Question about Kenmore 22622 Top Load Washer

1 Answer

My washing machine (Kenmore 70 Series) does not spin

My washing machine (Kenmore 70 Series) agitates during washing and rinsing but does not spin during draining.

Posted by on

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,937 Answers

This assumes that you have a basic Kenmore / Whirlpool top load, direct drive, neutral drain (it doesn't spin until the pump removes most of the water) machine.

First, see the Sears parts site for your washer:
http://www.searspartsdirect.com/partsdirect/index.action

Enter your model number (###.#######) and you'll see a list of major sub-components with diagrams and parts.


The Kenmore / Whirlpool top load uses a reversing motor to initiate the pump for draining and the transmission to spin.

If you cannot hear the motor trying to turn the pump, (but the washer will agitate) the problem points to the Timer, or the Lid Switch.

Try to bypass the Lid Switch by removing the Console and jumping the two outermost pins on the switch.

Following is a description of how to release the console for access to the pins.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=137

This is a Whirlpool PDF on how these washers operate. It has a diagram on jumping the switch as well as a detailed section on how the transmission works.

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/f7e2147fa98b28cf85257122007475cb/$FILE/L-55.pdf

It also has a troubleshooting guide.

To bypass the switch, you only have to disconnect the power to the washer, tilt the console back, unplug the switch and using an short piece of insulated wire, jump the two outermost contacts on the connector coming from the console and plug the washer back in.

Following is a description of how to gain access to the console and how to remove the cabinet if necessary.

http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=131&osCsid=913ba652cd504fb162f87d892bcb427b

With the jumper in place, try to re-start the washer.

If it works, the Lid Switch is a relatively inexpensive part.

If the problem isn't in the switch, and the Timer continues to move, the problem is likely in the transmission.

We had the same problem:

If you lift the lid, put it down again and the washer begins to spin, the problem is likely in the transmission "Neutral Drain Assembly".

Those cams/gears etc. in that assembly keep the washer from spinning until all of the water is pumped out and then go into spin mode.

Apparently, by opening and closing the lid, torque from the motor starting throws the cams into the right gears so that the washer will spin.

Ours had the same problem, no spin unless the lid was raised and lowered or we shut off and re-started the cycle.

After looking at the transmission parts list (available on a number of sites) and on the Whirlpool site (Whirlpool makes Kenmore) we noticed that the one of the cams in the neutral assembly which is supposed to have a small spring, didn't on ours when we tore the transmission apart again

http://shared.whirlpoolcorp.com/assets/pdfs/literature/Repair%20Part%20List%20-%20W10114743.pdf

Found the part number for a kit (Whirlpool part number 388253 Neutral Assembly) for $15.00 and replaced the cams and gears.

In order to get the transmission out, you have to remove the cabinet, the fabric dispenser and both agitators. The top agitator uses a plastic 1/2" drive bolt (a 1/2" socket extension works well).

You don't have to remove the drum.


http://www.american-appliance.com/catalog/newsdesk_info.php?newsPath=16&newsdesk_id=137

Lay the machine down (after disconnecting power and hoses, remove the pump (two clips), the motor (two screws hold two clips on the motor), lift and set the motor aside.

Remove two 1/2 inch bolts for the motor mounting plate and three 1/2 inch bolts for the transmission.

Pull the transmission, remove the clutch (there is a spring clip that holds the clutch on the main

agitator shaft), remove the 8 screws carefully the transmission holds 14 - 15Oz of oil, remove the clip holding the main spin gear on and check the plastic cams.

If the cam that should have a spring doesn't, or the others look damaged, or the main spin gear is damaged the washer won't go into spin mode.

If that's the problem, install a Neutral drain kit, put everything back together carefully and the problem may be solved.

As an aside, fixing ours cost less than $30 including 80-90 weight gear oil vs. $170 for a new transmission.

Posted on Jan 12, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore Series 70 Top Load Washer Direct Drive Model # 110.20722991 Serial# CL 1134809 Wet Clothes after Spin Cycle


many machine spin a full tub as they are pumping the water out
this helps to even out the washing load and reduce the unbalance situation
when the water is removed , the machine progresses the program to a high speed spin
call a technician as there may be a problem in the program board

Jun 11, 2016 | Kenmore Washing Machines

1 Answer

Kenmore Model 22722 will not drain


Hi,
If you are having a problem with your top load washer then check out this tip...

Washing Machine2_bing.gif does not Pump or Spin
https://www.fixya.com/support/r4617986-washing_machine_not_pump_or_spin

If you are having problems with your front load washing machine2_bing.gif then checkout this tip...

Front Load Washing Machine2_bing.gif not draining and or not spinning
https://www.fixya.com/support/r4784376-front_load_washing_machine_not_draining

heatman101

Jun 01, 2010 | Washing Machines

1 Answer

Kenmore Heavy Duty Series 70 washing machine gets stuck in cycle.


Either your timing motor has broken or the gears that it drives are stripped. The timing motor is easy to replace but if the gears are stripped you will need a whole new dial assembly.

May 09, 2017 | Kenmore Washing Machines

1 Answer

Agitator does NOT spin along w/ drum during spin cycle


If this is the old style that uses a belt, it is not worth fixing. But the problem sounds like the wig-wam is not functioning properly. Most of the time it was a wire broken since it moves back and forth constantly.

Jan 28, 2010 | Kenmore Washing Machines

1 Answer

Kenmore series 70 washer leaks during rinse?


the was exhaust hose is either plugged or cracked. also check the drain it is put into as this sometimes will be puleeged with fabric from the clothes you wash

Jul 10, 2009 | Kenmore 22422 Top Load Washer

1 Answer

70 series kenmore washer won't agitate help model #82873120


No wash, no spin read THIS
Spins, pumps, won't agitate right: check THIS out


If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Mar 27, 2009 | Kenmore 22422 Top Load Washer

Not finding what you are looking for?
Kenmore 22622 Top Load Washer Logo

2,969 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

fordexpert

Level 3 Expert

5692 Answers

Harvey Mahal

Level 2 Expert

39 Answers

Kristen Denison
Kristen Denison

Level 1 Expert

13 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...