Question about Maytag Neptune MAH6700A Front Load Washer
The fabric softener dispenser does not dispense. The soap and bleach do dispense.
The fabric softener dispenser is notorious for clogging. Liquid fabric softener is essentially a liquid form of wax. After a period of time it begins to gunk up the inside of the fabric softener dispenser. If you remove the dispenser drawer and look into the cavity, there should be a series of holes in the upper part of the compartment where water sprays into all the dispenser trays. These holes get gunked up and clogged and water will not dispense properly. As a result, the washer goes through a complete cycle, but the dispenser stays full. If this is the case, you can take some cotton swabs and/or toothpicks and clean these holes real good. It may be a bit meticulous, but it should take care of the problem. Post back and let me know if this helps.
Posted on Feb 11, 2008
The fabric softener dispenser (and bleach dispenser, same water line) on the Maytag MAH 6700 model works by time (controlled by the circuit board) and water flow from the cold water inlet valve. Check the screen on your cold water inlet. If clean, the water inlet valve may need to be replaced. They (two solenoid units together)are not repairable. If you are mechanically inclined take a look at the cold water inlet valve that has the rubber tubing running to the "bleach" dispensor nipple. It will have a water flow restrictor in it at the inlet valve. On my unit a piece of "stray" plastic was partially clogging the flow restrictor. I carefully drilled the valve out enough to remove the stray plastic. Now both the bleach dispenser and fabric softener dispenser work properly and at the correct times during the wash.
Good luck with your repair!
Posted on Dec 17, 2008
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Tips for a great answer:
Sep 02, 2015 | Whirlpool duet Washing Machines
Hello - There are several things that could cause the fabric softener to not dispense into the washer. Are you sure the liquid in the dispenser after the wash is fabric softener? If it is fabric softener, the solenoid that lets the water into the dispenser is not working. This solenoid is located on the back of the dispenser. It only gets voltage during the dispense time and fills the fabric softener dispenser with water. The fabric softener dispenser fills while the washer is filling for the rinse cycle.
When the washer begins to fill for the rinse cycle, the fabric softener solenoid is energized and water flows into the fabric softener dispenser cup. When the cup is full the water siphons out and softener and water flow into the tub.
If the liquid in the fabric softener dispenser is pure softener you may need a technician to diagnose and repair the problem. The voltage will have to be tested to the softener solenoid and a volt meter is required.
If the liquid in the fabric softener dispenser is water you probably need to clean the dispenser cup. **** will build up in the siphon tube and stop the liquid from going into the washer tub. The incoming water will dilute the softener and overflow the dispenser cup and run into the tub. The instructions for cleaning the dispenser should be located on page 43 of the use and care guide that came with the washer.
If you don't have the use and care guide these instructions will help. Open the dispenser until it stops. In the left rear corner of the dispenser, there is a release that is labeled push. Press down on the push area and you can slide the dispenser drawer out.
Remove the insert from the bleach and fabric softener compartments. Clean the bottom of the insert and the bleach and fabric softener compartments. Reinstall the insert and put the drawer back inside the washer.
To test the siphon action slowly pour water into the fabric softener compartment. When the water level goes above the maximum line stop pouring. The water should all drain out.
Hope this information proves to be helpful however if it is ineffective please contact a professional to move forward accurately.
Oct 26, 2012 | Frigidaire Affinity ATF7000E Front Load...
Apr 30, 2011 | Whirlpool LHW0050PQ Front Load Washer
Jan 21, 2011 | Frigidaire ATF6000ES Front Load Washer
Sep 04, 2008 | Whirlpool Duet GHW9150P Front Load Washer
Jun 05, 2008 | LG WM2688H Front Load Washer
Feb 01, 2008 | Whirlpool Duet GHW9150P Front Load Washer
13,737 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: