Question about Computers & Internet

2 Answers

E61 error - Computers & Internet

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 45 Answers

Most often, this error occurs when your boot sequence is misconfigured in your BIOS, or your boot device cannot be read correctly

steps:
1.Boot your computer and Enter your bios setup Check that the boot sequence is not configured for network boot. Make sure that your hard disk is listed in the boot sequence. Try making your hard disk the first device in your boot order using the keys shown at the bottom of your screen.
2.If your hard disk is not listed as an option in your boot sequence, this may indicate that your hard drive has failed or the connection has come loose. If it is a desktop computer, you can power it down, open the case and make sure that the connections to your hard drive are connected firmly and properly. In the image below, the power and data connections of a typical SATA hard drive are shown.

It is also possible the SATA cable is defective and the computer is not able to detect the hard drive due to a bad SATA cable. If the cables are firmly connected to the hard drive and to the motherboard, and the error still occurs, try replacing the SATA cable.
If your computer is a laptop, you may not be able to open it and check the connection. In this case, we recommend having a trained repair professional perform this task for you.
3.You may also want to check the Jumpers on your hard drive to make sure they are configured correctly. Again, this is only recommended if it is a desktop computer, not a laptop. Consult your hard disk manual for more information about correct jumper settings.
4.In your BIOS setup, look for diagnostics options to self-test your primary hard disk drive. Consult your computer or motherboard manual for details.

Posted on Dec 01, 2019

Ad

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

  1. Turn off the monitor. If the screen is dark it will be easier to see the dirty and oily areas.
  2. Use a dry, soft cloth -- the kind you would use to clean your eyeglasses -- and very gently wipe the screen. ...
  3. Make a solution of equal parts water and vinegar (or water with a tiny amount of dish soap).

Posted on Dec 01, 2019

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced heating element now I get error E61, I ohmed out the thermostat on top of heating element seem to be ok


Hello Louie, I appreciate your inquiry!
Based off the information you have provided your Frigidaire dryer is displaying an error code of "E61" after you have replaced the element. An "E61" error code means that there could be an issue with your heater relay or main control board. You may need to seek additional assistance from a professional technician for proper diagnosis and repair. This will help you avoid any unnecessary part purchases. I hope this information is helpful to you. -Matt

Mar 28, 2016 | Frigidaire FASE7073LW Affinity 7.0 cu ft...

1 Answer

Replaced circuit board and i have heat but still shows e61 code


Hello friend, thanks for your post!

Based off what you have described your Frigidaire dryer is displaying an error code of E61. I understand that you have replaced the circuit board and you are still receiving the error code. An E61 means that your heater relay as had a failure which could be a potential problem with your heater relay or a wiring harness. You may need to seek professional assistance with proper troubleshooting this will help you to avoid any further unnecessary part purchases. If you need help locating a local technician you can visit your manufacturer's website for a list of available technicians. -Matt

Aug 05, 2015 | Frigidaire Dryers

1 Answer

I have a Frigidaire Affinity electric dryer model number FASE7021NW0. It suddenly began giving error code E61. I called frigidaire. they said it was likely a shorted wire and put me in contact with an


I appreciate your post, Doug Anderson! From the information you have provided your Frigidaire dryer is displaying an error code of "E61". "E61" stands for heater relay failure which could be a problem with wiring, heater relay, or main control board. I would recommend performing a reset on your dryer and you can do that by disconnecting the power cord for ten minutes. This should help clear out any potential false error codes. Hope this information is helpful. -Matt

Dec 20, 2014 | Frigidaire Dryers

1 Answer

What is PXE-E61?


Go to:
http://askville.amazon.com/resolve-PXE-E61-error-message-crash/AnswerViewer.do?requestId=1248801
This is a thread dedicated to the "PXE-E61" problem.
I hope you find your answer there.

Aug 19, 2014 | Computers & Internet

1 Answer

Pxe E61 Media Test Failure Check Cable


my server ph prolite doesn't start gives an error essage "PXE-E61: Media test failure, check cable" the reboots after 5 seconds

Apr 22, 2012 | HP ProLiant DL180 G5 Server

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Ekse

Level 3 Expert

13434 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

Brad Brown

Level 3 Expert

18139 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...