Question about Maytag Washing Machines

2 Answers

Hi i have a Maytag centennial washing machine that does not spin when it get to the spin cycle i was wondering what the cause can be

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Maytag Master
  • 10,679 Answers

Check belt under unit if ok see if motor spins if ok check under agitator and replace cog spline under agitator

Posted on Dec 26, 2019

Ad

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 943 Answers

Needs further investigation. It seems to be your control board has an issue.

Posted on Dec 05, 2019

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Coldcut

Karl Whisenand

  • 1554 Answers

SOURCE: loud squeal during wash and spin cycles, maytag atlantis washer

The belt is slipping and needs replaced.

Posted on Jan 26, 2008

Anonymous

  • 67 Answers

SOURCE: loud squeal during wash and spin cycles, maytag atlantis washer

Squealing normal occurs due to belt slippage. I would check your belts (look for cracks. Check the belt tension as well, most washers have an adjustment, normally on the motor that allows you to increase the tension of the belt.

If part of a belt gets torn and it is long enough, it will hit any part of the washing machine within range and make a clicking noise at every revolution of the motor.

I am pretty sure you need new belts. You should be able to remove a few screws and open the back cover. Between the pulleys there is a tensioner...loosen that so you can remove the belt easily. replace it with a new belt and adjust the tension.

hope this helps

Posted on Feb 23, 2008

David Coomer

  • 1073 Answers

SOURCE: Maytag Washing Machine Stops after wash cycle...

sounds as if you have abad contact in the timer
advance the timer to a different spin cycle and see if it spins
then bo back to where it stops
if it will spin in the other spin cycles but not where it stops the the timer will need to be changed

Posted on Apr 21, 2008

duby1990

Justin Duby

  • 370 Answers

SOURCE: My MayTag performa oversized capacity washer wont spin

Usually this is caused by the pump being cloged or broken. Remove the pump and clean the pump out. Make sure it spins freely by hand.

Posted on Nov 21, 2008

richroth

Richard Roth

  • 9472 Answers

SOURCE: Washer immediately goes into wash cycle when

The water-level switch regulates your washer's fill volume. This switch is usually a diaphragm device with a small, clear tube attached between the switch and the bottom of the washer's outer tub. As the water level in the tub increases, the pressure on the air in the tube increases. When the pressure reaches a certain level, it activates the switch, shuts off the water, and signals the timer to begin the agitate cycle. If the switch is defective, it may prematurely signal the water to shut off. If so, you probably need to replace the water-level switch.

Posted on Jan 26, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Wash cycle will agitate 3 spins then nothing for a few minutes then 3 more and nothing again and repeat over and over


you may want to put it through a diagnostics cycle and check for error codes... Maytag Centennial Washer Repair Guide
The tub sensor can cause the washer to act strangely like that. Also there are two mechanical styles of washer branded Maytag Centennial. The model number would help to know we are talking about the one I think we are talking about.
Hope that helps!

May 27, 2015 | Maytag Centennial 3.2 cu. ft. SuperSize...

1 Answer

Spin cycle not working properly. A little water (1 inch) is left and clothes are heavy with water. I tried the spin cycle repeatedly - water still at bottom of tub.


Hi,

Problems with a washing machine not spinning or not draining are often interrelated..

If you are having a problem with your top load washer then check out thistip...

Washing Machine does not Pump or Spin


If you are having problems with your front load washing machine then checkoutthis tip...

Front Load Washing machine not draining and or not spinning


heatman101


] ]\ [

Aug 10, 2011 | Maytag Centennial MTW5800TW Top Load...

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

jimorris77

Level 3 Expert

411 Answers

Sheldon Dedek

Level 3 Expert

909 Answers

Bill Long

Level 3 Expert

606 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...