Question about Sewing Machines

1 Answer

I have GE Simon 3 security system that was working. All of a sudden the panel is not poering on. I checked the AC Transformer input/output and it is working.

Posted by on

  • Anonymous Jan 22, 2010

    I already replaced the backup battery (couple of months ago).



    DC Out from the edge of board is not showing any output.



    Where is the fuse located?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,185 Answers

You need to check the fuses first with a continuity tester then the 12v DC out at the edge of the PCB, if you can read 12vdc then you have a component failure if not then the rectifier has popped.

(The AC transformer supplies an AC output of say 16v and it is then rectified and smoothed before going to the pcb)

If you have had the same backup battery in for more than 3 years it may have popped that circuit

Posted on Jan 22, 2010

  • Anonymous Jan 23, 2010

    Take off the main cover



    Enter the code to stop the alarm



    Look for a 20mm glass fuse



    Normally there are two sometimes three depending on issue



    You need to remove them from their holders to check them

×

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Transformer output power singer quantum stilyst 9960


The transformer is protected by a fuse and if that is not the problem then you have to order the whole power supply unit from singer. The transformer is not available separately. If there are any numbers on the transformer please post and I will see if it can locate one. The issue is some manufacturers use custom wound units. Otherwise buy the whole thing: https://www.sewingpartsonline.com/power-circuit-unit-singer-416401701.aspx

Jul 13, 2018 | Singer Sewing Machines

1 Answer

I just moved to France and brought my Juki TL-2010Q from the USA. I plugged it in with a European adaptor and it blew the fuse? Is it fixable? Where do I get a replacement fuse? Thank you! Suzanne


Did you mean an 'adaptor' (as in two-pin to 3-pin) or a transformer ?
It is a DIFFERENT electrical system in Europe to the USA.
The USA is 110v and Europe is 240 or 220v. The machine is
probably burned out. You would need to take it to a dealer to be checked. You can ONLY use USA electrical equipment with a TRANSFORMER, so that it can function on the different European electrical system. Good luck !

Sep 12, 2016 | Juki Sewing Machines

1 Answer

Juki lk1903b machine is not working E7 is appers


HI
regarding JUKI LK-1903B Eror E7:
1-Machine lock error ( The main shaft of the sewing machine does not rotate due to some troubles ). please check if machine rotate smoothly by hand or not.
2-main motor problem ( AC servo motor problem ) motor part No.:401-38137.
3- check connection CN-15 / CN-17 from SDC board to main motor.
4 - problem in SDC servo board ( No output for main motor ). SDC servo board part No.:401-42267.
best regards
ASHRAF ABOZID
aabozid@hotmail.com
CAIRO - EGYPT

Apr 10, 2015 | Juki Sewing Machines

3 Answers

Display does not light up on PFAFF 1475 CD


These instructions apply to PFAFF 1475 CD. They may also work for other machines.
If you have some advanced electronic repair skills and tools, check the following:
For 220 Volts models - there is a fuse next to the power input, make sure it is good. There is no such a fuse for 120 Volts model.
If the fuse is Okay, you have to get access to the main circuit board by removing the bottom cover.
Check the primary on the transformer for 120 V AC (220 V AC respectively). Check the secondary side for 5 V AC (luminescent display), 9 V AC (turns to 5 V DC by rectifier, 4700 micro farads capacitor and a 5 V regulator STI L387A) and 28 V AC (turns to 35 V DC by rectifier and 2200 micro farads capacitor.
Pay attention to two soldered round fuses in series with the secondary 9 V and 28 V - both should be good. On the big capacitors you should have 9 V DC and 35 V DC.
Common symptoms for bad small 22 micro farads capacitors next to the some of the IC's - there are 5 of these: These capacitors are in parallel with 5 V DC.
## All of the LEDs light up but the display is blank
## All of the LEDs light up, the display is blank, and after a minute no LEDs at all
## No LEDs nor display.
Replace ALL five 22 micro farads capacitors using a good desoldering pump or desoldering station!.
Enjoy your resurrected PFAFF 1475 CD machine!!!
I just did this procedure on my aunt's one (Made in West Germany around 1990).

Feb 01, 2015 | PfaFF Sewing Machines

1 Answer

Change 220v to 110v


You will need a transformer. If the appliance is 220V to start with, you need a step-up tranformer, that is, 110V supply UP to 220V output. The other way round, a step-down transformer.

They are sold at hardware outlets and electronics suppliers like RadioShack.

Feb 13, 2014 | PfaFF Tiptronic 2040

2 Answers

My Pfaff 1471 lights up, but does not run. This model has no fuse. I checked the foot pedal with an ohm meter, & it sends a variable signal. My house took a direct lightning strike 2 weeks ago, &...


Were the base plate pugs into the power leads, you should read about 6-18 is ohms. Open and short is a bad transformer.

Also there are fuses, 2-3 right next to the transformer, small blueish and round are the shapes. They go bad often.

Sep 22, 2011 | PfaFF Sewing Machines

1 Answer

I need to know the amperage for the power source for the tiny tailor. The power source is missing and i need to replace it.


I have the original power source - it is Hon-Kwang, class 2 transformer D45-10
Input 120V 60 Hz 12w
Output 4.5Vdc 800mA
Hope that helps - that is all it says

Dec 16, 2010 | Singer Tiny Tailor TT700

1 Answer

The Husqvarna 980 Prism was working fine and then switched off. After a few minutes it came back on, then after about 15 minutes sewing it went off again and I have not been able to start it.


Hi,


Most probably it has blown a fuse in the transformer. The transformer is under the machine that is secured by four screws. Take this out and release the transformer out, it will still be hooked to the connecting wires, so you need to carefully disconnect them. Once you open the transformer you will see a small fuse, you need to replace the fuse.


Please get back to us if you have any further query.


Have a nice day.

Dec 08, 2010 | Husqvarna Sewing Machines

1 Answer

When I turned on my viking 980, the power went on for a moment and then went completely dead. Checked that outlet has power, all connections are made securely.


More than likely it blew the fuse in the transformer, although it is fairly easy to replace this fuse it is important to find out why it blew. The transformer is under the machine and held in place by 4 screws. Take this out and ease the transformer out, it will still be hooked to the connecting wires just gently disconected them. Once you open the transformer you will see a small fuse, you can take it to radio shack and get an EXACT replacement.
I have fixed 100s of these of the last 25 years

Jun 28, 2009 | Husqvarna Viking 1

Not finding what you are looking for?
Sewing Machines Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sewing Machines Experts

Cindy Wells

Level 3 Expert

6068 Answers

Chris Wetmore

Level 2 Expert

190 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

Are you a Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...