Question about Kenmore 659 Electric Dryer

Open Question

Kenmore dryer model #417, beeping and error code 68 stackable was washing below empty not running dryer started beeping and still is, had to unplug, flashing err 68???

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
catriver

Ron Marek

  • 878 Answers

SOURCE: Dryer turns itself on & beeps, then off again

aye, see if you can enter the diagnosis mode. What we are looking for is the F-02 code. This will flash when there is a stuck button or user interface problem and only displayed in the test mode. With the unit plugged in and all indicator lights off, select any button except stop. Press for 3 seconds, release for 3 seconds, press for 3 seconds, release for 3 secnds and press for 3 seconds. If you did it right 88 should appear. Press the same button again and if there is a error, it should show up. If no error code shows, open the consol and check the p-5 connector. This will be the interface ribbon to the board. Reseat it and see if the problem stops. Catriver

Posted on Jul 16, 2007

Ad

Anonymous

  • 146 Answers

SOURCE: kenmore dryer 417.84072300

Check you circuit breaker. Even if it doesn't look tripped reset it anyhow. This is a power interrupt code.

Posted on Dec 22, 2007

Anonymous

  • 525 Answers

SOURCE: KENMORE ELITE OASIS HE CANYON CAPACITY DRYER

Below is a link that will help you with parts and diagnostic procedures that are specifically tuned to your manufacturers data plate information. This model is manufactured by Whirlpool, so maybe you can locate your model's failure codes.
http://www.repairclinic.com/0078.asp

If my assistance helped resolve this issue, please show your appreciation by rating how effective my advice was in resolving this issue.
Thank you,
Dave E. (Illeagle)

"Your satisfaction is my personal reward"

Posted on Jun 22, 2008

Anonymous

  • 1 Answer

SOURCE: 4E problem on kenmore dryer

Same problem, no panel lights, nothing, but drum light works. Several postings on othe sites say the cuicuitry board is faulty. Sears, in the Phillippines, or India, do notheing. Paid lots for this dryer, live alone and really don't abuse it or even use it that much. Is the there a class action suit maybe? all I want is for it to work!

Posted on Sep 04, 2008

Anonymous

  • 1 Answer

SOURCE: KENMORE ELITE OASIS HE CANYON CAPACITY DRYER

I have the same problem. Started a few days ago. My model number is 67086. How can I fix this? I have 2 year old twins and I'm concerned about the safety of this machine.

Posted on Nov 25, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Model 417-94702300 need help removing agitator


The agitator is just a slip fit over a splined shaft, so if the part will not move after the retaining nut is removed it is rusted to the shaft and you have to do whatever it takes to break it free.

Oct 16, 2016 | Kenmore 3.4 cu. ft. Capacity Compact...

1 Answer

Frigidaire affinity error code 68


what is the name and model of these dryer.rate these for clean solution
thanks

Jan 16, 2013 | Dryers

1 Answer

Kenmore Elite washer service code CLL SrU


Re: Kenmore Elite 417; error CLL SRV We have well water and I think my error message and locked door were because the machine was trying to plump water and not getting any. I heard the error beeping and sent to check it out. There was another noise that didn't stop even after unplugging the washer, although the beeping did, which finally stopped after I turned off the water valves. Press and Hold the power button down to unlock the door and retry. If you still have trouble, call for service.

Sep 25, 2012 | Washing Machines

1 Answer

I have a Sears - Kenmore Stackable gas dryer. Model # 417.94042500.I'm looking for a photo, to compare details. Can you help?


what problem are you having?this is made by frigidaire because it starts with 417.what are you looking for or what details are you talking about.

Apr 16, 2011 | Kenmore Dryers

1 Answer

Kenmore dryer,, looking for adiagram for the belt on a kenmore dryer


Below are the belt diagrams for Kenmore dryers.

jahn27_201.jpg
Figure 1. Whirlpool-made Kenmore dryers with removable back panel, filter on top, and model numbers starting with 110 or C110.

jahn27_202.jpg
Figure 2. Whirlpool-made Kenmore dryers with non-removable back panel, filter below the door, and model numbers starting with 110 or C110.

jahn27_203.jpg
Figure 3. Frigidaire-made Kenmore dryers (model numbers starting with 417).

Mar 01, 2011 | Kenmore Dryers

1 Answer

Kenmore front load washer, model 417


Washer dryers often have cold water valves with 3 separate solenoids. One for the main wash and rinses (which is clearly ok) and one for the condition rinse (to take the fabric conditioner down) which is probably ok too, and the 3rd one is for the dryer. It's possible this 3rd solenoid has failed.

Washer dryers need on a steady trickle of cold water running into the condenser chamber to convert the steam into water, which then gets pumped down the drain.

e10 means that there is a problem with the water supply.
a condenser dryer needs cold water to operate properly. the e10 code will appear if:
1. the water is turned off
2.the water pressure is too low.
3.the solenoid valve is open circuit
4.there is a problem with the pressure switch (least likely)

Cold valve is at the end of blue inlet pipe remove lid and you will see it.

f E10 is only appearing when trying to dry, the problem almost certainly is the condenser valve solenoid open circuit. The green solenoid on the inlet valve. Should read about 4000 ohms.

My money would be on the solenoid coil being open circuit. The coil can be canabalised from most valves although you may have to modify the connections. For simpler repairs - contact Zanussi and get the entire triple inlet water valve to swap out.


http://www.zanussi-electrolux.co.uk/files/unitedkingdom_english/0-999/zanussi%20error%20codes.swf


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Oct 15, 2009 | Kenmore Washing Machines

1 Answer

Sears Model 417 stackable washer and dryer


The model that you provide is incomplete. However, if the washer loads from the top, they cannot be separated. If it loads from the front, they can.

Apr 10, 2009 | Kenmore 98702 Stacked Washer/Dryer

1 Answer

Blinking error codes?


Unplug the machine for 30 minutes , plug it back it, start it for 1 minute, unplug it again for 5 minutes then plug back it and it should work. If not then write back with the error codes so further diagnostics can be done

Apr 08, 2009 | Kenmore 62602 Electric Dryer

Not finding what you are looking for?
Kenmore 659 Electric Dryer Logo

Related Topics:

848 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dryers Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Ned Halaweh
Ned Halaweh

Level 2 Expert

240 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Kenmore Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...