Question about Whirlpool Ultimate Care II LSQ9549L Top Load Washer

1 Answer

WHIRLPOOL ULTIMATE CARE 2 WASHER. THE DRUM WILL NOT SPIN. SEEMS TO BE LOOSE.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Whirlpool Expert
  • 154 Answers

DRIVE BLOCK MAY HAVE UNSCREWED FROM THE TUB, CALL A REPAIRMAN

Posted on Feb 07, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Loose belt


The model you posted doen not have a belt it is a direct drive washer, with a drive coupling, the symptoms you are describing indicate a bad clutch.

Dec 27, 2011 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Whirlpool washer wont spin during spin cycle everything else appears ok.


Machine not spinning....check]
1..all water gone clean pump trap and check blocked drain
2....somehting stopping drum spin drum freely by hand.
3....too much soap use low suds soap and very little of it.
4....motor brushes wearing out...call for service for this one.
Good luck
T

Aug 07, 2010 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

I have a whirlpool ultimate care 2 top load washer no spin


Sounds as if the drive hub which the tub is attached to maybe free spinning. Not an expensive part but does require a special tool called a spanner wrench to remove and replace.

Jan 31, 2010 | Whirlpool Ultimate Care II LSQ9549L Top...

2 Answers

Spin cycle doesn't spin


you nead to check the door switch,nead to know the mod# to know what type of door switch you have.

Dec 02, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Whirlpool Ultimate Care II LSQ8243HQ0 weak spin, wet clothes


if it has a belt, it may be slipping, but you would smell a bit of burning rubber.in high use times(4 to 8 pm), the current of electric supply is low, thus less power. third, motor may need to be replaced. plz rate-bozcro

Sep 10, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Phillips Whirlpool Ultimate Care II won't spin very quickly


If this is a top loader it is possible that you have a bad clutch. sometime when your transmission leaks oil it will get into the clutch and this will cause a slower spin and possibly no spin. Tip the washer back just enough so you can see under the washer. Is there a orange/yellow sticky substance under there? If so this is trany fluid.

Jan 10, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Whirlpool Ultimate Care II drum does not spin.


Depending on your washing machine model, the drum and motor are connected by 2 plastice yellow circular pieces, with a black rubber washer in the middle with holes where the pegs or rods go into. The 2 plastic circular pieces have 3 pegs or rods if you will, that connect to the black rubber washer via 3 holes. Sometimes, one or both of the 2 plastic circular piece pegs get broken off or the rubber washer cracks and breaks apart, so that the motor will not turn the drum. If thats the case, you can purchase the 2 circular pieces and black washer piece as a set.

Jan 05, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Whirlpool ultimate care 2 washer wont spin


Are you in the Delicate Cycle? Do you have spin speed control set for slow?If both answers are no,than what is the model & serial number??

Apr 28, 2008 | Whirlpool Ultimate Care II LSQ9564J Top...

1 Answer

Sound in spninning cycle on whirlpool ultimate care 2


if its maling a loud rumbbling sound when it goes into spin then your bearings are on there way out m8 you can check this by opening the door place your palm on the font of the washer with your fingers on the inner drum now pull your fingers up and towards you if the inner drum moves ten this is your bearings if not then your suspension needs replacing m8

Jan 26, 2008 | Whirlpool Ultimate Care II LSQ9549L Top...

Not finding what you are looking for?
Whirlpool Ultimate Care II LSQ9549L Top Load Washer Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...