Question about Kenmore HE2 Plus Front Load Washer
I have a Kenmore HE2t Front loading washer. After each cycle an error code of 5d is shown on the display. What does this error code mean?
5d is a definitely a the code for a plugged discharge. We removed the lower access panel and discovered a virtual treasure: $12.50 in quarters, nickels, dimes and pennies, a pen, a pencil, collar stays, 10 bobby-pins, 3 barrettes, a elastic headband, a draw string, a box cutter, 3 washers, 3 broken zipper parts, a elastic waist band. Amazing it took all to trigger a 5d error code. Hope this helps!
Posted on Apr 03, 2010
5d is a code for drainage problem. I took the lower front panel off and removed the cover for the drainage filter. There was a quarter and a couple of other things in there,... Once removed, everything worked fine.
Posted on Dec 06, 2009
It is not a 5d code, it is Sd for Suds. You are using to much detergent or are not using HE laundry detergent. Please see this site for reference.
Posted on Sep 06, 2010
No solution to this just want to no what i can do to fix it???? do i need to take the drain cover off an see if there is stuff in there or do i have to call some one to come look at it really dont want to do that can do it my self with a lil helf. if any one can help with this prob u can reach me at firstname.lastname@example.org reply kenmore an if u do thank u sooo much
Posted on Sep 18, 2012
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: Just received error code 5D
Hello, welcome to fixya.
Based on your post I understand you have a "SD" error problem (looks like a 5D in the digital display) with a Kenmore washer, the error means an excessive drain time or excessive suds was detected as you may or may not already know.
If you follow the link to my solution to this error designed specifically for "do-it-yourselfers" you should be fixed up in no time. (It's much quicker for me than pasting or retyping the complete solution several hundred times, that's how common this is)
Thank you for visiting fixya for your washer inquiry. Please take a moment to rate my assistance both here and on my tip link and leave a brief testimony.
Posted on Jun 26, 2011
The "F24" error code is a heat sensor error code. The following link explains the error code in detail and the steps to correct it:
In many cases, the connector plug on the NTC sensor wiggles loose and causes the error code. Check the NTC connection first to make sure it is tight and making good contact. This may save you a service call and/or replacement parts. Make sure you UNPLUG the washer before servicing anything inside the unit.
A replacement NTC module (if required) can be purchased at searspartsdirect.com for about $10. Refer to the parts illustrations under the "Tub and Basket Parts" heading.
If you have any questions, please let me know. I hope this helps you.
NOTE: Each washer comes with a technical data sheet located inside the cabinet. You will need to remove the lower toe panel directly below the door to access it. If it is not located directly behind the panel, it will be affixed to one of the interior cabinet walls. The tech sheet includes all troubleshooting tips, wiring diagrams and fault codes with explanations.
Posted on Dec 09, 2009
SOURCE: kenmore he2t error code 21
F21 is a long drain...it is taking too long to drain..you have a something slowing down the drain.. you can remove the bottom panel and clean out coin trap... if there is nothing then you may have another problem... but this is the most common problem..
Posted on Sep 23, 2009
Tips for a great answer:
Dec 06, 2015 | Kenmore HE2 Plus Front Load Washer
Jan 09, 2015 | Kenmore HE2t 3.7 cu. ft. Front Load Washer
Hello & Welcome to FixYa
Error code 5d/Sd means suds have been detected. To solve this
problem you have to take the bottom front panel apart and then clean the drain
filter pump assembly completely, make sure the washer is unplugged before
working on it. Please get back to me if you have any other questions.
Jul 01, 2011 | Kenmore Front Load Washer
Jun 26, 2011 | Kenmore HE2 Plus Front Load Washer
Jun 29, 2010 | Kenmore HE2 Plus Front Load Washer
Jan 24, 2010 | Maytag Neptune MAH6700A Front Load Washer
Oct 29, 2009 | Kenmore Elite 45986 Front Load Washer
Sep 23, 2009 | Kenmore Washing Machines
Jul 13, 2009 | Kenmore HE2 Plus Front Load Washer
28,419 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: