Question about Mitsubishi WS-55859 55" Rear Projection Television

3 Answers

Flashing green light and tv will not turn on with power button on tv or remote.

Posted by on

Ad

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mitsubishi Master
  • 14,553 Answers

THIS IS MY STANDARD ANSWER TO THIS QUESTION==SOMETIMES PEOPLE DO NOT TRY THE EASY POSSIBLE REASON--IF YOU HAVE ANY QUESTIONS LET ME KNOW---IF THE ANSWER TOLD YOU something you did not know--rate the solution----

ONLY 1 of 2 things can cause this problem----

First thing to do is remove front speaker grill--it should pull out and is secured with plastic pegs--behind it you will find an inspection plate---

Notice the one or two pairs of wires coming from the front keyboardflashing green light and tv will not turn on with - 2.gif of the set---remove the inspection plate and follow the wires to the right--you can unplug both plugs(most have two and they are marked with letters and different sizes so you cannot get them wrong)

The idea here is to remove the front keyboard with its reset button etc from the circuit---You will still be able to try to turn the set on with the remote---

These sets have a Receiver that is called a DM board--(large metal box to the left as you look from the back) and if the power goes out the green light will blink for about 70 seconds and then go out---it is the Receiver booting up. It is called the DM board.

If disconnecting the keyboard allows the set to turn on--you have a bad reset switch and two choices---either operate the set only with the remote or to remove the front screen and get at the reset switch (it is tiny) and remove and/or replace it.

If disconnecting the keyboard does not restore the set to operation---the receiver is bad---there are 4 or more caps and some pico fuses that can fail in that unit---Mitsubishi no longer sells or repairs these--if it is bad and not the caps there is a company you can send the unit to and have it repaired--if you need to know their name let me know---

You can call them and get a quote for repairing the receiver.


Let me know what more information you need--I am here to help.


SD TECH

Posted on Oct 30, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 273 Answers

There are capacitors that fail in the dm module and will have to be replaced to get the set to work again
if you have the tools soldering station and abilaity you can repair it your self if not you may want to enlist some local help with it
cost depending on area 325 to 385 for the repair

Posted on Oct 30, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hi my name Eng Sin . I have problem with my tv WS-55859 . one of capacitor i got a reading start 34k then moved up until no reading detected . Please respond back if this is something to bad to worry about or is it nothing?.
Flashing green light and tv will not turn on with .

Posted on Dec 19, 2009

3 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Anonymous

SOURCE: Mitsubishi WS73713 - Now working - Timer light flashing.

The capacitors on the dm board are probably bad. I called mitsubishi and they agreed to pay for the part even though my tv is four years old. MITSUBISHI cust # is 1-800-332-2119

Posted on Jan 24, 2008

Anonymous

SOURCE: TV makes chirping sound and power button blinks, T.V. does not turn on

Me too! help!

Posted on Apr 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mitsubishi wd-73738 turns itself back on


Hi,

It sound like the remote is powering off the cable box but not the TV. The remote control may need to be reprogrammed to the TV. When you press power it may only power off the Cable box. At that point, try pressing the TV button on your remote and then Power. If it does not power off the tV after pressing the tV button, the remote may need to be reprogrammed to the tv. Cable companies usually have the codes needed to program their remotes to the TVs.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/laura_08254539050d64db

Jul 09, 2016 | Mitsubishi WD-73738 73" 3D Ready DLP HDTV...

1 Answer

Program code for Directtv Universal remote.


You can see an easy step-by-step guide to programming your remote right on your TV screen:
sm_cl_blu__number1_icon.pngPress MENU on your remote control sm_cl_blu__number2_icon.pngSelect Settings & Help sm_cl_blu__number3_icon.pngSelect Settings sm_cl_blu__number4_icon.pngSelect Remote Control sm_cl_blu__number5_icon.pngSelect Program Remote and follow the on-screen prompts img_remote_control_tv_sol1.jpg You can also use the manual method below: sm_cl_blu__number1_icon.pngMake sure your TV and your receiver are both on. sm_cl_blu__number2_icon.pngUse this tool to look up the 5-digit code for your TV. There could be more than one code for your brand of TV. sm_cl_blu__number3_icon.pngSlide the MODE switch on your remote control to the TV position. sm_cl_blu__number4_icon.pngPress and hold the MUTE and SELECT buttons at the same time until the green light at the top of your remote flashes twice, then release both buttons. sm_cl_blu__number5_icon.pngUsing the number buttons, enter the 5 digit code for your brand of TV. The green light under the TV should flash twice. sm_cl_blu__number6_icon.pngAim the remote at your TV and press the VOLUME UP button. If the volume doesn't increase, repeat Steps 3-5, trying a different 5-digit code for your TV. If your remote control fails to program using all available codes, try scanning for additional codes. If one of the codes worked, proceed to the next step. sm_cl_blu__number7_icon.pngPress and hold MUTE and SELECT buttons until the green light at the top of your remote control flashes twice. sm_cl_blu__number8_icon.pngEnter 9-6-0 using the keypad on the remote control. The green light should flash twice again. sm_cl_blu__number9_icon.pngSlide the MODE switch on your remote control to the DIRECTV position. img_remote_control_tv_sol2.jpg Follow these steps to scan for additional TV codes using your DIRECTV remote: sm_cl_blu__number1_icon.pngSlide the MODE switch on your remote control all the way to the right to the TV position. sm_cl_blu__number2_icon.pngPress and hold the MUTE and SELECT buttons at the same time until the green light at the top of your remote flashes twice, then release both buttons. sm_cl_blu__number3_icon.pngUsing the number buttons, enter 9-9-1. The green light on your remote should flash twice. sm_cl_blu__number4_icon.pngAim the remote at your TV and press CHAN/PAGE UP button. Tap the CHAN/PAGE UP button repeatedly until the TV powers off. sm_cl_blu__number5_icon.pngWhen the TV powers off, press and release the SELECT button. Note: If the green light flashes three times before your TV responds, then all codes have been cycled through. Our remote controls are guaranteed to program to your DIRECTV receiver, but your TV may not be compatible with our remote control.

