Question about Kitchen Appliances - Others
I purchased a new Shark steamer from Overstock.com. I read the manual and followed the instructions with the minor exception that using 8oz of water caused the steamer to overflow, so I used 6oz of water instead. I plugged it in and though it got hot, I could not get any steam out of it. I tried for 45 minutes and finally unplugged it. I tried it again several hours later and still was unable to get steam to come out. Suggestions?
Taking it apart isn't all that difficult if you are vaguely handy, have the time and the patience to dig into what it took China's best engineers years to design. And it beat either sending your $150 lump to a landfill or $$$ending it back for repair$$$. Here' what I did:
We had the same problem with ours...worked for about 6 months and quit. We were using tap water. DON'T. Use distilled only.
Tried the white vinegar trick. Nope. Tried the CLR trick. Nope. Decided to disassemble, even it was junk I might learn something.
Tools: two phillips (hex) head screwdrivers, one medium, one small (not tiny). They need to have fairly narrow shanks to fit into the deep holes on the body. Needle-nose pliers. Pair of scissors.
UNPLUG IT!!! And let it cool for at least an hour before you start and take the handle apart at the pump so it's less awkward. The boiler inside stays very hot for quite a long time, even when its unplugged.
1. Take out the multiple screws that hold the purple body together. Careful...these are cheap screws (surprised?) and the heads may strip or the plastic threads may strip. You may just ending up forcing some of the screws out. Do the screws slowly and do everything in your power to keep the screwdriver head square with the screws.
2. You can't take the two halves completely apart; the wiring is in the way. That's the biggest hassle of the whole project. That and the mop head that you can't take off. Inside you'll see a metal "boiler" about the size of a can of tomato paste. It has wiring (thin) and tubing (fat) running into it. If it's still hot, let it cool.
3. There are also four screws inside that hold the water reservoir in place. If you take those you can get easier access to the boiler, though the reservoir will still be attached to the body of the unit.
NOTE: The boiler is held in place by two brackets and four very small screws and little fiber insulation washers. DO NOT take the screws all the way out (like I did) as they are extreeeeeemly difficult to get back in place. Just loosen them about 3/4s of the way so you can move the brackets and lift out the boiler. The boiler will still be attached to its wiring. Don't disturb the wires; you just have to carefully work around them.
4. With a pair of needle-nose pliers, squeeze the little spring clamp that holds the tube that runs from the water reservoir into the boiler and slide it up the tube a bit and _carefully_ slide the tube off the nipple on the boiler. Mine cracked at the end when I did this so I needed to trim the end square again with scissors. A sharp box knife would work too, but use the scissors to trim the webbed insulation fabric if needed.
4. On the other end of the boiler is a tube that goes to the mop head. Undo the clip there, too, and slide it back and again slide off the tube.
5. Look at the nipple for the tube that goes to the mop head. It is probably clogged with calcium deposits that the vinegar or CLR didn't touch. It will look solid. It is. That's probably your problem.
6. I took a power drill and a very small drill bit (1/16") and drilled out the calcium - it's very soft - to free up the hole. Then took the next size bit (3/32" or so) and widened the hole further, sort of like getting a root canal (ouch!). Don't drill too deeply into the boiler as you may hit something important. When it's open, left over water, vinegar or CLR will come out. You should now be able to blow through the boiler from the newly cleaned nipple, with air coming out the other hole (to the reservoir). The reservoir line must be disconnected to do this because there's a little one way valve in the reservoir line that keeps the from steam going back into the tank and not out the mop head (your drip coffee maker works the same way, as I also discovered when ours clogged...same problem: Calcium build up).
7. Return the two tubes to the boiler (don't forget to push the spring clips back in place) and reattach the boiler to the body. Aren't you glad you didn't take off the boiler brackets?
8. Before you do the final assembly, put in some DISTILLED water (rainwater works, too if its clean. It's naturally "distilled.") and plug it in. It probably won't steam until you pump it a couple of times but I bet it's working again. Be careful with the steam, though. If it works, do the final reassembly. If it doesn't, well you tried. But I bet dollars to doughnuts that it is working again.
Hope this solves your problem! Happy mopping.
CBear in New Mexico
Posted on Feb 16, 2010
I took it back to Costco and they replaced it with no questions asked. I've had the new one for about 6 months now with no problems. One thing I changed though right when I got the new one was I went and bought a bottled of distilled water to use in the tank instead of the hard water from the faucet. I haven't had any problems with it as of yet.
Posted on Nov 27, 2009
I just purchased this last night and the hardwater is the issue because the lady flat out told me on the phone that i could by filters for the machine to prevent those things from happening because the hardwater causes the machine to not last as long. so listen to those suggestions about using bottled water or vinegar or clr because its all about the hard water. the machine will work fine if you keep that in mind.
Posted on Dec 22, 2009
The problems with "NO STEAM" is more than likely that water had been left in the tank for a long period of time. PREVENT this by emptying the tank after use.
Now, if it will not PRODUCE steam, do this: Purchase a bottle of CLR at you local hardware store or WalMart. Empty your Shark of any water in the tank. (Remove cap, remove handles (2), and turn it upside down over the sink or outside. Remove the pad too, if still on.
Pour CLR into the tank FULL STRENGTH until 1/4 full. Set the Shark in the bathtub and pump the handle (there is a stub of a handle still attached) 4-5 times. Now leave it sitting in the tub for 2-4 hours. Remove from tub or plug it in while in the tub. It SHOULD start steaming in about 20-30 seconds! Immediately pull the plug - DO NOT INHALE THE VAPORS OF THE CLR!!!!! Empty the remaining CLR out of the tank, fill with clean water...install cap, shake and empty the water again. Fill and use!
Mine steamed better after I did this better than it did when I used it the first time!
