Question about Honeywell Heating & Cooling

1 Answer

Is there pc available video showing how to install wires into Honeywell fan limit control L4064B2210

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Honeywell Master
  • 54,932 Answers

Check YouTube

Posted on Dec 10, 2019

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 10 Answers

SOURCE: I have a Rheem model RRGG 05N37 JKR Serial # AYA4785

Typically any fan limit switch will work as long as it is the same length as the old one and is in temperature range as well as covering the hole that the old ond came out of. it the screw holes do not line up, besure to put a screw into the exposed holes to prevent heated air from leaving the cabinet

Posted on Oct 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a bad fan/limit control Honeywell L4064A 2188.What would sbe a suitable replacement part number?


take original honeywell model # go to honeywell site and look for original part # and it will give you cross reference #s

Nov 05, 2013 | Honeywell L4064B2236 Fan/Limit Control...

1 Answer

Blower fan running constant after new fan and limit switch installed.more info.Honeywell-tradeline.L4064B 2210, combination fan and limit control, adjustable fan differential with manual fan switch, flush...


Here's my best shot.
Check the temperature settings for the fan switch.
The low OFF setting should be about 100 degrees.
The ON setting should be around 150 degrees and this is the setting that "makes" the ON contacts.
The HIGH LIMIT setting should be about 180 degrees.
If these are set, can you use a meter to see if the FAN ON contacts are closed?
Lastly, it appears that one hot line should go to one side of the blower and the other hot line should go to the bottom FAN terminal with the other side of the blower being fed by wiring from the top FAN terminal.
Good Luck. Gary

Feb 21, 2011 | Honeywell Heating & Cooling

1 Answer

Need wiring diagram for honeywell limit control switch


http://www.inspectapedia.com/heat/Fan_Limit_Switch_Installation.htm#Wiring Go here, it is a super site for just about everything home related.

Dec 24, 2010 | Honeywell L4064B2236 Fan/Limit Control...

1 Answer

How does a honeywell L4064b2236 work? It is set up on a Gas hot air furnace with the jumper removed, Three wire connection, black to common white to fan and red to limit. The furnace has a tranformer on...


If the jumper has been removed, then the control is working in the low voltage circuit. Black should be 120v in, White the 120 going out to the fan, and the red or limit wire is (should be) in the low voltage control circuit. Have you looked at the wiring diagram for the F and L Control? If not I will provide a link for you. https://customer.honeywell.com/techlit/pdf/69-0000s/69-0117.pdf

Hope this helps

Nov 16, 2010 | Honeywell L4064B2236 Fan/Limit Control...

1 Answer

Honeywell MagicStat 3200 Fan continues to run--I flipped furnace breaker off for an hour, set stat to off, & flipped breaker back on. fan still runs. Fan control is on Auto.


Hello,If just installed the thermostat check that the wires are not touching anywhere.If not the case you have a open(tripped) HIGH LIMIT at the furnace and the blower will continue to run untill it is reset.

Oct 30, 2010 | Honeywell Programmable Thermostat Heater

1 Answer

How to wire it


Hmm this is tricky it depends what kind of furnace you have etc....need more info but basically you supply 120V to the common connection(with the jumper) and from there you would run a wire L1 to the furnace motor from "Load" on the fan side....and the wire L1 from the "Limit" side will power the furnace transformer../..the Limit ios very important and must be wired correctly...I suggest you have an exspert install it
a58a277.jpg
d87ddb6.jpg

Nov 01, 2009 | Honeywell L4064B2236 Fan/Limit Control...

1 Answer

I have a Rheem model RRGG 05N37 JKR Serial # AYA4785 manufactured in 1993. I have to replace the fan limit switch. Is the Honeywell L4064B2210 Fan/Limit Control Switch the correct one?


Typically any fan limit switch will work as long as it is the same length as the old one and is in temperature range as well as covering the hole that the old ond came out of. it the screw holes do not line up, besure to put a screw into the exposed holes to prevent heated air from leaving the cabinet

Oct 21, 2009 | Heating & Cooling

2 Answers

When I set tstat to call for a/c, compressor outside comes on. Blower on furnace does not. When I manually rotate fan limit switch on furnace wall, blower comes on, blows cold air, and then goes off when...


blower relay bad or no call from stat on green wire to run fan jump red on stat to green if fan comes on stat bad if no look for fan relay turning the well switch bypasses the relay hope this helps

May 24, 2009 | Heating & Cooling

1 Answer

Blower fan runs to long


ther might be dip swiches on the circuit board you might have to change

Dec 17, 2008 | Honeywell Power Humidifier: Furnace...

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honeywell Heating & Cooling Experts

Bill Long

Level 3 Expert

606 Answers

Paul Carew

Level 3 Expert

3480 Answers

Cindy Wells

Level 3 Expert

6048 Answers

Are you a Honeywell Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...