Question about RCA RCR311B Remote Control

1 Answer

I don't have a code search button on my philips universal remote. how do I program it

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 162 Answers

Manual Code Search and Entry 1. Manually turn on the TV
2. Press and hold the TV button The illuminated ON•OFF key turns on and remains on.
3. While holding the component key down, press and hold the ON•OFF key. The illuminated ON•OFF key turns off.
4. After holding down both keys for three seconds, the illuminated ON•OFF key turns back on.
5. Release both keys. The illuminated ON•OFF key remains on. TIP: Throughout the programming of each key, be sure to keep the remote pointed at the IR sensor of the component you are currently programming the remote to control.
6. Press and release the ON•OFF key repeatedly until your component turns off. Each time you press the ON•OFF key, the illuminated ON•OFF key blinks, and the next
code in the list is sent. This process continues until all of the codes in the Code Lists have been searched. If your component turns off, you have found the correct code.
TIP: Because there are so many codes, you may have to press the ON•OFF key many times-possibly up to 200 times.
7. Once you have found the correct code, you must save the new code by pressing and releasing the STOP key. The illuminated ON•OFF key turns off. You must press the STOP key to save the code or the correct code will not be stored!
8. To confirm that the component key is programmed with the correct code for maximum functionality, test the component. Attempt to control a variety of the component's functions with the remote. If some of the features of your components do not work, try programming the remote with a different code in the list until you find the code that allows the remote to control the majority of your component's functions. Different codes can provide different levels of functionality.

Posted on Oct 14, 2009

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I am using a Philips SRU3003WM/17 Universal Remote with my Sylvania TV Model number 64119E. When programming the remote some strange numbers appeared on the screen and now I cannot get them off. The...


Hi there,

Well your Philips universal remote control comes with a list of codes for devices by brand name.
Find the first code for the brand name and type of device you wish to program. Turn all of your devices off, and then manually turn on the device you want to program.
Press the Setup button on your the universal remote and continue to hold it down until the indicator light stops flashing and remains solid. Release the Setup button. Press the Mode button for the type of device you want to program on your Philips universal remote, such as the TV.Release it immediately and make sure the indicator light is illuminated. Enter the first possible four-digit code on the universal remote, and then press another button on the remote to see if the device is now programmed, such as the volume control or power button. If the device responds, you have successfully programmed your Philips universal remote. If not, turn the device off and back on and follow the steps again using the next code on the list. Repeat until the device successfully responds.

If your TV code is not listed on the manual then you can use the Remote Using Code Search Option -
Your Philips universal remote has a built-in code search feature that will find the correct code for your device. This process may take longer than using direct code entry, but can be helpful if you do not have access to the code list or if the brand for your device is not listed.

Make sure all of your devices are turned off, and then manually turn on the first device. Press the Code Search button and hold it down until the red indicator light stays illuminated. Press the Mode button for the type of device you want to program on your Philips universal remote, such as the TV button.  Release it immediately and make sure the indicator light is illuminated. Press either the Channel button until the device responds. You may have to press the button up to 300 times. Each time you press the button, the Philips universal remote tries a new code. When the code works, press the Mute button on the Philips universal remote and the code will be stored.

I thing you wrongly do the second option that creates the problem. No issue, if your tv code not listed on the manuals then you can go with the second (code search) solution. Please post comments for further help or information.........

Good Luck!!

Thanks

Jul 31, 2010 | Televison & Video

1 Answer

Need to program my tv and dvd player to the remote


Hi,

Please follow the steps below

Program the First Device by Entering Direct Codes

1.Turn all of your devices off, and then manually turn on the device you want to program.
2.Press the Setup button on your the universal remote and continue to hold it down until the indicator light stops flashing and remains solid.
3.Release the Setup button
4.Press the TV button.
5.Release it immediately and make sure the indicator light is illuminated.
6.Enter the first possible four-digit code on the universal remote, and then press another button on the remote to see if the device is now programmed, such as the volume control or power button.
7.If the device responds, you have successfully programmed your Philips universal remote.
8.If not, turn the device off and back on and follow the steps again using the next code on the list. Repeat until the device successfully responds.

