Question about Whirlpool Ultimate Care II LSQ9564J Top Load Washer

1 Answer

Waher works fine until spin cycle and then bangs around like your beating a drum? please help

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

One possible solution is to check the springs for the tub they are underneath there are 3 of them.. also the brackets that hold them in place might have rusted out

Posted on Oct 15, 2009

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Out of balance when spin starts


Hi dear. Your machine needs new shock absorbers and drum tension springs replacement. I can advise to contact your local Miele center. Thanks.

Apr 01, 2016 | Miele Washing Machines

1 Answer

Kenmore 400 washer


Try redistributing the blanket evenly around the agitator.

Jun 11, 2017 | Washing Machines

1 Answer

Drum is loose during Spin and Rinse cycle and banging against side of washer


If it is under warranty, call Whirlpool at 1-866-698-2538. If it is out of warranty, try running the washer with no clothes in it in spin cycle. If it runs fine empty, it may be that when you had clothes in it they were not balanced evenly in the tub. If it runs off balance when empty, then a spring may have broken or come off. Contact an appliance repairman.

Oct 31, 2013 | Whirlpool WTW4880AW 3.4 cu. ft. Top Load...

1 Answer

Hard bang on spin with my frigidaire gallery frontload washer


Hi,
When my washer did that, I found that the shocks that hold the tub were bad...

Check out this tip I wrote about that...

https://www.fixya.com/support/r3663122-washer_problems_washer_noise_when

heatman101

Apr 15, 2010 | Frigidaire GLTF1040A Front Load Washer

1 Answer

Kenmore 80 Series washing machine - loud banging at end of spin


With the lid open, set the cycle to spin and press the lid switch button with a pen. Wait until the drum gets to full speed and release the lid switch. If the drum makes a knocking/ thumping noise and doesn't stop spinning within 2-3 seconds, the basket drive block is worn and needs to be replaced. (The basket drive block is located on the gearcase drive shaft, under the tub and agitator) If this has been happening for a long time you may need to replace the brake and drive tube assembly as well.
5df3c5a.jpeg
Basket drive block part number is 389140

If that's not it, let me know and I will try to help you further.
Good luck!

Mar 10, 2009 | Kenmore Washing Machines

1 Answer

Maytag LAT9806AAE- Top Load Waher- Loud Banging During Spin Cy


Damper pads, P/N 203956, $23 at searspartsdirect.com might do the job. Can't put them in yourself though, unless you are the Maytag man. Look for felt pads at the bottom of the cabinet or black dust around the damper at the bottom.
Other, more expensive problems might be a warped drum or a bad transmission. Are the springs o.k.?

Jan 18, 2009 | Washing Machines

1 Answer

Scholtes (or Ariston) "KCD12T UK" waher/dryer made terrible racket when spinning & now has loose drum, how do I get to it? Bearing on drive-belt wheel on back of tub feels fine, no looseness...


Could be failure of the drive spider. Do not use the machine until you've had it checked. If it lets go completely, damage could be very serious.

Feb 02, 2018 | Washing Machines

1 Answer

Thumping and banging


make sure all shipping pins are out the tub should move all around from side to side if it level still bangs its eather the balance ring top basket are there 3 slides on a plate above the motor just put some silacone oil on tham move around

Feb 09, 2008 | Kenmore 24032\24036 Top Load Washer

2 Answers

Maytag washer bangs during spin cycle


chances are you had a blockage in the pump and it tried to spin with the water still in the drum. check the bottom hose and filter for blockages so it does not occur again.

Jan 19, 2008 | Washing Machines

Not finding what you are looking for?
Whirlpool Ultimate Care II LSQ9564J Top Load Washer Logo

Related Topics:

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...