Question about Tools & Hardware - Others

Open Question

50mm nails for a parkside staple nail gun - Tools & Hardware - Others

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 195 Answers

SOURCE: staple,nail gun, how do i install the nail properly

SHOULD BE A SPRING LOADED TAB LOCATED USUALLY AT THE REAR OF THE GUN. PRESS IN THEN DOWN AND SOULD POP OUT SO YOU CAN LOAD.

PLEASE RATE
THANKS

Posted on Mar 20, 2009

Ad

Anonymous

  • 288 Answers

SOURCE: How do you load nails into a stanley tre550 nail

there should be a button on the bottom rear of the gun, when you press it, it should release a bar that you pull back. the nails go in the dirction you nail them. sometimes the clips are too big for the guns and you have to break about an inch off of them

Posted on Dec 06, 2009

blueextc3221

blueextc3221

  • 15935 Answers

SOURCE: how do you load nails?

The staples are NOT loaded on top of the pull out shaft; they are inserted directly into the slot that opens when you pull the shaft out. If the nose of the tool is not placed firmly against a surface, it will not fire.

CLICK HERE
and click the PDF icon on the right of the model # to start the download.

Here is a step by step:
Unplug the tool.
Squeeze the end of the shaft at the rear bottom of the tool and pull out the shaft.
Flip the tool over on it’s back.
Insert the staples, (points up) and then slide the shaft back in.
Plug it in, press the on button (under the the power cord in the back). Press the nose squarely against the material and press the trigger
.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Posted on Mar 06, 2010

CaptAdams35

Christopher

  • 28 Answers

SOURCE: how do you load nails in stanley tr250 staple and

The magazine on the TR250 has a recess on one side as well as a relief at the top where the driver pushes them through the opening. Load the brads/nails on that side of the magazine and it should operate properly. AS A REMINDER: ALWAYS REMOVE NAILS/STAPLES/BRADS WHEN NOT IN USE AS THIS WILL WEAKEN THE SPRING AND CAUSE FEED PROBLEMS IN THE FUTURE.

Posted on Mar 09, 2010

thesnooper

  • 342 Answers

SOURCE: Need help loading staples in my Stanley electric staple/nail gun

there should be a button / lever at the rear press it and it should open so as to insert the staples

Posted on Apr 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

Power nail/staple gun


The worst pneumatic nail/staple gun is still better than the best electric nail/staple gun.

on Oct 26, 2013 | Chicago Pneumatic Air Tools & Compressors

1 Answer

My Pro 8000 stapler has about 20 staples jamed I need to how to unjam thew booklet does not show this


Clearing the Nail and
Staple Chamber
If, while using your Cobra

staple
and nail gun, it becomes necessary to
clear a jam from the staple chamber or
track, follow these instructions:

With the bottom of the gun
facing away from your face and
body, open the staple chamber by
squeezing and pulling the plastic
track release straight down away
from the base of the gun and
sliding the track back.(Fig 1)
(Note: the jammed staple or nail
may cause the track to be harder
to slide out than usual. Once the
staple or nail has been cleared,
the track will resume its normal,
free operation) Loose staples or
nails will be expelled from the
chamber.

Clear any remaining staples or
nails from the track and chamber
area.

Reload the Cobra staple and nail
gun and continue using.

May 17, 2017 | Staples Tools & Hardware - Others

2 Answers

How do I load the stapler?


No you don't. We answer most things here.

If the stapler is like any of these

http://www.amazon.com/s?ie=UTF8&page=1&rh=i%3Aaps%2Ck%3Abostitch%20staple%20gun

You push the back in slightly to unlatch it and then drop it down a bit and the staple pusher comes out completely.

Jan 28, 2016 | Heavy Duty Stanley Bostich Heavy-duty...

1 Answer

How do I load nails into the 5700


Here is the link but I copied the instructions here too


http://ec1.images-amazon.com/media/i3d/01/A/man-migrate/MANUAL000035709.pdf



Loading Staples or Nails

Make sure there are no staples or nails jammed from previous usage by checking the handle operation.

CAUTION: IF A STAPLE OR NAIL IS JAMMED, POINT THE GUN AWAY FROM

YOURSELF AND OTHERS BEFORE OPENING THE TRACK AS THE JAMMED

STAPLE OR NAIL MAY BE FIRED OUT UPON OPENING

i) Point the bottom of the gun away from you and turn gun sideways.

ii) Turn gun up, grip track release buttons and push away to release, then slide the track out, as shown (fig. 1).

iii) Insert a strip of staples in the chamber with the legs pointing up (fig.1a). If nails are required, turn gun upside

down and tilt the gun away from yourself and load on the right hand side (as indicated on graphics at the

staple and nail exit) with point facing upwards (fig.1b) THE GUN MAY JAM IF NAILS ARE INSERTED IN THE

WRONG SIDE.
*Arrow

iv) Slide staple or nail track back into closed position - a click indicates that it is locked in position.
Your staple and nail gun is now ready for use.



May 20, 2011 | Garden

1 Answer

Need help loading staples in my Stanley electric staple/nail gun


there should be a button / lever at the rear press it and it should open so as to insert the staples

Apr 05, 2010 | Stanley Staple/Nail Gun Elec

1 Answer

Putting the nails inside the gun


Here is the manual http://www.arrowfastener.com/upload/manuals/79055020257_manual.pdf
Eric

Jan 24, 2010 | Staples Arrow T2025 Staple Gun For Flat &...

1 Answer

How do you load nails into a stanley tre550 nail staple gun?


there should be a button on the bottom rear of the gun, when you press it, it should release a bar that you pull back. the nails go in the dirction you nail them. sometimes the clips are too big for the guns and you have to break about an inch off of them

Dec 06, 2009 | Stanley Tools TRE550 Electric Staple/Brad...

Not finding what you are looking for?
Tools & Hardware - Others Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Tools & Hardware - Others Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Brad Brown

Level 3 Expert

18110 Answers

john h

Level 3 Expert

22486 Answers

Are you a Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...