How to Program a Remote Using Code Search
1.Turn all of your devices off, and then manually turn on the device you want to program.
2.Press the Setup button on your the universal remote and continue to hold it down until the indicator light stops flashing and remains solid.
3.Release the Setup button
4.Press the TV button.
5.Release it immediately and make sure the indicator light is illuminated.
6.Press either the Channel button or the Play button until the device responds. Each time you press the button, the Philips universal remote tries a new code.
7.When the code works, press the Mute button on the Philips universal remote and the code will be stored.


To get the universal remote codes please visit below solution

http://www.fixya.com/support/t5395701-universal_remote_code_phillips
Thanx

Jul 27, 2010 | Philips Universal PH301S Remote Control

2 Answers

Need codes for philips universal remote on a toshiba TV


i don,t know the code to this remote it is a ge universal remote

Jan 06, 2009 | Philips Universal PH301S Remote Control

1 Answer

Philips universal tv remote not working


http://www.remotecodelist.com/remotes/magnavox/Philips-Magnavox_PM525S.pdf
Thisis the user's manual for a Phillips remote control. There is a list ofcodes in it. They should be rather universal. There's also instructionsas to how to program it. I believe that there is a way to program itwithout using the codes.

Programming with Code Search

1. Manually turn on the device (TV, VCR, etc.) to be controlled.

2. Press and hold Code Search button until the red indicator stays on. Release the Code Search button.

3. Press and release the desired mode button (TV, VCR, etc.). The red indicator blink, then stays lit.

4.Press the Channel Up button repeatedly (up to 300 times) until thedevice could be controlled changes channel. The red indicator blinks,then stays lit. If you accidentally overshoot the code required, pressthe Channel Down button to backtrack through the library until thedevice changes channel. Pressing Channel Up changes direction toforward again. Press and release the Mute button to install the code.

Hope this helps :)

Jul 29, 2008 | Philips Televison & Video

1 Answer

I have a philips pm335 universal remote control


I went to the Phillips website and I wasn't able to find a code list. However, I did find the instructions to program your remote with "code search". Basically, it might take some time, but you can program your remote without the code list.

Programming with Code Search

1. Manually turn on the device (TV, VCR, etc.) to be controlled.

2. Press and hold Code Search button until the red indicator stays on. Release the Code Search button.

3. Press and release the desired mode button (TV, VCR, etc.). The red indicator blink, then stays lit.

4. Press the Channel Up button repeatedly (up to 300 times) until the device could be controlled changes channel. The red indicator blinks, then stays lit. If you accidentally overshoot the code required, press the Channel Down button to backtrack through the library until the device changes channel. Pressing Channel Up changes direction to forward again. Press and release the Mute button to install the code.

Hope this helps :)

Jun 26, 2008 | Philips Universal PH301S Remote Control

4 Answers

Need codes for a philips universal remote code sheet


http://www.remotecodelist.com/remotes/magnavox/Philips-Magnavox_PM525S.pdf
This is the user's manual for a Phillips remote control. There is a list of codes in it. They should be rather universal. There's also instructions as to how to program it. I believe that there is a way to program it without using the codes.

Programming with Code Search

1. Manually turn on the device (TV, VCR, etc.) to be controlled.

2. Press and hold Code Search button until the red indicator stays on. Release the Code Search button.

3. Press and release the desired mode button (TV, VCR, etc.). The red indicator blink, then stays lit.

4. Press the Channel Up button repeatedly (up to 300 times) until the device could be controlled changes channel. The red indicator blinks, then stays lit. If you accidentally overshoot the code required, press the Channel Down button to backtrack through the library until the device changes channel. Pressing Channel Up changes direction to forward again. Press and release the Mute button to install the code.

Hope this helps :)

Jun 21, 2008 | Philips Magnavox Learning Universal Remote

1 Answer

Programing


http://www.remotecodelist.com/remotes/magnavox/Philips-Magnavox_PM525S.pdf
This is the user's manual for a Phillips remote control. There is a list of codes in it. They should be rather universal. There's also instructions as to how to program it. I believe that there is a way to program it without using the codes.

