Question about Cisco Catalyst 4506-E Cat4500 E-series 6-slot Chassis Fan No PS WS-C4506-E

1 Answer

Password Recovery for Cisco Catalyst 4506 - Cisco Catalyst 4506-E Cat4500 E-series 6-slot Chassis Fan No PS WS-C4506-E

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 121 Answers

Please see Cisco's page at http://www.cisco.com/en/US/products/hw/routers/ps5199/products_password_recovery09186a0080093e12.shtml
for step by step details and more in depth instruction.

1. Reboot
2. Press the "break" button on your keyboard within 60 seconds of the power-up to put the router into ROMMON mode.
3. confreg 0x2142
4. reset
5. type, "no" when prompted to enter the initial configuration dialog.
6. enable
7. copy startup-config running-config
8. conf t
9. enable secret <password>
11. config-register 0x2102
12. reboot again

Posted on Feb 19, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to replace the Chassis of CISCO 4500 switch. Can i know Step by Step procedure to do this change.


http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/hardware/installation/guide/78-14409-08/04replac.html.......................... please follow the above link

Feb 11, 2011 | Cisco Catalyst 4506-E Cat4500 E-series...

1 Answer

I just replaced cisco 4506 with new 4506-e, the uplink port didn't work for trunking


Hi, if you installed a Supervisor 6L-E 10GE (X2) in the new 4506-E and you want to use the two 10GE uplinks as Gigabit, you need to type in the following config lines:

hw-module module 1 port-group 1 select gigabitethernet
hw-module module 1 port-group 2 select gigabitethernet

Jan 17, 2011 | Cisco Catalyst 4506-E Cat4500 E-series...

1 Answer

Hello, I tried the steps you have mentioned in the link below: http://www.fixya.com/support/t3932749-password_recovery_cisco_catalyst_4506 and the other similar resolutions on the cisco website but...


Please make sure you have only one supervisor module installed on your switch or else pull out the backup sup module and do this activity .

In the last step of reset it will ask to save the config.

do you wish to save this configuration? y/n [n]: y
You must reset or power cycle for new configuration to take effect

do not forget to type in y there.

Jan 01, 2011 | Cisco Catalyst 4506-E Cat4500 E-series...

1 Answer

How to speed changed in gigabitEthernet 2/1 from cisco 4506switch


Hi

Ok so once you have logged into the router you do the following

go into enable mode by tyoing in en
Then type in conf t
then type in int X where X = the interface
then type in speed 100
then type end

This will set the interface to 100mbps

Feb 27, 2010 | Cisco Catalyst 4506-E Cat4500 E-series...

1 Answer

Hi, what's a password on the router Cisco Catalyst 2960 default?


Try using username (none) pass public/private/secret or
cisco - cisco, ADMIN - changeme, pixadmin - pixadmin, root - attack, superuser - superuser as username - password. These are the defaults credintials for the Cisco routers.

Stelios.

Feb 22, 2010 | Cisco Rf Catalyst 2960 24-PORT 10/10

1 Answer

Default pasword


Cisco switches dont have a default password.
You will have to perform a password recovery process that is quite extensive.
You need to console into the switch using hyperterminal or teraterm and follow these instructions located at: http://www.cisco.com/en/US/products/hw/switches/ps628/products_password_recovery09186a0080094184.shtml

Dec 13, 2008 | Cisco Rf Catalyst 2960 24-PORT 10/10

1 Answer

Problem with module WS-X4548-GB-RJ45V in Catalyst 4506


use software advisor in Cisco website to verify it.just follow the process.

console to it and show diag and see whether it detectable or not.

hope this help.

Dec 02, 2006 | Cisco WS-X4548-GB-RJ45V= Expansion Module

Not finding what you are looking for?
Cisco Catalyst 4506-E Cat4500 E-series 6-slot Chassis Fan No PS WS-C4506-E Logo

3,024 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cisco Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Ekse

Level 3 Expert

13434 Answers

Jeffrey Groves
Jeffrey Groves

Level 3 Expert

573 Answers

Are you a Cisco Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...