Question about Bosch Logixx WFT 2806 Front Load Washer/Dryer
During the wash cycle a f18 error code flashes. the cycle does not finish and the drum is fill of soapy water.
Open the small flap at the front bottom right of the machine. DONT unscrew the circular white knob yet!!! Use the small black hose to drain the machine into a tray, by removing the small cap on the end of the hose. You will have to use a tray, rather than a bowl because the hose is only short, and keep emptying the tray.(put a washing up bowl next to the machine, so you don't have to carry the tray.) If water does not come out of the hose, then gently unblock it with a piece of wire or fine knitting needle. When water finally stops coming out of the hose, it is time to gently unscrew the white knob anti-clockwise, and pull it forwards. Now you can clear the debris out of the pump rotor, which is behind the white knob. Check with your finger that it can rotate freely, then replace the white knob firmly. Make sure the small cap is replaced on the end of the hose, clip it back into place and put back the cover panel. If this doesn't work then there is a blockage deeper in the machine, and dismantling will be required. Good Luck!!
Posted on Dec 24, 2009
The Manual states
F18 Clean the detergent/solution pump (see page 10) or ,check that the outlet pipe/drainage hose is not blocked.
Best wishes karen
Posted on Jul 18, 2009
F18 is a drainage fault.
The appliance has a set time to drain if it doesn't drain within that time F18 appears in display
Posted on Feb 08, 2008
First do what is suggested above.
Switch machine to off.
Then switch to drain. 1 min later it should finish.
Remove the white cover bottom right.
Drain excess water into low oven dish by pulling the plug from the little black hose.
Then using long pliers twist the blue\white circular anti clockwise. It is likely to be very stiff so be gentle or you'll crack the plastic. Clean this out. You'll find something in there. Check the little impeller at the back can turn.
Run a short cycle.
If you get another F18 error it's likely that you need to pull the machine out from the wall. Check the drainage hose where it connects to the outlet pipe. If it's full of fluff (and it stinks!) you've found the problem.
Clean it thoroughly. And the outlet pipe if you can.
Run a cycle and the problem should be gone.
Posted on Feb 06, 2016
Thanks to your above answers, I just fixed my washingmashine! Thanks!
Posted on Jan 13, 2012
F18 problem that was intermittent and went on for days - resolved at no cost!
Bosch washing machine WAQ283S1GB
F18 would not pump out.
Tried everything suggested.
Drained machine, checked for foreign objects. Removed pipe that went to the drain - looked OK.
Put strong drain-cleaner down drain to make sure that was OK.
Pump was turning sometimes and other times F18!!
Watched youtube videos about the problem.
Pulled machine out and got ready to remove the pump.
New pump would cost £77.
Call out from Bosch £100.
Machine is less than 4 years old.
I had to remove the end connector on the drain pipe, to get it free and the machine could be pulled out and dismantled.
When I checked the pipe before it looked OK.
But as I removed the connector it looked blocked!
Most importantly a large button (off the duvet cover?) was lurking just next to the end of the drain pipe.
I think the button was twisting intermittently and acting like a 'valve' to stop the flow.
All stuff removed, I ran the machine on rinse and spin into buckets and a few more bits came out.
Everything is back together now.
Machine working fine.
Where did the cardboard come from I have no idea. We always check pockets etc before a wash.
Excellent 30 mins work
Posted on May 04, 2019
You have a problem with wasps by draining water.
Drain hose clogged
Posted on Feb 13, 2019
Drain error. Check Pump and filter
Posted on Dec 05, 2018
Error F18 means problem with the drain pump
F18 is a pump timeout error - if you cannot hear the drain pump trying to empty the water when you select a drain or spin cycle, then the pump is the problem.
Posted on Feb 03, 2018
Looks like the pump just needs cleaning out (service flap on front). I have not tried this yet. Ours has the same error. I got this info from someone else, but it's worth a try. Gonna do ours when i get home.
Posted on Feb 08, 2008
Thanks for the answers,just fixed my machine.
Posted on Jan 15, 2013
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Tips for a great answer:
Mar 28, 2016 | Fisher and Paykel Washing Machines
Jan 05, 2016 | Washing Machines
Feb 12, 2013 | Washing Machines
The F11 error occurs when the central control and motor control don't talk to each other.
If one of the controls was actually bad then I'd expect to see the error code every cycle. If it does, start by checking all the wiring connections from the panel to the CCU. Post back your results.
Dec 02, 2012 | Whirlpool Duet GHW9150P Front Load Washer
Apr 04, 2011 | Ariston Technologies Washing Machines
Sep 07, 2010 | Whirlpool Cabrio WTW6600SBT Top Load...
Jul 21, 2009 | Whirlpool WTW6400SW Top Load Washer
May 20, 2009 | Asko Washing Machines
Nov 23, 2008 | Washing Machines
81,863 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: