Question about Maytag CWG3100A Gas Single Oven

1 Answer

Broiler works fine, oven will not come on ? - Maytag CWG3100A Gas Single Oven

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 49 Answers

Check all fuses. Make sure the bottome element is seated properly. If the top and bottom element are the same you could always remove the top one and place it in the bottom (they usually just push-in and pull-out similar to the elements on the top of the stove) to see if it is just the element. A replacment element may be all you need.
Hope this helps
Jer

Posted on Jan 16, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Broiler element doesn't work


Reseating the Element The broiler is heated using an electric element which should be clipped in to the top of the broiler enclosure. If this has come loose then it might not be making contact with the necessary terminals. Try to reseat the terminal but before doing so you must ensure that the electricity is turned off.
Testing the Element The element is what heats up and cooks the food in the broiler. Over time the heat can damage the broiler element. These elements are supported by stand-offs and if the element burns out or becomes damaged then this can be a common reason why the broiler isn't working.
The easiest way to test whether this is working is to turn the broiler on and look at the element. If it is working correctly then the element should be glowing red.
Another slightly more complicated test for the broiler element is to remove the element from the oven and disconnect it. Then use a multimeter to check the continuity of the element. Set the multi-meter to measure resistance and then put it either side of the element. The normal measurement should be between 20 and 40 ohms. If the element is infinitely resistant then this means it's broken and will need to be replaced.
Testing Oven Controls Another reason why the broiler will fail to work is because of problems with the oven controls. A thermostat is used to set the temperature of the broiler, and the oven selector controls are used to control the setting of the broiler.
Turn the oven controls on to see whether the broiler is working properly. If not the controls can be removed and tested using a multimeter. Check the outputs to ensure that the controls are working correctly.
These can also be replaced if required by fitting a replacement part designed specifically for your oven.


Read More: Troubleshooting an Oven Broiler Doesn Work

Feb 09, 2014 | Thermador SEC302 Electric Double Oven

1 Answer

Hotpoint oven won't heat above 250 degrees broiler works fine as well as the stove top


either its the oven sensor rod located at the top of the ovens cavity,or your bake element could be getting a hot spot which is when it gets a discolored spot in the element and can no longer pass sufficient current to heat the oven past 250 degrees

Jul 28, 2012 | Hotpoint Ovens

1 Answer

Oven will not light ,broiler and top of range light fine


the ignitor is not working its bad,you should see a bright orange glow below the oven base just as when you start the broiler look up at the top of the oven and watch this ignitor glow before ignition,the bottom should do the same,you can also see this from the back side of the range at the base,if you don't use the broiler you can use that ignitor for the oven ignitor as these ignitors are identical,but then you will have no broiler

May 11, 2012 | Frigidaire Ovens

1 Answer

Oven not working. Top, broiler, and warmer are working.


Have you checked for proper gas flow into the over or broiler? This is a gas valve back there that will sometimes go bad. Also there is a sensor near your knobs, it is a timer that will go bad, the valve is about 85 dollars and the timer is about 65 dollars

Feb 08, 2009 | Kenmore 40494 / 40495 / 40499 Electric...

1 Answer

Roper drop in range broiler will not light


YOU HAVE A SHORT ON THE BROIL CIRCUIT PROBABLY ON THE ELEMENT IT IS ELECTRIC CORRECT?

Jan 07, 2009 | Ovens

1 Answer

Oven/Broiler Igniters for KitchenAid range KGST307


Oven bake ignites usually have lifetime 5-7 years. If igniter glows but gas not came in - replace igniter. Same with broil igniter.

I’m happy to help further over the phone at https://www.6ya.com/expert/vitaliy_f406165329c75ede

Dec 09, 2008 | Ovens

2 Answers

My Oven and broiler won't heat but stovetop burners work


I have a Frigidaire Model Number GLGF377ASF. The stovetop burners work just fine but the oven and broiler do not work.

Dec 08, 2008 | Frigidaire 30" Self-Cleaning Freestanding...

Not finding what you are looking for?
Maytag CWG3100A Gas Single Oven Logo

162 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Ovens Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Paul Carew

Level 3 Expert

3484 Answers

Brad Brown

Level 3 Expert

18154 Answers

Are you a Maytag Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...