Question about KitchenAid KSB5 Ultra Power Work Top Blender

1 Answer

My blender seems to spin without the glass blender "jar" in place. Once the blender is put on top, the blade will not spin.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Your blade assembly is corroded. take it off, and using a rag, grab the blades. using another rag, grab the other end (probably rubber) and turn CLOCKWISE - it's threaded reverse, so you have to turn to the right to loosen, not the left like usual. I had to clean out the rod that connects to the blades - it was all nasty and corroded. I cleaned it with my Dremel and regreased with a tube of grease I keep in the garage, cleaned all other parts with some Dawn, dried well, reassembled, and works almost like new. I'm guessing I ran it too long without pulsing the motor and the heat corroded the rod that's connected to the blades. OR you can buy a replacement blade unit for about $10 online on a blender parts site

Posted on Jan 15, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you mount up a blender?


The rubber ring goes between the jar and the blade assy housing. It never goes under the blade assy, always to the jar.

Jun 01, 2014 | KitchenAid 5-speed Blender With Glass...

1 Answer

Blender glass jar is leaking at base


It will either be the rubber gasket (it goes between the glass jar and the blade assy) or it could be a worn bearing/bush around the chopping blade shaft. Replace either the gasket or the blade assy.

Apr 02, 2014 | KitchenAid 5-speed Blender With Glass...

1 Answer

Hello, I didn't see model #BBL600XL which is what


The jar has to be on for it to blend.

If you replace the jar first check the printing on your old jar. If your jar has blue print you will need a new jar and blade, Breville redesigned the jar and now the old blades don't work with the new jars. You tell the difference between the jars by the print color, old is blue, new is white.


BBL600XL/06A jar part number
BBL600XL/14A blade part number

Contact Breville at 1-866-273-8455 for service center locations.

Mar 23, 2011 | Breville BBL550XL 5-Speed Blender

1 Answer

Blender seems to run right until you put glass jar on.runs very slow.


Hi,
Disassemble the base from the jar, and check the placement of the gasket. Reassembly, with the jar upside down is gasket, blades, then base. While disassembled, rotate the blades by hand just to make sure that they aren't in a bind. Replace if defective.

--W/D--

Mar 06, 2011 | Hamilton Beach 50754 WaveStation 10 Speed...

1 Answer

Connection between the motor and the blender unit (where the spinning takes place) - get extremely hot and blender does not seem to blend well. Motor works fine without the top - and the top seems to spin...


Replace the blade assembly immediately. They are available from Cuisinart's website. Sugars and other stuff can gum up the blade assembly over time, so it will periodically need to be replaced. A quick and easy way to keep the blade assembly clean and working longer is to put water and a drop of dishwashing soap in the blender after use and run the blender at low speed for 15-20 seconds - an old Osterizer trick.

Jul 15, 2009 | Cuisinart CBT-500 SmartPower Premier Work...

2 Answers

Blade doesn't spin freely


Here's the parts order form from Waring:
http://www.waringproducts.com/ret/parts/

Once you receive the parts, unscrew the collar from the bottom of the jar, and the old gasket and blade assembly will pop out - sometimes you have to peel the gasket apart from blender jar, but not always.

-Tha Mp3 Doctor

Mar 26, 2009 | Waring MX1000R Blender

5 Answers

Waring blender - new blade


I just figured it out. The key is you need to think in terms of keeping the blades and the large washers separate. Here's what you do.
Thread the blade through the glass and use the white rubber gaskets against the glass and the stainless gaskets against the hardware. Then tighten the whole enchilada to the blender with the main nut (that goes on the bottom outside of the blender). Then once that's nice and tight tighten the flange that catches the blender teeth to the remaining portion of the protruding threads. Make sure you use the copper colored gasket first then the stainless washer then the stainless flange. Tighten that real good and you should be good to go.
To check if you've done it right spin the flange. If the blades spin independent of everything else you're good to blend away!

Feb 23, 2008 | Blenders

2 Answers

Replacement glass jug?


I will buy the blade set from you? I will return....

Nov 14, 2007 | Bosch MMB2000 Work Top Blender

2 Answers

Cuisinart sealing gasket


The gasket goes between the cutting assembly and the glass. So you slip it on over the top of the blades and then put the glass jar over top of that. Screw the bottom cap on to tighten everything together.

Aug 15, 2007 | Cuisinart SPB-7 SmartPower Work Top...

Not finding what you are looking for?
KitchenAid KSB5 Ultra Power Work Top Blender Logo

618 people viewed this question

Ask a Question

Usually answered in minutes!

Top KitchenAid Blenders Experts

Appliance engineer

Level 2 Expert

185 Answers

ThaMp3Doctor
ThaMp3Doctor

Level 3 Expert

8597 Answers

Cindy Wells

Level 3 Expert

6063 Answers

Are you a KitchenAid Blender Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...