Jul 08, 2014 | GE JASRM24912 Remote Control

1 Answer

How can i set up my direct tv remote to my Haier tv


How to scan for TV codes on your DIRECTV remote
  • Make sure your TV is turned on.
  • Slide the mode switch at top of remote to "TV".
  • Press and hold the MUTE button. This is located above the number 1 button.
  • While still holding down MUTE, press and hold the SELECT button until green light at the top of the remote flashes twice.
  • Then enter 9-9-1, the green light on remote should flash twice.
  • Point remote at TV and press CHANNEL UP button. Tap the CHANNEL UP button repeatedly until the TV powers off.
  • When the TV powers off, press and release the SELECT button.

Feb 13, 2013 | Haier HL22XLE2 - HL22XLE2 22 LED-LCD TV -...

1 Answer

How to program Direct TV remote


How to program your DIRECTV remote control:

Press MENU on remote.
Select "Parental, Favs and Setup".
Select "System Setup".
Select "Remote".
Select "Program Remote".

While aiming remote at device, follow onscreen instructions to program remote to TV, DVD, or other device.

How to program the white DIRECTV remote to your TV

Look up the control codes for your DIRECTV remote control.
Make sure your TV is turned on.
Slide the mode switch at top of remote to "TV".
Press and hold the MUTE button. This is located above the number 1 button.
While still holding down MUTE, press and hold the SELECT button until the green light at the top of the remote flashes twice.
Enter the first TV code you have. The green light on remote should flash twice.
Aim remote at TV and press PWR button once. The TV should power off.
Once the TV is able to power off/on and control the volume, slide the mode switch at the top of the remote back to the left (DIRECTV). Your remote is now programmed.

If the TV does not power off, repeat steps 4, 5, 6, and 7, using the next code for your TV brand.

If remote control fails to program using all available codes, try scanning for the code.

How to scan for TV codes on your DIRECTV remote

Make sure your TV is turned on.
Slide the mode switch at top of remote to "TV".
Press and hold the MUTE button. This is located above the number 1 button.
While still holding down MUTE, press and hold the SELECT button until green light at the top of the remote flashes twice.
Then enter 9911, the green light on remote should flash twice.
Point remote at TV and press CHANNEL UP button. Tap the CHANNEL UP button repeatedly until the TV powers off.
When the TV powers off, press and release the SELECT button.

Note: If the green light flashes three times before TV responds, then all codes have been cycled through. Our remote controls are guaranteed to program to your DIRECTV receiver, however your TV may not be compatible with our remote control.

You can find more help in the Remote Controls section of our Technical Forums at forums.directv.com. You can also use our Interactive User Guide to learn the ins and outs of your remote control.

Apr 11, 2012 | Audio Players & Recorders

1 Answer

I am trying to program my "Direct TV" remote to my Samsung LCD TV Series 5 and can not find the 5 digit code needed to do so.


If you have a DIRECTV white remote, press "menu" then "settings," "setup," "remote", and follow the on-screen instructions.
If using a gray or black remote,
  • Make sure your TV is turned on.
  • Slide the mode switch at top of remote to "TV".
  • Press and hold the MUTE button. This is located above the number 1 button.
  • While still holding down MUTE, press and hold the SELECT button until green light at the top of the remote flashes twice.
  • Then enter 9911, the green light on remote should flash twice.
  • Point remote at TV and press CHANNEL UP button. Tap the CHANNEL UP button repeatedly until the TV powers off.
  • When the TV powers off, press and release the SELECT button.
  • Sep 07, 2011 | Televison & Video

    1 Answer

    Can set up th remote control for this tv with the direct tv cable remote


    Here's how to scan for TV codes on your DIRECTV remote

    1.Make sure your TV is turned on.