Programming with Code Search

1. Manually turn on the device (TV, VCR, etc.) to be controlled.

2. Press and hold Code Search button until the red indicator stays on. Release the Code Search button.

3. Press and release the desired mode button (TV, VCR, etc.). The red indicator blink, then stays lit.

4. Press the Channel Up button repeatedly (up to 300 times) until the device could be controlled changes channel. The red indicator blinks, then stays lit. If you accidentally overshoot the code required, press the Channel Down button to backtrack through the library until the device changes channel. Pressing Channel Up changes direction to forward again. Press and release the Mute button to install the code.

Hope this helps :)

Jun 09, 2008 | Philips Universal PH301S Remote Control

1 Answer

Help


http://www.remotecodelist.com/remotes/magnavox/Philips-Magnavox_PM525S.pdf
This is the user's manual for a Phillips remote control. There is a list of codes in it. They should be rather universal. There's also instructions as to how to program it. I believe that there is a way to program it without using the codes.

Programming with Code Search

1. Manually turn on the device (TV, VCR, etc.) to be controlled.

2. Press and hold Code Search button until the red indicator stays on. Release the Code Search button.

3. Press and release the desired mode button (TV, VCR, etc.). The red indicator blink, then stays lit.

4. Press the Channel Up button repeatedly (up to 300 times) until the device could be controlled changes channel. The red indicator blinks, then stays lit. If you accidentally overshoot the code required, press the Channel Down button to backtrack through the library until the device changes channel. Pressing Channel Up changes direction to forward again. Press and release the Mute button to install the code.

Hope this helps :)

May 18, 2008 | Philips Universal PH301S Remote Control

1 Answer

Remote codes for philips universal


http://www.remotecodelist.com/remotes/magnavox/Philips-Magnavox_PM525S.pdf
This is the user's manual for a Phillips remote control. There is a list of codes in it. They should be rather universal. There's also instructions as to how to program it. I believe that there is a way to program it without using the codes.

Programming with Code Search

1. Manually turn on the device (TV, VCR, etc.) to be controlled.

2. Press and hold Code Search button until the red indicator stays on. Release the Code Search button.

3. Press and release the desired mode button (TV, VCR, etc.). The red indicator blink, then stays lit.

4. Press the Channel Up button repeatedly (up to 300 times) until the device could be controlled changes channel. The red indicator blinks, then stays lit. If you accidentally overshoot the code required, press the Channel Down button to backtrack through the library until the device changes channel. Pressing Channel Up changes direction to forward again. Press and release the Mute button to install the code.

Hope this helps :)

May 14, 2008 | Philips Universal PH301S Remote Control

1 Answer

Remote code


http://www.remotecodelist.com/remotes/magnavox/Philips-Magnavox_PM525S.pdf
This is the user's manual for a Phillips remote control. There is a list of codes in it. They should be rather universal. There's also instructions as to how to program it. I believe that there is a way to program it without using the codes.

Programming with Code Search

1. Manually turn on the device (TV, VCR, etc.) to be controlled.

2. Press and hold Code Search button until the red indicator stays on. Release the Code Search button.

3. Press and release the desired mode button (TV, VCR, etc.). The red indicator blink, then stays lit.

4. Press the Channel Up button repeatedly (up to 300 times) until the device could be controlled changes channel. The red indicator blinks, then stays lit. If you accidentally overshoot the code required, press the Channel Down button to backtrack through the library until the device changes channel. Pressing Channel Up changes direction to forward again. Press and release the Mute button to install the code.

Hope this helps :)

Apr 15, 2008 | Philips Universal PH301S Remote Control

Not finding what you are looking for?
RCA RCR311B Remote Control Logo

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76204 Answers

matt martin
matt martin

Level 3 Expert

1257 Answers

Cindy Wells

Level 3 Expert

6065 Answers

Are you a RCA Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...