Question about Asko D1976 Built-in Dishwasher

2 Answers

My Asko dishwasher is not draining. Code F2

My Asko dishwasher is not draining. It stops mid-cycle and flashes a code "F2." I push start and it finishes, but has water at the bottom.

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

Drain plugged, hose kinked or discharge pump bad

Posted on Jan 19, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 4 Answers

The overflow capture plate is flooded. Basically, any overflow falls to the bottom of the unit to protect the floor. There's a foam floater attached to a lever which floats up and triggers a switch sending F2 error. Best to open bottom front skirt and sponge up any water still in the spill sump, or remove back panel to better access the water and sponge it up. F2 error message vanishes once float drops and machine starts working correctly again. Remember to fix cause of flooding, which is usually are blocked sink drain pipe. This blockage causes sink water to flow into the machine instead of down the drain.

Posted on Apr 09, 2015

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My asko D5155 stops washing and flashes F7


LED L1+ L2/Fault code F7, Pumping out fault (machines with
pressure sensor)

Water not evacuated after 120 seconds pumping out. Program
interrupted.
Check: Drain pump, hoses, installation of drain hose, control unit and wiring.

Dado

Oct 06, 2015 | Asko Dishwashers

1 Answer

F2 Code???


Probably blockage in pump or sump

Jun 17, 2013 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Zanussi tempoline not working, son twisted nob mid cycle it then stopped and wouldn't drain. Now not doing anything! Any ideas? I assume its a error code flashing up


The first step of a dishwasher is a drain / rinse drain. I would turn the dishwasher off at the socket, turn the nob to the off position only turn this in a clock wise direction IE: the direction the nob would naturally move. Turn on back at the wall and start as you would normally. The dishwasher will empty the water out in its first step then should cycle through as normal.

Feb 08, 2013 | Dishwashers

1 Answer

ASKO D1976 model. We have a F2 error message. Water has now been drained but we are unable to remove error code or have dishwasher return to normal cycle


Display shows an error code. Do the following:

1. Unplug washer or disconnect power for one minute.
2. Plug in washer or reconnect power.
3. Re-select the cycle and press Start.

NOTE: If the error remains on the display, call for service.

May 27, 2011 | Dishwashers

1 Answer

It has been flashing an F2 error code and the timer starts at 65 then switches to "1" which stays on during the cycle. Now it will run for about a minute then stops completely. Can you suggest any parts...


Hello,

Welcome to FixYa.


The "F2" for Asko dishwashers indicates either the unit is overfilling, or the valve itself has failed.

The problem is likely the fill valve, based on your description... "It has been flashing an F2 error code and the timer starts at 65 then switches to "1" which stays on during the cycle. Now it will run for about a minute then stops completely".

Depending on the series of dishwasher you have, determined by serial number ( I don`t mean the model... I got it is a 1895 ) because those Asko machines had a revision to their valves moving from a dual solenoid to a single, the single substituting all dual coil valve units.

i.e.


f98cb6d.jpg

The original Asko number would be # 8057508 and available at most brick & mortar parts vendors or on- line places such as "repairclinic.com".

** turn off the breaker at the service panel before servicing the unit...safety first**

To check the valve will require the removal of the lower panel/kick plate or also referred to as a toe panel, and with the aid of an ohm meter and at least one wire removed from each/the coil, measure the ohm value of the coil.

The valve will be on your right...

i.e.

451817e.jpg
It should not read infinite, but rather 0 to 93Kohms.

That should move you forward and hopefully solve the problem. Let me know if anything is not clear or if you require further assistance.

Thank you for choosing FixYa and good luck.

** If you have any reservation or are not completely confident servicing this unit please call in an authorized Asko technician **

These can be very difficult to service for one inexperienced, I see so-called pros mess them up all too often.

Regards,


Macmarkus :)


Oct 07, 2010 | Asko 24 in. 1895 Built-in Dishwasher

2 Answers

F2 error message after dishwasher backed up when draining. Asko brand.


Hi


Thanks for using FixYa. Error F2 in your Asko Dishwasher means high water level. This error occurs due to plugged/bad water pump and/or a bad inlet valve. If the water pump and/or water inlet valve are bad it should be replaced to resolve this issue. Please do rate the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee

Jun 26, 2010 | Dishwashers

1 Answer

Asko 3350 F2 fault meassage keeps flashing


you have a blockage try the drain spigot under the sink or the pump may be blocked.

Apr 23, 2010 | Asko 24 in. D3350 Dishwasher

1 Answer

Asko 20605 washer stopped mid-cycle, now no power?!


The ECU should be tested. Look for the service manual inside the chassis for troubleshooting procedures.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Mar 04, 2010 | Asko Washing Machines

2 Answers

Asko d1876


I'm not sure about that model, but on an older one, just under the drain area there is a piece os styrofoam attached to a switch. I guess if it rises it activates the circuit. Problem is if it drys it sticks, so push it down with your hand gently. This involves taking off that bottom kickplate area, but that's the only way in there.

Jan 25, 2009 | Asko D1876 Dishwasher

Not finding what you are looking for?
Asko D1976 Built-in Dishwasher Logo

1,590 people viewed this question

Ask a Question

Usually answered in minutes!

Top Asko Dishwashers Experts

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

MARLON KELLER

Level 2 Expert

111 Answers

Are you an Asko Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...