Question about Kenmore Washing Machines

Open Question

Kenmore vacuum Model 116.22513202. There's an electric plug by the latch that is difficult to connect and close the lid.

Posted by on

Ad

5 Suggested Answers

Anonymous

  • 639 Answers

SOURCE: Kenmore front end loader HE 3t Model 110.45972400

Peace Friend,
ngfam1 At your service!


It is not an easy matter if you have never done this before!

How old is the washer?

If the appliance is 10 years old or more you it may not be advisable to put good money into bad!
New appliances are so much more efficient today that they can save you a lot of money in energy!!!!
Water,Electric and detergent! And put money back in your pocket!
The new appliance will pay for itself in only a few years!

If not only a trained laundry tech can make the electronic diagnoses.
Like we used to be able to fix my own cars, but not today they need diagnostic equipment!
Below I referred you to a great service nation wide!

If none of these tasks remedy the problem then here is a good company that's found nation wide.
A&E Factory Service
A&E has schedulers available to take appointments 24/7
And they do warranty work too, for most manufactures!
1(800) 905-9505

You will be fine
Bless You ngafm1
PLEASE GIVE ME A GOOD RATING HERE AT FIXYA.COM BEFORE YOU SIGN OFF!!!!!!!!!!!!!!!!!

Posted on Sep 02, 2008

Ad

raymundo_mnd

  • 10 Answers

SOURCE: trunk lid

do you have the striker plate missing? if not i had spryed some WD-40 on my and it worked. if you have striker plate missing try to put some tape,(electrical tape). you can find these parts at cjponypats.com, part #TLSP5 they are about $30 or less

Posted on Oct 12, 2008

Ad

Anonymous

  • 132 Answers

SOURCE: my 2001 volvo s60 trunk lid wont close

TRY PUTTING THE KEY IN AND TURNING IT AS IF YOU WERE OPENING THEN PULL OUT KEY AND TRY CLOSING THEN TRY AND SEE WHAT HAPPENS

Posted on Nov 15, 2008

John Hall

  • 1218 Answers

SOURCE: kenmore washer lid switch problem

Good day,
Common problem, Change the switch, and make sure if it is the model with a plunger for the switch mounted on the lid, that that be replaced as well.

Thank you for using FixYa

Posted on Dec 29, 2009

Daniel S

Daniel Scott

  • 4323 Answers

SOURCE: Kenmore Model 116 28014700 intuition

Hi

To remove the broken part from the latch use a small screwdriver to release the tabs on the latch on the connector. When latches are released the latch assembly and the plate will slide out of the connector. When the plate is removed the adapter and hose will slide off the connector. Release the tabs that hold the hose to the adapter and put the hose on the new adapter.
You need to position the terminal plate inside the adapter before sliding the adapter and hose on the new connector. The latch and terminal plate have to slide under the small guides on the connector. Its reverse of removal. Please check the pictures in the below link, it may help---

Link 1

Link 2

Link 3

Hope this helps... Please post back if you need more information.
Daniel

Posted on Jan 06, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore power mate works intermittently ever since I took it apart and cleaned the sensor. It's like something is now loose with the power connection but I can't figure it out.


Electrical issues can be difficult to diagnose. You have to inspect closely and wiggle wires and connections to determine where the problem is.

Sep 08, 2017 | Kenmore Vacuums

2 Answers

Beater bar turning on and off. Why doesn't the vacuum?


Try wiggling the wire and where the hose swivels to attempt to determine where it may be shorting out. It could be the wire or the plugs where the wires connect if your model has them. Inspect these areas closely to find your short.

Apr 08, 2016 | Kenmore Vacuums

1 Answer

Kenmore model 70 washer will not empty tub with lid closed.


This is a broken lid switch . You can replace the lid switch or if you need to get it working quickly you can bi pass the switch by unplugging the washer, removing the 2 lid latch screws, pulling out the switch cutting the 2 wires and twist them together with a wire nut.
This is assuming you do not have the self locking lid.But I don't think your model has that function.

May 14, 2011 | Kenmore Washing Machines

1 Answer

Kenmore elite 110.26922503 washing machine. The top lid closure switch doesn't always close when the lid is closed.. is it difficult to get to do replace or clean and adjust?


First, see the Sears parts site for your washer:

http://www.searspartsdirect.com/partsdirect/part-model/Kenmore-elite-Parts/Washer-Parts/Model-11026922503/0583/0153200?pathTaken=

Look at the section on the cabinet and console. You should see the lid switch:\

All you have to do is release the console and pull the cabinet to get to both parts of the switch:

See the following illustrated description of how to do it.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=131&osCsid=0da65cea0e338fe930b1fde153a243f0

All told it's about a 15 minute job.

Jan 10, 2011 | Kenmore 15864/15862 Top Load Washer

1 Answer

How do you change the bag in a kenmore progressive true hepa canister vacuum?


There is a latch just under where the hose enters the main canister section, just behind the handle. Pull back on the latch to open the bag compartment. The bag will pull out of it's plastic holder, then slide the new bag all the way in and close the lid.

Apr 14, 2010 | Kenmore 25512/ 25513 Progressive Canister...

1 Answer

B1765 tefal Kettle lid will not remain closed. I


Use a dremel and cut 2-3mm of the plastic away from each side of the sliding latch. This allows the latch to extend to its normal position. Works as new!

Oct 31, 2009 | Tefal Kitchen Appliances - Others

1 Answer

How do I turn on my tillia foodsaver my friend lent to me?


Put food in bag. Open lid using latch to right if necessary to release. Put bag in sealer. Close lid. Close latch. Push vaxuum or seal to activate

Sep 28, 2009 | Tilia FoodSaver V2240

2 Answers

Lid won't close


You might have the vacuum bag in incorrectly. Pull your vacuum bag all the way out, and check the cardboard for arrows (as some bags are cut to go in one way, and one way only). If your vacuum has a cartridge that the vacuum bag goes into, make sure that this is seated completely, securely, and correctly. After you have checked all of this, seat your lid meaning make sure it is going to sit correctly on the housing, then as you are closing the lid, check the latch as it begins to close - making sure that the male and female portions are going to match up. You may have to give it a little pressure, but should not have to put enough pressure to break anything. Good luck.

Jan 21, 2009 | Kenmore 25512/ 25513 Progressive Canister...

1 Answer

Kenmore oven door stuck closed


if you open the lid on your stove,you will probably be able to reset the switch manually (the latch).with the lid up its located toward the front behind the safety latch.(by no means attempt to force,bypass,or disable this switch)this is a safety feature designed to protect you from the high temps generated by the cleaning cycle.hope this helps.thanx for using fix-ya

Oct 08, 2008 | Kenmore 30464 / 30465 / 30469 Gas Single...

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Harvey Mahal

Level 2 Expert

39 Answers

Kristen Denison
Kristen Denison

Level 1 Expert

13 Answers

James Hensley
James Hensley

Level 2 Expert

161 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...