    2.Slide the mode switch at top of remote to "TV".

    3.Press and hold the MUTE button. This is located above the number 1 button.

    4.While still holding down MUTE, press and hold the SELECT button until green light at the top of the remote flashes twice.

    5.Then enter 991, the green light on remote should flash twice.

    5b. Press 1 again (it will flash twice again), then you press the power on button at the very top right.

    6.Point remote at TV and press CHANNEL UP button. Tap the CHANNEL UP button repeatedly until the TV powers off.

    *If you hit channel up very fast, you risk going past the code. Pressing channel down will back it up. I alway hit channel up very fast till the tv turns off, then back it up slowly till it comes back on.

    7.When the TV powers off, press and release the SELECT button.

    *Note: If the green light flashes three times before TV responds, then all codes have been cycled through. Our remote controls are guaranteed to program to your DIRECTV receiver, however your TV may not be compatible with our remote control.

    Mar 05, 2011 | Curtis LCD2425A TV

    1 Answer

    Need rca crk17sa users guide for codes for Magnavox TV


    Ok it took me a while. Go to this link to find the codes for you remote: 10054 is the most used code for Magnavox. I hope this helps you out. Good Luck!!!!!!!
    http://www.directv.com/DTVAPP/content/remote_codes

    Here's how to program your DIRECTV remote control:
    1. Press MENU on remote.
    2. Select "Parental, Favs and Setup"
    3. Select "System Setup"
    4. Select "Remote"
    5. Select "Program Remote"
    While aiming remote at device, follow onscreen instructions to program remote to TV, DVD, or other device.


    How to program the white DIRECTV remote to your TV
    1. Look up the control codes for your DIRECTV remote control.
    2. Make sure your TV is turned on.
    3. Slide the mode switch at top of remote to "TV".
    4. Press and hold the MUTE button. This is located above the number 1 button.
    5. While still holding down MUTE, press and hold the SELECT button until the green light at the top of the remote flashes twice.
    6. Enter the first TV code you have. The green light on remote should flash twice.
    7. Aim remote at TV and press PWR button once. The TV should power off.
    8. Once the TV is able to power off/on and control the volume, slide the mode switch at the top of the remote back to the left (DIRECTV). Your remote is now programmed.
    If the TV does not power off, repeat steps 4, 5, 6 and 7, using the next code for your TV brand.
    If remote control fails to program using all available codes, try scanning for the code.


    How to scan for TV codes on your DIRECTV remote
    1. Make sure your TV is turned on.
    2. Slide the mode switch at top of remote to "TV".
    3. Press and hold the MUTE button. This is located above the number 1 button.
    4. While still holding down MUTE, press and hold the SELECT button until green light at the top of the remote flashes twice.
    5. Then enter 991, the green light on remote should flash twice.
    6. Point remote at TV and press CHANNEL UP button. Tap the CHANNEL UP button repeatedly until the TV powers off.
    7. When the TV powers off, press and release the SELECT button.
    Note: If the green light flashes three times before TV responds, then all codes have been cycled through. Our remote controls are guaranteed to program to your DIRECTV receiver, however your TV may not be compatible with our remote control.

    Mar 08, 2010 | Televison & Video

    1 Answer

    Flashing green light


    Did you try this yet

    SYSTEM RESET
    If the TV will not respond to either the remote control
    or the front panel controls and/or will not power Off,
    press the SYSTEM RESET button with a pointed item
    like the end point of a paperclip. The TV will turn Off
    and the TIMER light will flash quickly for about one
    minute. When the TIMER light stops flashing, you may
    turn on the TV again. Changes you made the last time
    the TV was On before you used the SYSTEM RESET
    button may be lost, however, the changes you made
    previously are not lost.
    POWER/TIMER Indicator
    The green light is a multi-function indicator. This light
    will flash rapidly for about one minute each time the TV
    is plugged into the wall electrical outlet, when power
    is restored after a power failure, or using the SYSTEM
    RESET button. Do not attempt to turn on the TV again
    during this period. Wait for the flashing to stop and
    the light to turn off, before attempting to turn the TV
    on. While the TV is powered on, the light illuminates
    steadily. If the TV has been programmed to turn on
    automatically using the Timer feature,

    Sep 21, 2009 | Mitsubishi WS-65515 65" TV

    1 Answer

    Green flashing power indicator light


    similar problem with my Sony. Unplugging for 36 hours solved the problem for me

    Sep 29, 2007 | Samsung HPN5039 50 in. Plasma HDTV

    Not finding what you are looking for?
    Mitsubishi WS-55859 55" Rear Projection Television Logo

    744 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mitsubishi Televison & Video Experts

    matt martin
    matt martin

    Level 3 Expert

    1257 Answers

    The Knight
    The Knight

    Level 3 Expert

    76204 Answers

    Ekse

    Level 3 Expert

    13434 Answers

    Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...