IF, it did NOT start steaming after 4 hours, remove the CLR from the tank, fill the tank with water, shake and empty. Repeat the CLR process. If this doesn't work, I can't help you!
Posted on Nov 24, 2009
I used my steamer for over a year and it started having the same problems as discussed. I called the 800# and this is what they told me....and it worked. 1. empty the mop completely 2. pour cold water back in but very slowly 3. turn the mop on and wait for the steam (be careful when waiting because it will make a loud noise like a mini explosion of steam coming out) They said that there is an air bubble trapped inside. When it finally escapes it's loud.
Posted on Jul 05, 2009
Use 1/4 cup of vinegaar in the water every time you use it helps keep it clean and steaming
Posted on Dec 04, 2009
I have a shark super steamer, I can't seam to turn it off, unless you pull the plug out of the socket.
Posted on Aug 19, 2010
#2 Solution worked for me. I only had to take one hose end off;that was the one leading to the mop head. The end of the tubing broke off. I suppose the heat makes it brittle after awhile. With a blade I cut it back a little bit and reinstalled. Be careful not to cut too much off;there's not much there !
Posted on Apr 08, 2010
Here is how I fixed mine: if the steam stops coming from the mop head attachment - unplug and let it cool for 15 - 20 minutes. Then Very Carefully - disconnect the mop head from the steamer unit. If the steamer unit is operating correctly - what remaining steam held in the plastic body will then vent. this tells you that the boiler portion is working correctly and that the problem is with calcium build up in the mop head // steam diffuser. So - when looking at the diffuser ( the part that actually contacts the follor ) in your hands, one can see a small hole where the steamer unit attaches to the diffuser ( gray plastic coupling ) - this is the steam pathway and it is somewhere along here that the build up has occurred. I used a flexable metal wire and then threaded it into the hole. It should go in about five inches - then just work it back and forth to break up the calcium. It took me two attempts to get this right but it did solve the problem. I guess distilled water is the best solution to avoid this problem again. somehow, considering the cost of the unit new - this sort of problem should have been engineered out or othrewise anticipated for sales in the hard water markets.
Posted on Dec 22, 2010
AFTER YOU PLUG THE STEEMER IN IT USUALLY ONLY TAKES 1 MINUTE TO GET HOT .
ARE YOU PUMPING THE HANDLE ? SOMETIMES I HAVE FOUND THAT IF YOU GO FROM SIDE TO SIDE IT STEEMS BEST. TRY THESE IF IT STILL DONT STEEM FOR YOU I WOULSD RETURN IT TO SHARK I HAVE NEVER HAD ANY PROBLEMS WITH MY MOP
Posted on Aug 07, 2010
I thought the same thing and I was wrong. For me I just hold the button the whole thing while cleaning and it steams for me. Don't know if this is the right way it works but I really really love it! Try this and see what happens. The only down side is the attachments are shot already because I used it so much!
Posted on May 03, 2010
AIR BUBBLE what the !! I paid over 150.00 for mine right off thier site have had it for a month well it worked 3 times and got nothing i just think the thing is ****!!!!! and there should be a WARNING ! if this Air Bubble is true ha what do they think this is a baby or something
Posted on Aug 01, 2009
I have the older shark steam mop with all the attachments. Just paid over $65 for two sets of mop cloths for my large area of tile flooring. Used it two times and now it won't even light up! Bought it from a woman who tried it once, gave it to her housekeeper who was not technical and had no desire to use it so she sold it to me. I purchased the cloths and off I went -- 2 xs!
Posted on Sep 05, 2009
I too had a problem with my shark steam mop My shark is about 2 years old. I used the 6in X 12in head the most. I DO have hard water. I DID no use distilled water. Approximately 6 months ago, my Shark quit working. The boiler / unit worked / got hot, and would not release steam to the pad/head. I tried all the recommendations - vinegar, CLR, soaking the head for up to one week. Realizing my problem was isolated to this one head I liked most, I used the other larger head and the triangle mop head. I nearly ordered the replacement head (rectangle 6in X 12in). I decided to try one more time to clean the clogged head with a wire and small screwdriver. I was not able to fix this head. And then it occurred to me - I don't like the extra large rectangle head. The socket going from shark tank to head appears to be same size as the 6in X 12in...so....I removed the socked from the large head, placed it on the smaller rectangle head I prefer and VOILA! My Shark works again with the smaller head mop. Needless to say, I'm using ONLY distilled water from here on out!
This is the Socket assembly I'm referring to...it does NOT appear to be a part Shark sells separately. I hope this helps!
Posted on Apr 13, 2013
I have the model with the detachable head. Tried to blow into the head but it was clogged. Put some CLR into the connector end of the head and then snaked a thin wire into it. Clog cleared and it's working. I did notice some metallic dust when I opened it up. From now on, Distilled water only and empty the unit after using.
Posted on Mar 24, 2013
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Tips for a great answer:
Jan 07, 2016 | Sewing Machines
Jun 11, 2015 | Euro-Pro S3901 Shark Lift-Away Pro Steam...
Jun 07, 2015 | Shark Vacuums
Feb 20, 2015 | Euro-Pro Shark 60-Stitch Sewing Machine -...
Jun 26, 2012 | Euro-Pro Shark Steam Pocket Multi-Purpose...
Oct 02, 2010 | Euro-Pro Shark SC-505 Handheld Steam...
Aug 11, 2010 | Euro-Pro Shark Steam Mop - Gray/ Purple...
Nov 06, 2009 | Euro-Pro S3325 Handheld Steam Vacuum
Jan 30, 2009 | Euro-Pro Shark Steam Mop - Gray/ Purple...
Aug 30, 2008 | Euro-Pro Shark 80 - 7133
58,470 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: