Question about Water Water Heaters

1 Answer

How do i reset my boss therm

No hot water or heating

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Some heaters are there's and indicator of reset button on the unit..and some are located inside the unit can be push by using screwdriver.

Posted on Dec 05, 2019

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My bocsh 830es water heater will be running normal then will kick into a A3 mode no more hot water


Check for a green wire near the top right of your machine. It would loop back to itself with a little black heat shrink on it. This should be far away from the heat exchanger. if its near it, I would recommend pulling it out of the wire clips, and relocating it to behind the control unit on the right side of the machine. Keep it away from heat....its a resistor, and will pop random A3 codes if the heat increases its resistance. Reset your code and you'll be good to go.

Jan 01, 2014 | Bosch Therm 830 ES NG Internal Tankless...

1 Answer

I'm getting an er3 reading on my water heater tank , what does that mean


It tells you that your water heater called for heat for more than an hr and never got hot enough to meet the demand.
CAUSES

-bad sensors
-no hot water from boiler
-bad thermal transfer
-low delta T across water heater

Apr 21, 2011 | Amtrol ST-120V-C THERM-X-TROL ASME...

1 Answer

Armitrol boiler mate hot water maker has code er3 and we have not hot water. can u tell us what that code means?


It tells you that your water heater called for heat for more than an hr and never got hot enough to meet the demand. multiple scenarios can cause this
CAUSES

-bad sensors
-no hot water from boiler
-bad thermal transfer
-low delta T across water heater

Dec 02, 2010 | Amtrol ST-120V-C THERM-X-TROL ASME...

1 Answer

I have a ER3 message. How can I fix this


It tells you that your water heater called for heat for more than an hr and never got hot enough to meet the demand.
CAUSES
-bad sensors
-no hot water from boiler
-bad thermal transfer
-low delta T across water heater

Mar 15, 2010 | Amtrol ST-120V-C THERM-X-TROL ASME...

1 Answer

ER3 no hot water


Er3 means that the water is being heated for more than 1 hour without reaching the set temperature.
Need new aquastat.

Sep 28, 2009 | Amtrol ST-120V-C THERM-X-TROL ASME...

1 Answer

Caluclation


This requires a little math....

BTU - amount of heat it takes to raise one pound of water 1 degree F.

I gallon of water = about 8.54 pounds

91 gallons of water = about 777 pounds = 777 pounds x 70 degree rise = 54,390 BTU.

1 Therm (what the gas company measuers in) is 100,000 btus

1 therm costs about $.45 (45 cents) depending on where you are

54,390/100,000 x $.45 = about $.25 per hour

This cost can vary somewhat depending on the inlet water temperature, gas cost, and the efficiency of the hot water heater

Apr 08, 2009 | Water Heaters

1 Answer

Water not getting hot


You seem to have a burned out heater elemt. Most water heaters have 2 e.ements. If the upper one bruns out, it will not heat at all. If you have a cheap heater built by State, you probably have a bad lower thermostat. It will over heat and trip the protection device. If you reset the red button on the upper thermostat and it gets too hot (check in about 2 hours) then replace the lower therm. You could still have a burned out upper element.

Mar 31, 2009 | Water Heaters

Not finding what you are looking for?
Water Heaters Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Water Heaters Experts

vince

Level 3 Expert

1234 Answers

80stech

Level 2 Expert

120 Answers

Kenneth Walker

Level 2 Expert

292 Answers

Are you a Water Heater Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...