hot Tub Repair - Pool and Spa Service and set up a Diagnostic service call. Here is there contact info: Maryland Hot Tub Repair - Maryland Pool Service - Maryland Spa Repair Pool Parts - Spa Parts - Hot Tub , Pool and Spa Repair - Pool Opening - Pool Closing - Pool Service 410-304-2463 http://www.maryland-hottub-pool-spa-repa... or see them on http://marylandhottubrepair.blogspot.com...

May 20, 2009 | Jacuzzi DX50-959 Elara 7242 Salon Spa...

1 Answer

New set up


Do you have power at outlet? If yes, check for 120v at control pack (follow cord to terminal board ). If no power at terminals and gfci on cord won't reset then power cord is defective. Replace

Apr 13, 2009 | Qca Spas Dream Series Dream Master Hot Tub...

Not finding what you are looking for?
Pool & Spa Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pool & Spa Experts

Bill Jordan

Level 2 Expert

375 Answers

john h

Level 3 Expert

22486 Answers

David Spradling
David Spradling

Level 3 Expert

10790 Answers

Are you a Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...