Question about Cuisinart DLC-8S Pro Custom Food Processor

Open Question

My cuisinart food processor DLC-8s won't turn on

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
ThaMp3Doctor

ThaMp3Doctor

  • 8597 Answers

SOURCE: How to put new shaft on cuisinart food processor model DLC-7E

Initial disclaimer: I am not recommending this course of action - my recommendation is to buy a new food processor. These units weren't designed for DIY repair, so this is going to be a difficult task. The final product probably isn't even going to be pretty. You are well out-of-warranty, or I wouldn't even consider posting this. First, make sure you have a DLC-7E shaft - the only way to get one at this point would be to buy a DLC-7E base from eBay or an after-market seller, as all of these were manufactured well over 20 years ago. I don't currently see any eBay listings for one, but they do crop up from time-to-time. Make sure the DLC-7E you are repairing and the old one from which you are wrenching the old shaft are unplugged and have been unplugged for an hour or longer just to be on the safe side. Unscrew the four screws on the bottom of the base on both units. If the bottom base does not come off after this, carefully pry out the four feet and unscrew any hidden screws that might be hidden underneath the feet (Careful - original feet cannot be ordered by normal means, and damage will only add to your total repair cost). Take note of the guts on the inside of both food processor bases - if you have to unscrew the motor body (4 screws that sit just underneath the top of the base), take note of everything that you are taking out so that you can put it back in its proper place when done. Wear leather gloves for safety. Please be aware that even an unplugged unit still has the potential to send several volts of electricity through your body - this is a potentially hazardous task. Once the motor body has been unscrewed and removed slightly (don't disconnect any wires or cables - just get the motor body out of your way), you will notice the old shaft that you intend on replacing. Look for any damage to the gears/bearing that surround this shaft. Try dabbing a small amount of USP-grade mineral oil on any bearings - clear away any dust or debris that may be obstructing the shaft from turning. Don't overapply the oil, or the wetness will seep into other electronic components in the motor and cause them to fail. Put your food processor back together, turn it on, and press the button/buttons on top of the base of the food processor with a pen with the food processor plugged in. If the shaft still won't turn, you definitely need to replace the old shaft (you can disregard some of these previous steps if your problem is that the spindle on the old shaft is worn).
Remove the screws and disassemble the processor base as described above. Since there is a layer of paint/coating surrounding the old motor shaft, removing the old shaft may cause paint flecking. Take the shaft from the one food processor base and insert it in the food processor you are trying to repair. Strip away any excess paint/coating from the new shaft. Make sure no paint flakes remain in the body of the food processor, or they will later cause more serious problems that will permanently damage your food processor - potential fire hazard as well. You will probably notice that the new shaft does not look as pretty as your original shaft, since the paint/coating will almost invariably get damaged in this process. Reassemble the base of the food processor, making sure no wires, etc. were knocked out of place in the process. This paint flecking will add to the cost of the repair - you may need to buy appliance body paint that dries to almost a rubbery consistency to make the final project look nice. All of the materials listed above could cost you $40 or more.

Like I said, I don't reccomend this course of action, but there's your answer.

Posted on Mar 17, 2009

Ad

Anonymous

  • 2 Answers

SOURCE: need manual for food processor

Found it at:

http://safemanuals.com/user-guide-instructions-owner-manual/CUISINART/DLC-10S-_E

Posted on Sep 15, 2009

techfrog

  • 1 Answer

SOURCE: I have a Cuisinart DLC-8S TX Pro Custom 11 Cups

If you already have a lot of attachments for this model, I would purchase a used motor unit. I got a complete setup at a yard sale minus the work bowl cover for $3 as a spare, and often see them at thrift stores priced quite inexpensively. You could also check ebay. Motor units routinely go for less than $25 including shipping. I'm pretty sure most dcl-8 series motors will work with you bowl and attachments. I like the quality of the older units better than the newer ones. And if you watch ebay closely, you can pick up a lot of pieces really cheaply. Good Luck,

Marc

Posted on Nov 01, 2010

kendbin

kendbin

  • 1 Answer

SOURCE: replace the spindle on Cuisinart DLC-7 Food Processor

You need to pull the old one off, probably with vise grips and a lot of effort, and then order a new one. The new one is a tiny bit larger, so you'll probably need to order new blades, too. The new one slips right on, so there's no issue that would be the reverse of removing the old one. I read somewhere else that you have to pound hard to get the new one on, but that guy must have been speaking about the older model spindles. I was perplexed that the new one slipped right on so I pounded it to be sure and ended up breaking the tip of the new spindle and cracking the housing of the whole processor.

Posted on Jan 17, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Cuisinart Processor workbowl lid fitting


Cuisinart DCL-7 replacement work bowl lid is cuisinart dlc-017bgtx work bowl lid fitting with large feed tube.


10_13_2012_7_45_59_am.jpg

Jun 05, 2009 | Cuisinart DLC-8S Pro Custom Food Processor

1 Answer

Need the instruction manual for a cuisinart dlc-8 plus.


http://www.cuisinart.com/share/pdf/manuals/dlc-8s.pdf

Cuisinart.com also has the How-To video and a product demo if either of those things help. Just go to the home page and search under Entire Site for DLC-8S.

May 28, 2009 | Cuisinart DLC-8S Pro Custom Food Processor

1 Answer

Put in nuts and turned to mush


It is extremely difficult to chop walnuts in a food processor, because they turn to powder within a few seconds. I have chopped them using both a Cuisinart food processor and a Moulinex La Machine. The difficulty arises because even after you have released the on or chop button, the blade continues to spin for a second or two. The Cuisinart DLC-8S is not particularly well-suited for chopping nuts, because the blade is not reversible - there are many Cuisinarts that do have reversible blades - a particularly good one is the Cuisinart DLC-2A, which has both a reversible blade and a Chop function (retails for about $29.99 to 39.99 nowadays).

The only way to have any success whatsoever with the DLC-8S is to press the pulse button and release immediately - only use a small amount of walntus - and then dump the bowl and add a few more at a time.

Apr 04, 2009 | Cuisinart DLC-8S Pro Custom Food Processor

1 Answer

Cuisinart DLC- 8M


Those older Cuisinart food processors have motors that generally last forever. But a replacement bowl can cost $118.00 or more. The newer processors like the DLC-8S do have a 3-year general warranty and a 5-year motor warranty. The new DLC-2011, 2007, 2014 series etc. have 10-year motor warranties. I like the collect the oldies, but the new ones have few problems even though they are made in China. If an old processor's plastic breaks, you have to buy a completely new bowl set - if a new processor's plastic breaks, then you can buy a single component piece to solve the problem. Hope this helps.

-Tha Mp3 Doctor

Sep 19, 2008 | Cuisinart DLC-8S Pro Custom Food Processor

1 Answer

Lid won't lock


I've lost my instruction manuel for my Cuisinart Custom 11 ( DLC-8S) food processor and was hoping
you have one on file I can copy. Thank You in advance
Mickey Riley

Sep 02, 2008 | Cuisinart DLC-8S Pro Custom Food Processor

Not finding what you are looking for?
Cuisinart DLC-8S Pro Custom Food Processor Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cuisinart Food Processors Experts

ThaMp3Doctor
ThaMp3Doctor

Level 3 Expert

8597 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Bruce Showalter

Level 2 Expert

133 Answers

Are you a Cuisinart Food Processor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...